0
Chevy Beretta
This category covers questions about the Chevrolet Beretta, a compact sedan manufactured by General Motors and sold through its Chevrolet division. The Beretta went into production in 1987 and was discontinued in 1996, succeeded by the Chevrolet Malibu.
665 Questions
Can oil leak from the starter on a 1995 Chevy Beretta 3.1?
No, oil doesn't come out of the starter, either your distributor plug is leaking or you are leaking oil out of your front valve cover.
What is the individual cylinder compression for a Chevy 283 engine?
When it was new it had 150 PSI. per cylinder
What is the firing order for a Chevy Beretta 2.8L?
clyinders go from drivebelt to transaxle end, front by radiator 2 4 6, rear side 1 3 5, firing order is 1 2 3 4 5 6, hope this helps you wolverine
How do you reset the check engine light on a 1996 Chevy beretta?
Either unplug the battery for 10 minutes, or go to your local auto store (Orielly or Auto Zone) and borrow their scanner to clear the codes. Ask if you require assistance.
How do you disable the daytime running lights on a '96 Chevy Beretta?
on the emergancy brake lever there is an electrical switch, just unplug it they will go off and your fog lights will still work.
How do you change an Oxygen sensor on a 1995 Chevrolet Beretta?
It will require a special socket with a slot down the side so as not to damage the wiring. It may be cheaper to have a shop do it as the sensors do not go bad very often.
the only place to get that would be a g.m. dealership.
Where is the engine block drain plug located on a 1996 Chevy Beretta Z26 besides just on the bottom?
A 96 Chevy Beretta Z26 has a 3100 V6 engine. The oil drain is located on the bottom of the oil pan, on a slight angle pointing down and towards the rear.
What does an ABS light mean on a 1994 Chevy beretta?
anti lock brake system light might mean a bad brake sensor must be replaced
What are the torque bolt specifications when changing a head gasket on a 1995 22 Chevy Beretta?
14 ft lbs per bold but tighten in a zig zag pattern or you will crack the aluminum.
Do A compression test and a leakdown test too, This will tell you if you have A internal leak. The compression and leak numbers are not nearly as critical as the numbers being within 20% of each other across all cylinders.
Where is the temperature sending unit for a 95 Chevy beretta?
The temperature sending unit for a 1995 Chevy Beretta is on the front of the engine. It is between the front of the engine and the radiator inlet/outlet.
How do you fix a water leak coming from under the dash in a 1995 Chevrolet Beretta?
You will need to replace the heater core located in the heater housing on the passenger side under the dashboard. If you need to wait to do repairs you can disconnect the two hoses as they enter the firewall in the engine compartment and connect them together with the appropriate sized barbed union connector and hose clamps.
How do you remove the backseat of a Chevy beretta?
On a 96 beretta there are 2 bolts just under the front edge of the seat. Then after you remove the seat bottom there are 2 torx bolts (don't remember the size)holding the seat back and seat belts. After you remove the 2 torx bolts then you pull the seat back up to unhook the top of the seat back. torx T50
Removing the engine from a 1994 Chevy Beretta- does it come out the top or the bottom of the car?
It comes out the top.
How do you replace an egr valve on a 1995 Chevrolet Beretta 3.1 liter V6?
#1 Are you replacing the entire unit or just one of the three solenoids ? Best to change all at once. It's held on by two 10mm bolts. And you should always change the seals when ever you loosen the valve or you may wind up with an exhaust leak. And since there are some plastic tubing nearby you need to be careful they don't get too close or you'll melt them.
#2 , If you have an EGR code it is very very possible that it is a pluggage (carbon) problem for my 95 Beretta 3.1 has done this several times first remove the rubber boot that is between the air filter and throttle body then remove the throttle body then remove the bolts holding down the EGR and lift it out of the way look for the small tunnel like hole that runs from the EGR into the intake you can see one side by looking right behind where the throttle body was removed from on the right hand side wall you will have to find something to dig out the little tunnel so that the EGR can sense the flow again and your check engine light will stay off also clear the light by disconnecting the negative on your battery for a few minutes.
You replaced the flasher relay but the turn signals still don't work at all Hazards work fine Why?
on the Chevy beretta there are 2 flashers one is right next to the steering column to the behind the plastic dash piece,this is your turn signal flasher replace it and your signals should work.
Are a 1994 beretta parts interchangeable with a 1990 beretta?
drive train is not able to be used as are the wiring harness and ecm, most of the other parts are interchangable. These include brakes suspension and body parts... i.e. seats and interior...loosenut...
Where is a 94 Chevy beretta z26 voltage regulator?
The regulator on a 1994 Chevy is inside the alternator.
i am having the exact same issue all of a sudden. mine's a 90. Mine will turn off, but only after fighting with it. one of the guys at the repair shop i went to told me that sometimes, if you mess with your tilt steering while turning the switch, it can help unstick it. i don't know.. they tried mine out several times while there and the dang thing worked fine every time.. ughh.. from what I've read so far, if the car has tilt steering, you need a special tool to get in there and remove it. it would be helpful to get a chiltons or haynes manual, they are usually real good on diagrams, instructions..
good luck!!
