answersLogoWhite

0

Hyundai Accent

The Hyundai Accent is a subcompact car produced from 1994 to the present. The Accent was named by J.D. Power and Associates as 2008’s most dependable subcompact car.

1,367 Questions

How difficult is it to put a 2 liter Hyundai Accent motor into a 1997 Hyundai Excel?

2

To be honest if you oversize your exhaust on an N/A car then you risk reducing the "backpressure" to the engine and hence reduce the overall performance. Just by changing the backbox on a 1995 to 1999 Hyundai Accent / Excell on a stock engine will change the "power band" from about 2k RPM to about 4k RPM. By getting the TB mod you will hopefully negate the larger exhaust backpressure reduction, but for a 2.0 litre conversion you will need to referr to www.performancehyundai.com ;)

I put a 2L late model excel engine in my 92 excel(1.8L) not sure the difference between elantra and excel but all i did was kept the original "juicy bits" like radiator ECU and gearbox ect. and everythign fit perfectly, no over pressure or anything.

Where fuses Hyundai Accent 2001?

I have 2000 accent, my fuse box is to the left of your feet as you sit in the drivers seat, on the side panel. There should be a small door. Hope this helps you out.

Where are the glow plugs on Kia carens?

the glow plugs are situated on the rear of the engine above exhaust manifold at a 60% angle took some time to find mine but they are there

What is the front leg room in the 2012 Hyundai Accent?

The 2012 Hyundai Accent has 41.8 in. of front leg room.

How do you replace 2005 Hyundai accent headlight bulb?

Open the hood and look behind the headlight. You will see a rubber cover with a electrical plug and wires coming out of it. Remove the electrical plug by squeezing the sides while pulling. Then take the rubber cover of. The bulb will be held in place by a metal wire. The wire if connected to the body of the headlight at the top, and held in place by a hook on the bottom. Push down on the bottom of the metal wire and it will come off the hook, and the bulb will come out freely. Then put in new bulb and reassemble in the opposite way you dissembled it. Have fun.

How much is an alternator?

Year and engine size? Alternators typically range from $200 - $400 for OEM Reman

Where is the OBD port on 1996 Hyundai Accent?

The 1996 Hyundai Accent OBD 2 port is on lower edge of dash next to kick panel

What is the wheel base of the 2013 Hyundai Accent?

The 2013 Hyundai Accent has a 8 ft. 5.2 in. (101.2 in.) wheel base.

How do you change your accent?

By living in a different area for a few years or by subjecting yourself to a certain culture such as American TV for an excessive amount of time.

What could be wrong if the fog lights on a VW Beetle are not working?

Pull out on the light switch when you have turned it to the right to turn on the lights.

How do you replace a transmission sensor in a '99 Hyundai Accent?

im sorry i got confused i was trying to ask a question i didnt pay atten on what i was doing

What size battery does a 2007 Hyundai accent need?

The battery for all 2007 Hyundai Accents is a "group 35". However, any battery you buy from an aftermarket source is not going to fit properly in the rear of the battery tray when bracketed down from the front. The battery will not be wide enough front to back to fit securely and you run the risk of the battery tipping forward during sudden braking or frontal impact. You will need to go to the dealership for the proper fitment for your 2007 Hyundai Accent. Figure spending approximately $100 for the battery before installation.

Will the 02 Hyundai Accent engine fit an 02 Kia Rio?

No they will not directly interchange. Hyundai did not start using it's engines into the Kia Rio until late 2005 at the launch of the 3rd Gen Rio. The 1st (2001-2002) and 2nd (2003-2005) Kia Rio's use a variation of the Mazda B6 engine.

Why does the rear defogger not work on a 2001 Hyundai accent?

It is possible that the rear defogger does not work on the 2001 Hyundai Accent because the vehicle has a blown fuse or damaged wiring. The defogger might also not work because the wiring is disconnected.

What are the head bolt torque specs and sequence for a 3.8 Ford Windstar?

The information for a 1993 Sable 3.8 is in the below cited "Related Question".

Definitely worth double-checking those specs - try Autozone's online Chilton's repair linked below.

Here's for a 2001 Windstar 3.8:

Torque Sequence

-----------------------

Frt | 7 3 1 5 |

Of | 8 4 2 6 |

Engine -----------------------

Step 1 - Torque to 14 ft/lbs

Steps 2 - Torque to 29 ft/lbs

Steps 3 - Torque to 36 ft/lbs

Perform following 3 steps on each bolt, before moving to next bolt in sequence

1) loosen 2-3 turns

2) if long bolt: Torque to 30-37 ft/lbs if short bolt: Torque to 15-22 ft/lbs

3) turn 175-185 degrees

Proceed to next bolt in sequence

Recheck final torque in sequence
the torque is the especific tighten that the bolts need in a specifical sequence: in a 3.8 lt. is executed as follow: step1- 15ft-lb. step2- 29ft-lb. step3- 37ft-lb. and step4 loos each bolt 2 turns and tighten until last torque specificated and very important is do that in the specific sequence .(do not loose all the bolts at the same time) intake maniful side 7 3 1 5 8 4 2 6 exhaust maniful side I hope this help you to see the sequence .