0
Oldsmobile Cutlass Supreme
Manufactured by General Motors from 1966 to 1997, the Oldsmobile Cutlass Supreme was a mid-size car produced in five generations. Its fifth generation model was available in three body styles: 2-door convertible, 2-door coupe and 4-door sedan.
2,211 Questions
Is there a 1972 Oldsmobile cutlass cs map light on the mirror option?
Yes,
My 72 Olds Cutlass convertible came with the light option package which included a map light in the rear view mirror.
Why does my rear car tire shakes?
There are literally dozens of things that could cause this to happen, but whatever it is the shake will continue to get worse until its fixed. Usually these kinds of thing will wear a tire out prematurely too, so you may have to drop a little bit of money in the short term, but it will save you money in the long run
The forth wire is to ground the body of the dryer. The cord should have red, black, white, and green wires. Red and black are hot, the white is neutral, and green is ground. The red, white, black in that order or reversed, black white, red, should go in a row where they connect to the dryer with the green one probably above it. If the center neutral lug has a bond to the chassis remove it. You have a dedicated wire to replace it now.
What type of transmission is a 1983 Oldsmobile cutlass supreme v6?
More than likely a metric TH200. Maybe a TH350 if you're lucky.
Why wont my car start when i turn the key it sounds like it is going yo but doesnt?
A small arm operated by a mechanism , able to deliver a rapid adn contionuous fire of bullets as long as the trigger is pressed.
Yes
What should the oil pressure gauge read at idle and during acceleration in a 2004 Tahoe 5.3L?
between 35/60 psi.
How do you know if your water pump went out on a 1995 Acura Integra?
If it is leaking water, it is bad.
What are the timing marks for a 1997 Cadillac Catera?
The rear metal timing belt cover has a notch behind each of the camshafts. Use these notches to put the mark on the camshaft gear starting from passenger side with the #1 on the camshaft gear, then 2,3, & 4 in order. On the crankshaft you must remove the 6 bolt holding the pulley and remove pulley so that you may access the mark on the bottom gear. One you locate that mark that one should be aligned at 6 o'clock position with a recess on the front right underneath that gear. At this point cylinder #1 is at top dead center. If you had removed the timing Gears, Install the gear so the alignment pin on the cam is in the correct, numbered alignment slot on the cam gear, to prevent a 180 degree out cam timing.
Where is the thermostat located in a 1985 cutlass supreme?
Look at the engine end of the upper radiator hose in a removable housing
Where is the convertible top motor on a 1994 Cutlass Supreme Convertible?
the convert top motor is in the trunk behind the vinyl top collector or the vinyl top shoot. you cant miss it.
You own a 91 Chevy beretta the hood release cable is broken how can you open the hood?
Look up from behind the front bumper, in front of the radiator. You should see the end of the cable going the hood latch. Grab a section of it with a pair of locking pliers and PULL. The hood should open. Replace the cable so you won't need to do this again.
How do you go about disconnecting a water pump from a 1994 3.1 Oldsmobile Cutlass Supreme?
GO TO WWW.AUTOZONE.COM AND YOU'LL NEED TO PUT IN YOU CAR INFO AND WHAT NOT AND IT WILL TELL YOU HOW TO GO ABOUT REMOVIN THEN INSTALLING YOUR WATER PUMP, IT ALSO SHOW'S A PICTURE TO HELP YOU AS WELL. YOU OUT. GOOD LUCK.
New HeadlineCrack loose (don't remove) the water pump pulley bolts then use a 10 inch adjustable wrench and rotate the idler pulley arm CCW to relieve the tension on the belt. The tensioner arm has a boss on the casting that can be used to seat the wrench. I have seen some arms with a 3/8" square hole cast into the arm to accomodate a breaker bar drive instead of having a boss with flats. Relieving the tesnion will allow the belt to slip off the grooved pulley.Remove the belt, remove the pulley nuts. This will allow access to the pump mounting bolts. I think there are 3 or 4 10mmm bolts.
What is a P0401 code on a Oldsmobile cutlass supreme?
Trouble code P0401 means:Exhaust gas recirculation flow insufficient detected
How do you replace the exterior door handles on a 1994 Oldsmobile Cutlass Supreme?
You need to pop the whole plate off. The part is fairly expensive, but I had the handle on mine sheer off during off during the winter, and I needed to get underneath the entire door handle and pop it off. It comes off and comes back together fairly easily. Check on eBay, the complete door handle assemblies are selling for between $20 - $30.
Google the manufacturer's name.
k
Quadrajets have a maximum airflow of from 750-800 cfm. Because the secondary side of the carb opens according to the airflow requirements of the engine, the same carburetor size can be used on a large range of engine sizes. The basic 750 cfm quadrajet casting is used from 231 CID to over 400 CID - the big secondary air valves open only as the engine breathes. For example, on a mild 350 Chevy the air valve will never open all the way - because the motor can't use more than 600 cfm or so. Your 307 will simply not require the full use of the secondary air valves, at no cost of engine power however.
-DB, 1969 Hugger Orange Camaro
What causes transmission fluid to leak on a 1970 Cutlass Oldsmobile?
A transmission fluid leak means that the plug may need to be replace, or the seal or gasket may need to be replace. As it could be caused by a work seal, or gasket, or a loose plug.
How do you install shocks on a 1987 olds cutlass supreme?
this job is so easy im wondering if your seriouse ...but here goes the front shocks are accessible through the top its only one nut that needs to be removed there the botttom at the a-arm there are two that need to be removed jack the car up pull it out same for other side then reverse process for installation the back you might want to jack it up cus youd have to get under the car to see the top of the shock and the nuts that connect it to the car remove them as well as the bolt that connects it to the mount on the axle then reverse the process for installation
