0
Chevy G20
Manufactured by the American automaker General Motors Company for the G-Series product line, the Chevy G20 was a passenger van powered by a 4.3 liter V6 engine, which can generate up to 165 horsepower.
1,037 Questions
Where are the mid shaft bearings located on a 1986 Chevy G20 van?
if u mean midshaft bearings on the drive shaft, then that is a bearing in the middle of the drive shaft.it will be near the centre u joint and bolts to the vehicle, with shaft thru the centre of it
Why does the button on the door handle fall in on a 92 Chevy G20 van?
The spring holding the door button in place has fallen out. Remove the door handle and replace.
How do you replace serpentine belt on 91 Chevy G20 van?
This is an easy one. There is a belt tensioner on the How_do_you_change_a_serpentine_belt_on_a_1992_Chevrolet_G20_vanof the engine which applies tension to the serpentine belt. A small wheel rides above the belt and applies the tension. Put a ratchet and socket on the bolt found in the center of the small wheel. The wheel and arm it is attached to will move up as you apply pressure to the ratchet. It is only necessary to move the small wheel and arm a short distance in order to slip the serpentine belt from under it.
The trick will be replacing the belt. If the label showing the routing of the serpentine belt is missing (usually on the air intake pipe) draw a diagram before removing the belt.
Where is the fuel pump reset switch on a 1990 Pontiac van?
GM vehicles do not have a fuel pump inertia switch.
check the silver wire inside the door panel some time they twist the key mechanism ,use your key and a lot of wd40 maybe you need another person to help you
.step 1 ,you have to take of the cover of the door panel.2nd,roll the window up.3rd,locate the long silver steel cable attached to the key mechanism.4th,move it a little bit and at the same time the other person put the key inside and twist to the left and right. that will help you.
Why does the heater blow cold and not hot on 95 Chevy 3500?
check thermostat to be sure enging is getting hot.
Heater control on dash opens doors to direct air flow. check that cables are working behind the dash control. you should hear the doors open and close.
Also there are vacume operated doors. Srart with replace vacuve lines on engine. At the front of vans, as you open the hood there is a round plastic vacume chamber. It is easy for the vacume line the come off there.
There are "vacume engines" that make use of the vacume to open the doors. These can wear out.
Mine has always been vacume lines either broken or disconnected.
While sitting at an idle my 1989 corvettes temp rises to 230 is this normal?
no it is not their is a problem in the cooling system. check the fan belts to see if they're tight check the water pump to see if you can wiggle it or is there water coming from it are any of the hoses bad check by squeezing them is the radiator clogged check by removing both hoses and run water in the top of the radiator where the cap is to see if you get water out the bottom hose. If all this checks out put a pressure test on the cooling system
What is the stock rear-end gear ratio on a 1991 240sx?
The stock rear-end gear ratio for all US 240sx is 4.083
Where is the IAT sensor located at for a 1990 Acura Integra ls?
The sensor is located on the intake manifold or air plenum. It is removed and installed in straightforward fashion; disconnect the wiring connector and remove the mounting screws. Remove the sensor.
How do you change freeze plug on 1994 Chevrolet Silverado?
It depends on the freeze plug. Generally though, pull everything out of the way so that you can get to it. There may be one or more in the BACK of the engine, so to get to those you will need to separate the engine and transmission.
If it's a side freeze plug, for example behind the starter, you would need to pull the starter and anything else that might hinder access to the freeze plug. Then, pull the freeze plug out using whatever method you find acceptable. Generally, if the freeze plug is rusted, you can put a large screwdriver or small pry bar into the weakened area then pry out the freeze plug.
Once the old plug has been removed, clean the opening and install the new one. If you have the type with the tightening screw, just tighten it in to seal it. Otherwise you'll need to press in the new one, making sure to get a good seal.
hi there on mine i have the negative cable running from the batter to the bonnet slam panel and also running down to the main body rail next to the rad and a further cable runs to the lower front part of the engine where the power steering pump bolts on. it might seem a bit excessive but at least i wont have any earthing problems arise form it. hope it helps nate
What fuse protects interior lamps?
horn/dv on my van. I'm having problems with a fuse blowing for my inside lights. horn/dv on my van. I'm having problems with a fuse blowing for my inside lights. horn/dv on my van. I'm having problems with a fuse blowing for my inside lights.
How do you replace the alternator on a 1989 Toyota Hiace van?
1994 Chevrolet G20 won't start unless I step on the gas all the way to the floor?
Sounds like too much fuel in the fuel/air ratio. When you open the throttle all the way, you greatly increase the air flow into the cylinders and when the air flow reaches combustion ratio's the engine will fire off and run. You may want to check the EFI system to see if it is leaking. Try to start it without first stepping on the accelerator pedal at all and see if that helps. If you do not have an EFI system, but a carburetor the accelerator pump valve may be sticking open or leaking. If this is the case you need to replace the carburetor or have it rebuilt.
How many foot pounds of torque for pitman arm to steering gear nut on 1994 g20 Chevy van?
Haynes Manual for 1981 to 1996 Chevy G20 Van says 180 foot lbs of torque.
How do install a new passenger side power window motor in a 1995 Chevy G20 full size van?
not easy pass to a qualified window and door expert
How do you tune up a 350 smallblock?
That depends on the age of the engine.
Air filter, plugs, wires, cap and rotor are always a good place to start.
If it's an older engine you may need to include points and condenser.
If it's TBI you may need to include oxygen sensors and connect it to an engine diagnostic scanner.
You can always look in your owners manual and see what is recommended for the routine maintenance.
You can also do a manuel diagnostic. It will give you a set of codes.
Where is the dimmer switch on Chevy Cavalier 1990?
IT IS LOCATED UNDER THE PLASTIC STEERING COLUMN COVER NEXT TO THE HEADLIGHT SWITCH
Why would a Chevy Astro Van turn but not start?
try the ignition control moduale under distributor cap . Any gasoline engine needs fuel and ignition to start. You can check the coil wire (that's the part that went bad on my astro) and the fuel pump, as well as the ignition module. Listen for the "whirr" of the fuel pump when you first turn the ignition. If you don't hear the pump pressurizing the system that may very well be your problem. Try having someone kick (or rubber mallet) the bottom of the fuel tank while trying to start the motor. This sometimes is enough to get the fuel pump going again when it is going bad.
93 530i BMW car problam is fuel pump to no come power how i fine folte
how to chek relay where is the problam help me
on some vehicles there's an electric jumper i think it's called it's on your distibutor if it goes you don't get any power i don't know if that's it or if all vehicles have one but it's a possibilitie
Where can you find a routing diagram for a Chevy G20 serpentine belt?
Also, a good online resource with schematics is the AutoZone website.
this is a breakdown of the dash http://www.autozone.com/servlet/UiBroker?ForwardPage=/az/cds/en_us/0900823d/80/17/13/9a/0900823d8017139a.jsp
