0
Oldsmobile Cutlass Supreme
Manufactured by General Motors from 1966 to 1997, the Oldsmobile Cutlass Supreme was a mid-size car produced in five generations. Its fifth generation model was available in three body styles: 2-door convertible, 2-door coupe and 4-door sedan.
2,211 Questions
What would cause a 1991 Lebaron Convertible GTC 3.0 to stall or not start when it is raining?
Check your distributor cap, make sure your not getting moisture in it...lebaron and Chrysler 3.0 have a common problem with the screws on the dist. cap to be corroded and break off. quite possible this problem is as simple as replacing your dist cap.
What type of freon does a 1995 cutlass supreme use?
A 1995 Cutlass Supreme should use R12 freon. The fittings are different between R12 and R134 so that they can not be accidentally swapped.
Where is the thermostat on a 1995 Toyota 4runner?
Usually in a removable housing at the engine end of the upper radiator hose
it is located in the housing but on the lower radiator hose ,not the top hose as in other vehicles
Where are the spark plugs on a 1997 Oldsmobile cutlass supreme?
don't have my manuel how many spark plugs are there in a 1997 cutlass supreme oldsmobile. need to change them all v6 engine. what is the best brand to buy thank you
The positive crankcase ventilation valve (PCV) on a 1994 Oldsmobile Cutlass Supreme with the 3.4L is located on the left-front side (drivers) of the vehicle towards the firewall. The PCV will be located between two black hoses with appearing as a T-fitting. The OEM PCV is a AC Delco part# CV895C.
What is the stock tire size for a 1995 Olsmobile Cutlass Sierra?
185/75-14 Optional tire sizes: 205/60-15 205/55-16
How do you remove and install an ignition cylinder in a 1992 Delta Eighty-Eight Oldsmobile?
They are same special tools what u can order them from the net or maybe u can find them at autoparts, i have the same problem , but i just wait like that for a while i use the screwdriver :) .....Good Luck ... Evidently,you have lost your keys lol.With keys removal very easy,without can be pain,Hopefully you have already purchased the new cylinder.Instructions should come with cylinder.You will need a steering wheel puller,roughly cost is about 12 bucks.You might also need a set of star drives. Set aside the day for removal,should take roughly 3 hours if all goes right,but extra time helps so not to get frustraded.Phillips and flat heads,adjustable wrench or correct size for steering wheel nut.Put parts in order as taking off,hence the first parts should be farthest away from you. If it has a release hole,use a straightened out paper clip this is the best case scenario without key. If it has locking pin and cylinder needs to be in run position to depress pin.Heres where the fun begins, everywhere you read will say drill the pin.Dont,go to the hardware store and purchase 2 dremel cone grindstones.Use these with a drill and grind the pin.Using a drill bit will just tear up the soft metal around it.Trust me on the 2 grindstones,you will need 2.By now cylinder should move just a tad.you can tell if pin is holding it up or not.Your not done yet,take a 3/8s drill bit and drill dead center of key hole.Make sure you have new cylinder in hand so that you know if drilling into anything but cylinder.Cylinder should fall apart in about 3 pieces.Remove those pieces,kind of match up with new to make sure all is out.Figure at least an hour on drilling center of cylinder.Wipe inside out to remove debri,light oil new cylinder with 3 in one.Slip in and start up.Put everything back together. Good luck,sounds hard but after you finish it you will realize not to bad.
How do you remove thermostat valve from 3.3L V6 1989 Oldsmobile Cutlass Cruiser station wagon?
It's a bit tricky actually. I bought a Haynes manual, and the diagram within does not display this particular motor and so is pretty useless. The thermostat housing is located on the end of the top water hose mounted sideways on the top of the engine underneath the throttle body and right next to the junction of the exhast manifold and header. You will have to remove the air cleaner box for sure, but access is extremely restricted compared to the 3.1l.
Why is the Cutlass supreme low coolant light blinking?
First off, check your engine coolant tank. If it's low, then that's the problem. Put more coolant in. If it's at the correct level, then look to see if there's gunk buildup. Second, is your engine overheating? If the engine is not overheating, and there is gunk buildup in the coolant tank, then you may just need to clean the sensor. If there is no gunk in your tank, your coolant level is fine, and your engine is not overheating, then it may be a bad sensor, and you need to replace it.
What v8 motors will fit in a 1984 olds cutlass?
That all depends on what you mean by "fit". If it is originally an Olds motor, then any small block Olds will drop right in.
If it's a V-6 you are going to have to change frame mount locations to drop in any V-8. If it's originally a Chevy V-8 engine, then any small block Chevy will drop right in.
If you want to do a little fabricating just about any engine will fit in that car. I've seen big block Chevys in many of them. For this swap, you really have to watch the clearance around the A/C box....if so equipped.
counterfactual (14 letters) unsubstantial (13 letters) misconstrued (12 letters) My response to this question was counterfactually miscalculated, erroneous, fallaceous and unsubstantiated.
Where is the voltage regulator located on a 1972 Oldsmobile cutlass supreme?
The Volatge Regulator Is Inside The Alternator.
How do you replace the alternator on a 1985 Oldsmobile Cutlass Supreme?
find the tensioner pulley to release the belt. there should be two bolts on the top (one in front, one in rear) and one on the bottom rear ( this one is very tricky to get to).
It could be either one. However, it is well known that these years of V6 engines had weak intake manifold gaskets from the factory. You might just luck out and it'll be the intake gaskets. You could also do a compression and leak down test to check the head gaskets before tearing it that far down to only find out they were fine.
Fuse box location in GMC safari 1995?
A GMC Safari is one of the vehicles that installed their fuse boxes under the hood. To open it squeeze both sides.
Where is the thermostat on a 1993 Mazda mx 6?
UNDER HOOD, DRIVER SIDE, UPPER ENGINE AREA, ENGINE END OF UPPER RADIATOR HOSE, MOUNTED IN COOLANT OUTLET HOUSING
How do you change the heater blower motor in an olds cutlass ciera 1989?
unplug the blower motor (electrical) Unbolt the blower moter Remove the alternator Remove the top powersteering bracket bolt Loosen the lower powersteering bolt Pry the powersteering pump towards the front of the car as much as possible Have a freind pry the engine towards the front of the car while you rotate and turn the blower motor out of the housing. Caution do not bend the fins on the blower motor. Its a tight fit but will come out with the right angle
Brake lines for 1984 Oldsmobile cutlass?
be more specific, bleed, what kind, or crossreferences of other models..
Will 2000 - 2005 Chevy Impala wheels fit on the new 2006-2007 Impala?
Yes, it's the same size (minimal 16") and bolt pattern (5X115), as backspacing and offset. And some big size Pontiac, Oldmobile and Buick will fit too.
What is the firing order on a 3.4 Oldsmobile silhouette?
The firing order is 1,2,3,4,5,6. Front cylinders are 2,4,6 the rear 1,3,5 from left to right as you face the engine from the front.
Where is the keyless remote receiver located in a 1994 Oldsmobile cutlass?
On the inside of the rear quarter-panel drivers side, access through trunk
