0
Toyota Sequoia
The Sequoia is a full-size sport utility vehicle (SUV) manufactured by Toyota Motor Corporation from 2000 to the present. This model is sold exclusively in the Middle East, the US, Puerto Rico, Mexico, Chile and Canada.
1,008 Questions
Firing diagram for 1987 ford ranger 2.9?
The spark plug firing order is ( 1 - 4 - 2 - 5 - 3 - 6 ) The distributor rotor turns CLOCKWISE ( 1 - 4 - 2 - 5 - 3 - 6 ) The marked # 1 position on the distributor cap faces towards the firewall and slightly towards the passenger side The engine cylinders / spark plugs are numbered : passenger side of engine , front to rear , 1 , 2 , 3 and drivers side of engine , front to rear , 4 , 5 , 6
Does a 1998 Vauxhall Vectra 2.0 DTi LS have a timing belt or timing chain?
For Vectra 2.0Ltr Dti With an engine code of X20DTH A chain is fitted
Why should the timing belt be changed on a Toyota Sequoia at 90000?
It must be changed every 100,000 miles on a 2004 and newer. On a 2003 and older it must be changed every 90,000 miles.
What is the maximum towing capacity of the 2013 Toyota Sequoia?
The maximum tosing capacity of the 2013 Toyota Sequoia is 7400 lbs..
How do you program a keyless entry fob for a Toyota Avalon -1997 XL?
This is what we did on my buddy Toyota. Put the key in turn it to run 5 times with in 10 seconds. Push any button on the remote. Your car will lock and unlock, if you have more than 1 remote do the same steps, and after you push any button on the 1st remote push any button on the second remote with in 5 seconds, again your car will lock and unlock.
I found this for 1998 Avalon... but it did not work for my 1997 Avalon XLS. The above did not work either.
1. Start with key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.
2. Insert key into ignition (Do not turn) and pull it out.
3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.
4. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.
5. Within 3 seconds the power door locks should cycle automatically indicating successful entry
into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks
should cycle once indicating successful programming. If the door locks don't cycle or
cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.
7. Close drivers door.
How do you change the tail light bulb in a '95 Geo Tracker?
This is easy. All you need is a Philips head screw driver. There are two screws at the bottom of the plastic lense. unscrew them and gently pull the entire assembly out. Then you can turn the bulb connectors on the inside to release the bulb and replace it. Sometime the connectors are tough or stuck, but they twist about 90 degrees and then release. Then reassemble.
How do you change the bulbs in the top tail light of a 1996 Nissan Altima?
open your trunk to get access to your tail light, unscrew some plastic snap-on-screws to get to the panel that holds all your tail lights move the fabric uncling the panel CAREFULLY and change your burn bulbs
How do you change the fuel filter on a 2006 Toyota Sequoia?
Does the 2006 Toyota sequoia have a fuel filter
What is the drivetrain warranty on the 2011 Toyota Sequoia?
The drivetrain warranty of the 2011 Toyota Sequoia is 5 yr./ 60000 mi..
What type of transmission fluid is used in a 2002 Toyota Sequoia and how much?
i need to know what year to correctly answer you, there are 2 possibilities
Does the 1990 Nissan Micra have a timing belt or timing chain?
K10 micra is belt driven! 1000 & 1200cc's (1982- 1993)
How do you remove front door panels on a 96 Grand Prix SE to replace speakers?
well you have to remove all the screws that you can see, once you do that theres four that you cannot see, ones in the top of the panel under the plastic where the seat belt goes in not all of the plastic just the middle cover its cliped in, anoth(pops right off with a flat head screw driver), then the gray plastic comes off when you depress the clips at the top and bottom and it should pop off there is a screw under that, another of the hidden screws is a torx im not sure of the size because the screw driver I used did not say but I think its around 20? its located in the bottom right of the handle where the far top Right of the speaker meets the handle, this screw is at an angle, you'll also have to remove your window button panel held with 2 smaller torx clearly visible, once you remove that there is a rather large torx screw under that you should find it quickly its not that hidden, after you remove all the screws the panel will still e rather tight from the clips you'll have to carefully remove these from the panel without breaking the panel, they wont simply slide off you'll have to replace these if you want factory tightness you can find some at pepboys or you can just forget about them and just screw the panel back on making it easier to remove in the future, also be careful not to over tighten any thing or else you'll strip the holes and you'll be in a world of trouble,
good luck!
when I answered this i forgot to put I did not re use the clips but I added an extra screw to the bottom of the panel for a more secure fit.
What kind of fuel does the 2004 Toyota Sequoia use?
The 2004 Toyota Sequoia runs on regular unleaded.
Why wont the back hatch open on a 2006 Toyota Sequoia even though its unlocked?
There is a button you have to push under the steering wheel column. This button is located on the bottom trim about 4-6 inches from the hood release.
How do you reset maint-req light on a 2005 Toyota sequoia?
turn key to on without cranking the engine then press the trip meter lever for a few seconds until the meter reads zero
How many quarts of oil needed for a 2002 Toyota tundra oil change?
A 2001 Toyota Sequoia with the V8 needs 6.5 quarts. Possibly the same engine???
How to get back open if it won't open?
We have had this happen too. Occassionally we have turned the key the opposite direction, opening the back window. Once the window is closed the door can be unlocked and opened.
Can anybody help you out I need a diagram of the firing order for a 1979 Lincoln continental 400?
The firing order is 1-3-7-2-6-5-4-8 Distributor rotates counter clockwise. Cylinder locations are Passenger side front to rear, 1-2-3-4 Drivers side front to rear 5-6-7-8.
Does the 2000 Toyota 4Runner have a cabin air filter?
WalMart now sells Fram cabin air filters. Check the Fram application catalog in the filter section to see if the 2000 4runner is listed. Parts houses can also tell you.
What kind of fuel does the 2001 Toyota Sequoia use?
The 2001 Toyota Sequoia runs on regular unleaded.
I have heard that at highway speed (75), you will be going ~ 2 MPH faster than it shows
How do you change tail light bulb on a Mazda protege?
On the 95-98. Open the trunk. The screws (2) are just inside the trunk. After you remove them, very carefully push outward in the lens. The lens has a pin on the outer side that sticks into the car body. This pin can stick, so be very careful not to break something.
On my 2002 Protege ES, the process is a bit different
There are two plastic retainer do-hickeys on the hard that are made up of an inner circle and outer ring. Both of these are easily visible.
They are removed by first loosening the inner circle (probably moves back about 1cm), and then the whole do-hickey can be removed by gently prying the outer rings.
The hard vinyl still feels attached, so you can move it/lift it by hand until it moves over the rear release latch. This gives you enough room to operate.
The hard cloth (who's edge is covered by the vinyl) has two of those plastic retainer do-hickeys. Remove them too. Then you can access the back of the assembly/sheet metal.
Then there are three brass-ish long screws with 10mm nuts. Remove those three nuts, and you can pull out the tail light assembly.
