0
Chevy Cheyenne
Launched in 2003 at the North American International Auto Show, Chevy Cheyenne is a concept car manufactured by General Motor’s Chevrolet brand. It features innovative technology not used in any vehicle yet such as its unique cargo bed and side access doors.
1,327 Questions
Single exhaust? Look before and after the converter. O2 sensors measure oxygen content before and after flow through the converter.
answerThe oxygen sensor is a spark plug shaped device that is screwed into the exhaust manifold. Answer:There is one sensor located before the cat convertor. It will be a 3 wire sensor.How do you replace the factory stereo on a 1993 Chevy Cheyenne?
What you need to acces is the factory amp/control for the radio which is under the dash right and above the gas pedal. Wire your radio harness and get your antenna adaptor. Unbolt and remove the factory amp and using the harness you unplugged, plug that into your nes harness and plug your new antenna adaptor to the mini gm antenna. remove the center panel between the cluster hump and glove box. pull the wires up from the bottom left of the hole in the dash. Take the new dash kit and put in the cage from your radio, put the a/c vents in the new dash kit, remove the two clips from the factory trim piece and put them on the back bottom edges of the new dash kit to hold in the bottom. Now plug in the harness and antenna, slide the radio in the kit and place the dash kit in the hole, top in first and push the bottom in. TAH-DAH new radio, and replace the speakers while you are at it you should have 4 4"x6" speakers.
Can you swap a 454 engine in a 1988 Chevy pickup with a 350 engine?
Yes. The exhaust is different, and you'll need a bigger radiator.
What was the first year seatbelts were installed in a Chevy truck?
What was the first year seatbelts were installed in a chevy truck?
How do you replace the inside drivers door handle on a 97 Chevy Silverado with power lockswindows?
2. Take the plastic frame off and away from the door handle. Do this by locating the plastic catches, push them in and down.
3. Take out the two screws inside the door grip.
4. Slide the tool to lossen the door panel to each of the plastic keepers and pop them out.
5. Do the same for the triangular piece above the door panel towards the front of the door.
6. Wiggle the door panel up and out. The electrical plug ins may keep the door panel too close to the door to work on the handle, use discreting if and when taking the wiring off.
7. Drill out the rivit holding the door handle in place. Slide the door handle forward toward the front of the door. Use needle nose, or whatever you can, to push out and release the two (2) rods connected to the handle. Now take out the door handle.
8. Do the same backwards to replace the door handle, you may want to use whatever you want in place of the rivit. A screw, tapped threads and bolted, etc. will all work.
I don't know who did the below, but it was difficult for me to follow! Not discreptive enough for me!!!
Need a rivet gun and rivets. Remove inside door panel...(need to remove a few screws. Panel is attached by plastic rivets so pull hard but gentle. Start from bottom and work around and up. Then slide it up to remove. I don't know if your door will have it but you might need to remove a metal plate (hexscrews) Now it gets a little tricky to explain. You'll see a thin metal wire attached to the door handle with a plastic lock nut (needle nose pliers to remove. You might also need a drill to drill out the rivets holding the handle. Reattach the handle to the wire BEFORE replacing the rivets. Then work yourself back to installing the door panel.I just did this a few weeks ago with power locks and windows. email me at candyman72101@hotmail.com if you have questions
What are the torque specs for head bolts on a 1992 Chevrolet 5.7L?
Cylinder Head bolts 65 ft/lbs=Intake Manifold bolts 30 ft/lbs==Exhaust Manifold bolts 25 ft/lbs=
Internal leakage on the spyder?
answercheck the firing order Turn the engine using a socket wrench on the large bolt on the front of the crankshaft pulley. Place a finger near the No. 1 spark plug hole and turn the crankshaft until the piston reaches Top Dead Center (TDC). As the engine approaches TDC, you will feel air being expelled by the No. 1 cylinder. If the position is not being met, turn the engine another full turn (360 degree). Once the engine's position is correct, install the spark plug. check the rotor location and start #1 plug wire where the rotor is pointing the firing order is 1-6-5-4-3-2 and the distributer turns clockwise answerI doubt it's the order, because I have a '91 and the only I had with it fuel wise was a loose wire on top of the tank 'cause of the bumpy roads, I live in Hawaii so,anyway, so check that too. It also could be a clogged fuel filter or line like I said a loose connection on your fuel pump or the pump itself could be dead. You never know, dodo happens.Why does my car die when I put it in reverse?
Sometimes the torquconverter can fail causing the engin to stall. In reverse it lock in full torqu. In fwd gears it slips. This is only one idea.
Where is the air intake sensor on a 1995 Chevy C1500 with a 350?
95 models did not use a air intake sensor.
What kind of transmission fluid does 1991 Chevy 2500 5 speed use?
Assuming it is a 5.7L I found this article in Alldata's TSBs
"5 speed manual transmission requires the use of a special synthetic lubricant . This special lubricant is required to reduce transmission internal operating temperatures. The synthetic lubricant does not require periodic changing. If it is necessary to drain and refill or add fluid to the transmission, DON'T substitute any other lubricant. Installation of other lubricants may result in internal transmission damage."
GM Fluid Part# 12345871
Towing capacity for 1996 Silverado 2500 2wd 5.7 v8?
I've towed upwards to 10,000 lbs off the hitch for at most 20 miles to the lake or for work....but that's with exhaust, chip, intake, and Detroit locker upgrades. as well as AR off road rims and off road tires...good luck hope this helps
What is the weight of a 1994 Chevy Cheyenne 4x4 truck?
the GVW should be on the door sticker.... try a manual also everyone should have a manual for their vehicle, and a professional shop manual should be available at the library in the reference section for FREE...make copies of the right pages and fix your vehicle like a PRO! :) good luck Dave :)
How do you change the time on the digital clock of your 2003 Golf GTI?
You either press and hold the mode button or there should be an H or M button you can press
What size are the wheel lugs on a 1993 Chevy Cheyenne?
They have 14mm x 1.5 wheel stud, with a bolt pattern of 5 on 5" (2wd, 1/2 ton), 6 on 5.5" (4wd, 1/2 ton & 3/4 ton LD), or 8 on 6.5" (3/4 ton HD & 1 ton)
How do you remove the water pump on a 1998 Oldsmobile Intrigue?
Remove the serpentine belt and the altenator. The water pump is behind the alternator. Make sure to drain the antifreeze.
How much horsepower does a stock 98 Chevy C1500 have?
probably 305hp , the 5.0 L engine is 305, if u have the 5.7 L then you are looking at 350hp that is not correct that is the displacement of each motor not the horsepower!!!
Check to see if you are getting power and ground to the fixture. These fixtures are known to corrode and "open" may have to replace entire fixture Could also be a problem in steering column turn stalk
18436572-#1 is the front plug on the drivers side--bring the #1 piston to TDC on the compression stroke & put #1 plug wire on that position on the distributor cap & continue with the firing order. 18436572 usually the no 1 post on the distributer points towards the no#1 cylinder the cylinders are numbered like this front to back on the drivers side 1 3 5 7 and fron to back on the passenger side 2 4 6 8 that is if you are standing in font of the vehichle facing it do this in a clock wise direction around the distributor.
How much does a 1992 Chevy pickup 4x4 weigh?
I have a 1991 K1500 4X4 it's aprox. curb weight is 5000 lbs.
