0
Buick Rendezvous
This category covers questions about the Buick Rendezvous, a mid-sized crossover SUV that was manufactured by General Motors and sold through its Buick division. The Rendezvous was produced from 2001-2007 and was succeeded by the Buick Enclave.
1,007 Questions
How do you change the tail light of a Buick Rendezvous?
Open rear hatch and remove 2 screws that hold tailight on and pull out
How do you remove the headlight assembly on a 2003 buick rendezvous?
From the open hood there is a slide clip that has to be lifted up to release the inboard part of the HL assembly. Also, remove the wing bolt that holds the other end of the assembly. (farthest from the clip) Remove the assembly by pulling it straight forward. There is a ball/socket retainer that can hang on pretty tight. I had to pull mine quite hard to get it out. Mine had a gray safety clip that had to be removed in order to disconnect the electrical plug. Good Luck.
Where is the Fuse for the Power Outlet for a 2006 Jeep Liberty?
There are 2 fuse panels located on the 06 liberty, One under the hood and another on the drivers side of the dashboard, you will notice a long slender panel when you open the drivers door with a notch on the bottom of it, once you pop that panel out you will see the fuses, Fuse number 16 which should have a yellow 20 amp fuse in it is for the rear power outlet.
How do you replace Mazda b2200 door latch?
I just replaced the door latch mechanism inside the door on a Mazda B2200. It was not too difficult to do as long as you have some mechanical ability.
Trouble Symptoms: The door would not open using either the latch outside the door or the release latch on the inside of the door.
The resolution to the problem is replacing a small 1/4" spring on the latch mechanism inside the door. Unfortunately Mazda will NOT sell just the spring. You must buy the whole latch assembly (for approximately $120). In my case, I refuse to pay that much!! I went to a junk yard in Houston and purchased the the latch assembly for $35.
To start you must remove the inside door cover. First remove the two screws holding the arm rest. The armrest should just pull off or fall off when the second screw is removed. Then remove the window rollup and rolldown handle. To do this push in the panel behind the knob then you will see a spring C-clip holding the handle onto the handle shaft. Pry off the clip (be careful as this is spring loaded and flys off as it comes off so it is easy to lose). Once it is off the knob and the back plate should slide off the shaft.
Now remove the screw holding the inside door latch. Unscrew the screw and pull out the latch. You will see that it is attached to a metal rod. There is a plastic fitting holding the "L" shaped end of the rod on the latch. Pry off the plastic part of the fitting that is on the longer part of the rod. The pull the "L" part out of the latch. The latch should now be free to remove from the door.
Now it is a matter of putting a screw driver between the leather door cover and the metal door. Pry outward toward you. There a plastic snap fittings that pop loose as you pry. Try to pry near the fittings so that they do not pull though the panel. Once they are all loose (about 10 or 12) the panel should lift up towards the top of the door. (Might take a tap or two with the palm of your hand.) If it does not come off, check for another plastic snap fitting still holding the door panel on. Take off panel. Peel back plastic insulator from top left corner near the push button lock. Look inside the door and you will see the latch mechanism. There will be four rods attached to the mechanism. (Kinda looks like spagetti and way to complicated, but trust me they are bent so that it is fairly easy to put them back together.)
Look inside the door past the latch mechanism and you will see 2 10mm nuts. These nuts hold the outside door latch on. I took these off so the the latch was looser in the door and easier to move. I then remove the 3 Phillips screws that were in the door jam. This releases the door latch mechanism, however the mechanism is still held in place by the window rail which is also a 10 mm bolt in the door jam. Once this is removed the rail comes loose in the door as does the latch. I then removed the plastic fittings on the other two rods, one for the keylock, one for the pushbutton lock. The last rod is the rod between the outside latch and the latch mechanism inside the door. This MUST be unscrewed from the outside latch as there are no plastic fittings. This was done for security of the vehicle. One the latch is loose inside the door just push the rod so that the rod pushes out the outside door latch -- then unscrew it. The installation is the reverse of these steps. I choose to replace the tiny spring from then salvaged latch on my old latch, however you can either replace the entire latch or just the spring. REMEMBER there is a difference between the drivers side latch and the passenger side latch so specify accordingly.
What kind of oil filter does a 2003 buick rendezvous use?
lt uses a spin on filter, a very popular one that fits a lot of GM vehicles.
Napa part number 1040 or 21040 for the less expensive one.
Does the whole window regulator need to be replaced if it breaks and the window falls into the door?
I posted this because its a very common problem with these cars. the window rides on the cable with two plastic clips after years these clips will break it starts if when the window is down and you slam the door you can hear the window rattle, and when you roll it up the window goes up crooked or makes a clicking type sound. when the clips break the window will fall into the door. the dealership says you must replace the whole
assembly at around 250 dollars and that is not true. you can buy just the clips and fix it yourself. the clip part numbers are 15286776, 15286777 there is a right and left side on the window and these fit passenger or driver side. They run roughly 25-30 dollars each but alot better than 250. i found mine at a Chevrolet dealer. I have yet to install them but have read numerous post that they are a breeze to install just takes time. I hope this helps someone out and good luck :)
I have a 2002 buick rendezvous and my fans are not working?
I'm assuming cooling (rad) fans? Try tapping the fan motor housing to see if it will start. You can try unplugging the temperature sensor and see if the fans come on. Also you can try running 2 jumper wires to the fan plug from the battery and power it up directly to see if it works. Usual causes are a bad relay, temp sensor, or fan motor. Could also be an electrical (wiring/ground/ecm) issue.
Where is the bcm on a 97 cavalier?
The location of the BCM on a '97 Cavalier can vary based on the model. Many of them are just left of the hedge pillar and below the instrument panel. Some are above the instrument panel.
Which fuse controls the rear wiper on a 2003 4 runner?
There is a schematic on the inside of the fuse box cover. It is the second row down and three in from the right side. It's a 15amp fuse.
Where is the coolant temp sensor for a 1999 jeep grand cheerkee?
right a bove the power steering pump
Where is the coolant temp sensor on a 1993 Saturn sc2?
Your Saturn Twin cam engine actually has two temp sensors on it. They are both located on the right side of the cylinder head ( right side as if you are looking at the motor) mounted just under the valve cover line. They are small 2 wire pinch type connectors and are simple to replace. The one closest to the water inlet is the sensor that controls your gauge on the dashboard. the 2nd sensor just behind that controls the computer and your engine fans.
Where is the bulb for the instrument panel light in a 1995 Acura Legend?
You hav to remove the inst. cluster and them disassemble it (just remove the back plate) and you will find the bulb in there.
How do you replace the headlight bulb in a 1994 xjs convertable?
Inside the wheel well there is a small cover plate with 2 plastic screws which must be turned a quarter turn. The plate then comes out. Pull the plug off the back of the bulb. There is then a plastic collar which must be turned counter clockwise. To install, do the same in reverse.
How do you replace the headlights and bulb on a 1996 Dodge 2500 truck?
lift hood look at back of light threr is a twist lock simply twist to remove replace bulb and reinstall
If the bootlid seal itself is ok,then favourites would be rear lamp clusters and displaced grommets for tailgate wiring to wiper/lock relay etc. Best to get yourself shut in the boot witha torch.Have a helper,gently hose down the likely spots.
What does the ait sensor control?
It controls nothing. It sends a signal to the ECU based on the Ait Intake Temperture. The ECU uses this to determine the best fuel/air mixture.
How do you replace the passenger side mirror insert only on a 2004 Buick Rendezvous?
If your only replacing the glass, it should just pop out. You can use your hands or even a flat head screw driver. The new glass should just pop in if you put some pressure on it. Hope this helps!
Where is the backup sensor on a Buick rendezvous?
The backup sensors are located in the rear bumper. The four circles on the bumper.
What are the safety features on the Buick rendezvous?
Safety features on the Buick Rendevous include airbags, anti-lock breaks and child safety locks. The child seats also have air bags.
How do you replace the blower fan resistor on a 2003 buick rendezvous?
where is the switch resistor on 2003 buick
How do you replace clips on window regulator 2003 buick rendezvous?
Take your door panel off and replace them...
Oxygen sensor location on 2003 Buick rendezvous cx?
There are two. The first one sits in the exhaust manifold of the engine, right between the engine and the firewall. This would be Bank 1, Sensor 1.The second is located on the exhaust tube, right after the catalytic converter. This would be Bank 1, Sensor 2.
The second is easiest to get to and replace. The first one is by far the hardest and requires you to get at it from underneath the vehicle and absolutely requires you to have the vehicle on a lift or safely have the front half of the vehicle on jacks.
I'm a rotund individual and I also needed to have the car jacked for the 2nd sensor.
One other suggestion, make sure when you rent or buy your O2 sensor tool, it is for the size ratchet you have (3/8, 1/4, 1/2 etc). The one the store gave us to use was a 1/2, and I only had 3/8 and 1/4. I finally spent $13 for the GM O2 tool for 3/8...much easier.
How do you remove an instrument cluster on a 1986 volkswagen?
you are going to have to remove the panel they are in and disconnect the wires and either put the new panel up or if you have the old one put that back up. hopefully that will help
Iat sensor location Audi A3 1997?
The yaw sensor is attached to the steering wheel column under the driver's left knee clipped within a bracket together with the pitch sensor. Both measure acceleration in either the lateral (yaw) or forward (pitch) directions and are used for the electronic stability programme (ESP) system. The yaw sensor is attached to the steering wheel column under the driver's left knee clipped within a bracket together with the pitch sensor. Both measure acceleration in either the lateral (yaw) or forward (pitch) directions and are used for the electronic stability programme (ESP) system.
