0
Oldsmobile Ciera
Manufactured by General Motors from 1982 to 1996, the Ciera was a mid-size car and the best-selling model of Oldsmobile. It was offered in 2-door sedan, 4-door coupe and 4-door station wagon body styles.
697 Questions
On a 88 olds ciera Antenna motors never shuts off?
Cable inside the antenna is broken
Disconnect wiring to antenna or replace entire unit
Why won't your Car brake lights turn off?
in my 95 ciera the brake indicator switch was slightly out of alignment causing lights to stay on when in the relased position. i had to remove the wire harnes from the switch and turn it two complete turns in towards the brake arm. turning it too far will cause problems with the cruise control.
What do you need to bleed brakes on a 93 Oldsmobile cutlass ciera?
A 7/16" or 10mm open end wrench and a second person.
Jack up car, Remove wheel.. safety first, used jack stands.
1. Have someone in the driver seat push and hold the brake pedal down.
2. Use the wrench to open the bleeder valve on the caliper (front or rear) or wheel cylinder (rear). Brake fluid should squirt out with some air.
3. Close bleeder valve.
4. After valve is closed, tell second person to pump brake 2 or 3 times, and hold pedal down.
4. Repeat process until only brake fluid comes out.
5. Repeat for each wheel.
How do you adjust valves 3.1 1995 olds ciera?
There really is no adjustment... Tighten the rocker nut/bolt and that's it... Maybe you have other mechanical problems? Whats the problem?
Where are fuel injectors for Oldsmobile Alero?
dependsd upon what type of engine but they are usually very visible they are at the top of engine with small elect wire attached to each one not big wires like the sparkplugs
Ok. First you can't "turn on" a relay. It is either working or it isn't. "several electrical accessories in the vehicle use relays to transmit the electrical signal to the component. If the relay is defective. that component will not function properly." ( Haynes Repair Manual, General Motors 1988-2002, p12-5) Your fuel pump relay should be located under the hood in the fuse box on the right (passenger side) of the car. It is a black square approximately 1" by 1". Replace it if your fuel pump isn't working as a cheap method of elimination.
How difficult is it to replace the thermostat on a 1990 Cutlass Ciera with a 3300 engine?
It is quite easy to change the thermostat in your 1990 Cutlass. Remove the thermostat housing retaining bolts. Remove the thermostat from the housing. Reverse the process to install the new thermostat.
Where is the blinker fuses located on a 94 olds cutlass supreme?
Well, first of all, the bulb is going to go out *way* before the fuse itself. If your blinkers just stay steady, its a bulb.. if they don't come on at all, its probably a bulb, but just so you know, if you flip over the cover to your fuses, you should find a handy dandy little sticker, and it'll tell you the amps of each fuse, and what the fuse is for.
How do you replace the starter on a 1997 Aurora Oldsmobile?
. There may be minor differences in the 96-99 years, this is specifically for a '95. Hopefully it's close. 1: Open hood and remove plastic heat/noise shield from top of motor (4 plastic nuts) 2: On the passenger side of the engine, near the front valve cover, you will see a small box labeled "Battery +" in red letters. Pop that cover. This is the lead to the starter. If you don't want to have to pull the backseat for the battery just remove the nut and pull this wire. 3: Remove the silencer and intake tube from the airbox (the box itself can remain). 4: Label and remove the 4 front spark plug wires. I lay them down on the hood and hold them with the wiper. 5: Disconnect the TPS sensor (side of TB, away from passenger compartment) 6: On the '95, disconnect wiring to the Idle Air Motor (96-99 have it in the TB, different wire). 7: Disconnect the wiring look for the Fuel Injectors, it's down and slightly rear of the TB itself, large round plug. 8: Disconnect the fuel lines at the firewall. You can leave them on the fuel rail. 9: Undo coolant line from underneath the TB (spring clamp) Pull off and let drain out while you work. 10: Remove all vacuum lines from TB (one large on the side, 2 small up top, 1 or 2 more i forget). 11: Now is a good time to check the vacuum port on top of the TB. It just unclips. Mine had several cracks in it. 12: Remove EGR pipe from side of TB. It bends out of your way, but go easy on it. 13: NOW check to make sure all your vacuum lines and wiring it out of the way and not going to fight you as you move the intake out of the way. 14: If you havn't already, remove the 4 studs that are the supports for both the top cover, and the hold downs for the fuel rail. 15: Remove bolts for the intake. 10mm. I believe there is 4 of them per side. I know if you have had the fuel recall done that they re-locate the FPR to the front. Right over a bolt. Just use a short open-end wrench and you'll be fine. They're not tight. 16: Some of the bolts will come out, some may not. I had 2 or 3 that wouldn't come. That's fine just make sure you have them completely backed out. 17: This part is probably easiest with two people, but one should be able do it with not to much trouble. Grab the TB mouth and the end of the intake (where the pressure-relief door is) and lift straight up. The whole unit should come up. 18: Rotate the whole thing counter-clockwise. That's with the TB facing the passenger compartment and the pressure-door facing the front. 19: If you're like me, there will be tons of leaves and stuff down there, take this opportunity to vacuum it out. Also if you feel compelled, you could clean all the intake ports too. Take rags or paper towels or tape or SOMETHING and put it over the intake ports, don't want anything down there. 20: Remove the starter with the wires still attached, this is why you removed that B+ lead before hand, RIIIGHT? It's two 10mm bolts, plainly obvious. There isn't any hidden or anything. 21: Pull the starter back and up, and rest it on the valve cover. Use a 14mm socket for the main lead and a 8mm for the trigger lead. 22: Put the wires on the new starter first, then place it back into the car. 23: Installation is reverse of removal! Also, check to see how your intake gaskets are. Mine were OK, but it might be a good idea to replace them. I know there was a marking on manifold saying it was replaced at 14k miles. I hope this helps anyone, i know the dealer will want at least $500 to do this job, plus the starter. I priced a 2 year guarantee starter at $235, and the labor took me about 2 hours.
What is the oil capacity of gm 3.1 liter engine?
While owning a car, it is important to know the engines oil capacity. The oil capacity of this engine is 3.1 liters or about 5 quarts of engine oil with an oil filter change.
What code reader works on a 1994 Olds. Ciera 3.1 GM3123 for 1982 t0 1995 does not?
If Pin "B" is not present in the 12-pin connector, use the Actron SUPER AutoScanner CP9145 with a GM ALDL Cable CP9127 or use the Actron SUPER AutoScanner Kit CP9150. Either one will work on that OBD 1.5 system.
Simple answer is, that in sometime in your cars life, the windshield was replaced, and the windshield didnt get sealed properly. Call a local glass replacement office, and ask then if they can reseal your windshield, and how much its going to cost. Should be more than 50 bucks.
Where is the starter on a 1989 Oldsmobile Cutlass Ciera?
4 cylinder - try the front lower section of the engine behind radiator 6 cylinder lower rear section of engine Try to follow + battery cable
Where is the fuel pressure regulator located on a 87 olds cutlass ciera and how to change it?
Next to the trottle body. On the side. Buy one from store to see what's it looks like easy to change
Where is the flasher switch on a 1994 Oldsmobile Cutlass Ciera S 4 door?
The flasher switch for the 94 cutlass is not where you would think it would be it is behind and off to the side of the ashtray or below the radio. The above is accurate; getting to it is a little tricky. Open the glove box and remove the tether wire connection at the door by unscrewing the SHC screw with a T-15 Torx driver. This will expose 2 of the 4 fuse panel mounting screws. Use an 8mm socket to remove all four and wiggle the panel out. The flasher is behind and to the left in the harness itself, not on a terminal block. Use a straight blade screwdriver to gently pry the two prong connection from the unit (Mine was an OEM Wagner - bright yellow.) Additional Answer It depends if you're talking about the turn signal flasher or the emergency flasher. The emergency flasher is directly behind the glovebox. If you're referring to the turn signal flasher, I just replaced mine last night without having to mess with the fusebox or glovebox. It turns out that it was attached by a clip on the right side of the ashtray frame inside the dashboard. I took out the removable "cup" part of the ashtray, then removed the two upper and two lower ashtray frame screws. Next, I pulled the frame forward and disconnected the small ashtray light. The power wire for the cigarette lighter can stay attached. After I slide the frame out the rest of the way it was easy to get to and replace the flasher unit.
How do you solve the knocking engine caused by using E-85 gas?
Your auto was not designed to operate on E-85 fuel... Buy regular gasoline instead!
Where is the thermostat on a 1992 Oldsmobile cutlass ciera?
On the 3.3L V6 it is under the radiator cap.
How do you replace a front wheel bearing-hub assembly on 1994 Olds Ciera?
the same way you would replace any hub assembly, take the wheel off, take off any bolts that connect the hub to the driveshaft and then replace it
Where is the cooling fan relay located in 1991 Oldsmobile cutlass ciera?
The 1991 Oldsmobile Cutlass cooling fan relay switch can be found attached to the right side of the radiator housing. The cooling fan relay switch should be labeled as such.
How many Cutlass Supreme Convertibles were made by year in the 90's?
About 1500 of these beauties were made in total.
Where is the flasher on a 1990 Oldsmobile Cutlass?
the flasher is on the right side under the glove box.
Where is the turn signal flasher on a 1996 Olds Ciera?
This is Terry Donovan and I have answered my own question. On the 96 Ciera the turn signal flasher is behind the fuse box. The fuse box is in the glove box. Remove the four screws and take out the fuse assembly. Look in to the left and WALAHH. The hazard flasher on this car is under the passenger dash all the way to the right. Take out the right dash speaker and you can reach it. You may have to remove the glove box for this one too.
Where is the orifice tube located on a 1992 Oldsmobile Cutlass Ciera S?
The orifice tube is located in the high pressure line at the left-bottom of the condensor (which mounts in front of the radiator). Where the line exits at the left-bottom (this is driver's side) of the condensor you will find an inline connector. Above this connector you will notice three small dimples in the line - this is where the orifice tube is mounted. Break the line (carefully!) and remove the orifice tube with a pair of needle nose pliers. Begin removal by gently twisting the orifice tube to break its seal and extract. Be careful because these can be broken easily and any remaining portion in the line is of course more difficult to extract. Also, the line and its connector is aluminum. Typically the threads are very dry and extremely difficult to break loose. You MUST use a backup wrench along with the one used to loosen the connector and it will help by using some type of penetraing oil/lubricant. Be careful with this as it is easy to either twist the line itself (and ruin it) or pull the threads off the aluminum nut at the connection.
