0
Honda Accord
The Honda Accord series is a family of medium-sized cars produced by Honda from 1976 to the present. It was launched as a 1600cc engine-powered mid-sized hatchback sedan, with design similar to an upgraded modern Honda Civic.
5,977 Questions
After How many miles is a timing belt on Honda Passport due?
i have a 2002 Honda accord, and my manual says 105,000 miles.... but, i am at 101,000 miles and about to get mine done in the next two weeks b/c i am paranoid-- it will completely screw up your engine if the timing belt breaks. my advice is, if you are anywhere near 105K miles then i would get it replaced ASAP.
How do you replace all brake lines on A Honda Accord?
Brake lines (which are steel) or brake hoses (which are hoses)? Hoses are easy:
Tools and parts needed:
Set of tubing wrenches
Jack and four jackstands
Motive Power Bleeder with the correct adapter for a Honda
Two brand-new quarts good brake fluid - a name-brand DOT 3 is fine, that's what all Japanese cars have in them
Brake bleeding wrench, hose and container.
Four RUBBER brake hoses. Don't use stainless steel hoses unless this is a race car that'll never be used on the street - very, very few stainless brake hoses are DOT-approved and you don't need them on the street anyway. (The draw of stainless brake hoses is they can't expand under pressure and rubber ones do. The reality is a street car's braking system doesn't have enough pressure in it to stretch the hoses anyway.)
If it's been a while since your last brake job, a set of brake pads and some grease for the backs of them
How to:
Jack up your car, put it on stands, remove the wheels and put the wheels under the car with the pretty side facing down. If the car falls off the stands, you want it to fall on the wheels and not the ground.
Connect the brake bleeding hose to the right rear bleeder nipple, put the end in the catch container, open the nipple, open your car door, sit on the ground and very gently pump the brakes until fluid stops coming out. Do the same thing on the left rear. Close both bleeder nipples.
Use a tubing wrench to change the brake hoses. This is the easiest part of the whole thing: remove the old hose and install the new one in its place.
If you have new brake pads, put 'em on now.
At this point you need to fill your brakes with fluid. Test the bleeder by connecting it to the master cylinder and pumping it up to 15 psi. If it doesn't leak or explode, unscrew the pump to relieve the pressure and unhook the adapter from the master cylinder. Open the first quart of fluid. Fill the master cylinder reservoir, then pour the rest in the Power Bleeder. Connect the bleeder to the master cylinder and pump it up to 15 psi. Go to the right rear wheel. Hook up the bleeder hose, put some brake fluid in the container (if you have some old but unused brake fluid sitting around, this is a good use for it), and open the bleeder valve. A LOT of air will come out, then fluid with bubbles, then dirty fluid with no bubbles, then clean fluid with no bubbles. When you get clean fluid with no bubbles, close the valve and go to the left front wheel. Make sure there's fluid in the pressure bleeder tank. Pump it back up to 15 psi and bleed the front wheel. Check the pressure bleeder, go to the left rear wheel and bleed it, then bleed the right front wheel after checking the bleeder again. Next, put half the second quart of fluid in the bleeder and rebleed all the wheels just to make sure. (If you have a manual transmission with hydraulic clutch, bleed that after the wheels are bled.)
Finally, put your wheels back on, set the car on the ground, tighten the lugs to 90 lb-ft, and go for a ride.
To install brake LINES, you'll need to do all those things but you'll have to add the brake lines (Honda calls them "brake pipes") you need to your shopping list. They're rigid steel so it takes quite a bit of work to snake them up into position.
How do you stop a radiator leak in a 1994 Honda Accord?
The only way that actually works is to change the radiator. "Radiator Stop Leak" products don't really stop anything, except maybe you being able to spend that $5 on a Big Mac or something.
Code 22 on a 1994 Honda Accord how do i solve this problem Please help?
Code 22 on a 1993 Honda Accord means the VTEC oil pressure switch is defective. The most common fix to this error code is simply checking your oil level and fill it back up. If your oil level is good, check the wiring to the pressure switch.
How do you restart radio on 2004 Honda Accord showing ERROR E after battery disconnect?
You must insert a 5 digit code. Look in the glove box and owners manual for the code. If you cannot find the code then go here http://owners.honda.com and register your Honda. After registering and signing in look on the left under Quick Links and click Retrieve Radio/Navi code. Follow the instructions.
Does a 2004 Honda accord 4 cylinder have a timing chain?
Yes, the 4 cylinder has a cam chain but the V6 has a cam belt.
Where is the transmission dipstick located on a 96 Civix EX?
Looking into the hood, it will be on the left side in the middle. Just above the coolant. It should be a yellow dipstick
What does p01705 for 98 Honda accord mean?
Automatic Transaxle Concerns
http://www.obd-codes.com/trouble_codes/honda/
Take the steering wheel cover and pull the switch up.... most likely your stuck.
How do you change cabin filter for Honda accord 2004?
No pictures but the filter change is very simple. I just completed the replacement on my 2004 Accord V6.
First locate components to be removed.
Look on the right side of open glovebox and locate a plastic lever. You will see groves on the end connected to the glovebox. The groved area is the spot to place the thumb in order to press this lever off the glovebox.
Lay on the floor on the passenger side and look up under the glovebox. You will see two brass colored screws one on each side of the glovebox. these screws go up through two square plastic hinges attached to the glovebox and in the the dash frame.
With the glovebox closed remove the two brass colored screws and lay them in the floor.
Open the glovebox and hold the glovebox with your left hand and press on the plastic lever located on the right side of the glovebox. This lever is slotted and will pop off the glovebox.
Lay glovebox in the driver seat.
Look straight in behind the glovebox. You will see a rectangular black plastic cover approximately 1.5 inches wide by 8 inches long. On the right and left side are arrows pointing in. Press the arrows and pull out on the cover. This will slide out the tray that holds the filter. Remove old filter and insert the new one, flow arrows pointing down.
Retrieve glovebox hold in place and attach plastic plastic lever to the right side of the glovebox. The reverse of removal.
NOTE -The two plastic hinges located on the bottom of the glovebox fit underneath the dash frame.
While holding the glovebox in place (the glovebox latch may hold glovebox in place while installing screws) re-install the two brass colored screws through the plastic hinges into the frame and tighten.
Filter Replacement Complete.
Where is the egr valve on Honda civic 2000?
The EGR Valve is locaded right on the back of the manifold on the left side is the one that looks like is mostly glued not screwed.....
How many catalytic converters does the 1994 Taurus wagon have?
1994 and 1995 Ford Taurus wagons have two catalytic converters. They either
came with 3.0L or 3.8L V6 engines. Each exhaust manifold (3 cylinders front and
3 cylinders back) feeds into one catalytic converter. These then go into a 'Y' joint to an expansion joint and onto the muffler and out the tailpipe.
icrich@ hotmail.com Toronto
The firing orders it
Where is the trip reset on Honda Accord?
The dial you use to adjust the dash light brightness. Push and hold it in and the trip odometer will reset to 0.
When should you change timing belt in Honda Accord 1987?
The cam belt must be replace on the 1987 Honda Accord every 60,000 miles or 10 years whichever comes first. Warning: This is an interference engine.
How do you replace a starter on a 1989 Honda accord lxi?
Disconnect the battery. There's two bolts one on the bottom is hard to reach, the one on top is not too bad, and one wire. have some good tools or your hands will hurt. whne you put new one in make sure you dont ram it in there. Think of it as slow sex.
Where is the AC compressor on a 1991 Honda accord?
If you are facing the front of the vehicle the AC compressor is located on the right side of the engine, below the alternator.
What is the warning sign that looks like screwdriver on 2006 Honda Accord?
Normally this light with either a wrench or screwdriver means you car just needs a regular scheduled maintenance. More than likely an oil/filter change. Refer to your owners manual to verify this. If you have no owners manual then call your local Honda dealer.
Letter to transfer vehicle from one peroson to another?
sample letter of transfer from one person to another
Dose a 1998 Honda 300 ex has transmission oil and how do you change it?
Yes, the engine oil . Just change the engine oil,it lubes the trans & engine. I recomend 10w40 for normal riding & 20w50 for hard riding.
What could be wrong if a 1992 Honda Accord LX will not start?
I just had to replace my main relay. My car wouldn't start either. Now it starts every time I turn the key.I have a 1989 Honda Civic. When it got hot, it would not start. I also replaced the main relay, which I found online for like 30 dollars, and replaced it myself. It was very easy to do and I have never had a problem since.
