0
Chevy Blazer
The Chevy Blazer may refer to any of the sport utility vehicles manufactured by the Detroit-based automaker General Motors Company. Some of the popular Blazer models produced by the company are the TrailBlazer, the S-10 Blazer and the K5 Blazer.
5,824 Questions
How do you install a shifter cable on 1997 blazer?
The 1997 Chevy Blazer shifter cable will have swivel nuts on each end of the cable. Connect the shifter cable and turn the swivel nuts to the right to install the shifter cable.
There is an easy fix kit called the "HeaterTreater" that is available on eBay and at heatertreater.net. This fix is all-inclusive, easy to install, does not require removal of the dash, and only takes about 45 minutes. It cover Ford Rangers from 96'-04'
AnswerIf you recently purchased this vehicle I would check to make sure no one has by-passed the heater core. I once had a Nissian that someone did that on because the heater core had a leak. Didn't know that till I hooked up. As to the Fan if the Fuse is a Knowngood fuse, then check the switch you will need to remove it and have it tested to see if it is any good. You may also have to repair the fan, if everything else is "working" I've had to replace the brushs in a couple before.Good Luck
AnswerIf the fan is not running, then it is either a blown fuse, defective blower motor speed control switch, bad blower motor resistor pack, or a defective blower motor.Where can you find an exploded view of the engine in a 1999 Chevy blazer?
any of the DIY auto repair manuals will usually show an exploded view of the engine.
How do you engage or what are the steps to engage 4 wheel drive on a 2000 Chevy blazer LS?
put it into four wheel drive I have a 99, the best way is to go forward about 6 to 8 feet, DO NOT BACK UP. or it will not go in to 4 weel drive and many time will not move.
Is there a reoccuring problem with the heater core in an 2000 s10 blazer?
Problem is that the heater core is the highest point in the cooling system. being a closed system any air that enters is trapped in the heater core. Result, no heat.
Recommended repair is to back flush heater core, refill cooling system making sure all air is released from the heater core. Replacement of the radiator cap at the time of repair is recommended.
Where to buy K5 Blazer Removable top andor bolts windows etc?
LMCtruck.com
Hi, I tried LMC but they dont have the chrome bolts with the captive washer.
My 1983 takes 10 short bolts and 6 that attach to the back of the cab.
I have to special order from TAcoma Screw, I hope they have em.
What do you do if the key wont come out of the ignition on a 4Runner?
I know this has been awhile so you probably have it fixed but Ill take a stab at it anyway. The locking mechanism can fail and the only thing you can do is call a lock smith. But, before you do look at 2 things. Several models have a lock button on the steering column that you must push to release the key. This can loose a pin and not work. Also it needs to be in the off position. You might need to remove the cover to see it. Some have an ACC position is is all the way counter clock wise. You need to be in the off position one click in the clockwise direction to get the key out. Lastly if the steering column is locked it can have pressure on the key not allowing it to move into the right position to come out. Just apply a turning force against the wheel and then try and turn it.
Can you replace just one rod and piston without replacing all of them?
Yes. Ideally it would be the same style and weight as the old one.
How good is a Chevy Blazer 4.3?
With regular maintenence the 4.3L is a good engine, good for at least 200K.
I have a 1998 Chevy Blazer with the same problem I traced the stop light wires back to the turn signal assembly. By taking the steering column plastic off you use a torx bit and a pair of vise grips to get the bolts out of the turn signal assembly. Otherwise GM says you need to pull the steering wheel . They still recommend you pull the airbag fuse. I pulled the fuse and disconnected the battery. I found a slightly melted connector behind wiring connection point. With a replacement turn signal assembly the brake lights now work. Be sure to find a aftermarket or salvage yard switch due to GM wanting alot of money for OEM.
Is there a factory repair manual for a 1987 Mercedes sdl 300?
yes,,,,,,most chain parts stores offer haynes shop manuals for alot of makes and models
actually haynes doesnt make one for that model i just checked...bummer huh...however you can get CD ROM version... at mercedesmanuals.com
Where is the ECT sensor located on S10 4.3l engine?
Don't know what year you have but on a 02 S10 4.3L engine it is located on the drivers side of the engine between spark plugs #3 & #5.
What needs to be done when check engine light comes on in your 1990 Oldsmobile 88 Royale?
Take it to a mechanic who will use a computer to read a problem code generated by the car's computer. He will repair the problem and reset the light.
Plain English problem codes are not used to encourage car owners to take their cars to the dealership for repair. However, any competent mechanic will have the handheld computer required to read the codes.
AnswerPull the codes from the computer, match the code to the troubleshooting procedure, follow the procedure to find the source. Repair the source, light will go out if that was the only problem. There are "monitors" or self tests the computer runs the car through a drive cycle, if a problem occurs, it may not run all of the self tests until that problem is taken care. Therefore, another problem may exist. It is emission related. OR hook up a scanner that is capable of clearing codes, and hope that none are still active.Having a problem with switching a 1998 Chevy Blazer from 4 wheel low back to 2 wheel high drive?
You need to come to a compleat stop, then back up 3-5 Feet stop then pull shifter
back into 2 high. LEAVE TRANSMISSION IN DRIVE.
How do you get in 99 blazer keys locked in?
We can't publish an answer to this, as this is something which could facilitate illegal acts, even though I don't doubt you have no such intent. As a mechanic and a Blazer owner, I can help you with this, but you'll have to email me at the address listed on my bio page.
How do you change an idler arm on a 1998 Chevy blazer?
Remove the nut holding the idler arm to the center link. Separate the joint with a "pickle fork". Remove the two bolts and nuts from the frame end of the idler arm. Remove idler arm.
Sounds like you may have a vacuum leak- check under the hood and under dash area
How do you replace the alternator on a 2000 Chevy Blazer?
There is a pulley directly underneath your alternator that has a nut on the back of it. You'll need a wrench to put on it and push down to get slack on the belt. After removing the belt there are three bolts (two in the front and one on the back) that need to be removed. Then disconnect the wire harness and you may need something to pry the alternator out of the bracket and that's it.
How do you know if spider injection is bad on a 95 s10 blazer?
I just paid $111.00 to the local Chevy dealer for a diagnostic, the reason I went to them was because I would get a check engine light for a few days then it would go away. I also am having the hardest time starting it in the morning if it sits off for a day or so.. I would open and close the ignition about 5 times before attempting to crank it, and that would normally start it. They estimated almost $1200.00 to replace the spider injectors and the appropriate seals to put it all back together..
