0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
Where is the crank sensor located on a 1999 Oldsmobile intrigue 35L twin cam V6?
located behind coolant reservoir two bolts. on side of engine held by 1 mounting bolt
Where is the crankshaft sensor on a 2001 sebring 2.7L.?
where is the crankshaft sersor on a 2001 Chrysler sebring located
Where is the crankshaft position sensor on 2001 intrigue?
The crankshaft position sensor is near the front of the motor behind the starter. you need to remove the starter to change it.
Here is a picture for the 3.5L : http://im1.shutterfly.com/media/47a0df00b3127ccef97e38181be400000030O08IZtXLZszag9vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D720/ry%3D480/
What is the problem when your 95 Neon won't start and has no spark at all?
Is it spinning over faster than normal? May be a timing belt. Need more info. B Clear a bad starter may not "spark" or make an attempt to turn engine! if headlights and other electronics work normally, it's safe to say that your battery is in working condition, check your starter yes could be a number of things depending on what the car is actually doing, coil pack? are you with out spark on all cilinders? Check your battery and connections for starters, e-mail me with a little more info and I can let you know how to check to find out exactly what your problem is
Where is the crank sensor on a 1995 Jeep?
The crankcase position sensor(CPS) is on the transmission bell housing on the drivers side. It is high on the drivers side and the bell housing bolts attach it to the transmission
How to Test crank position sensor for Mitsubishi?
The crankshaft position sensor can fail after many years of service. The sensor is on the engine and experiences temperature variations which can eventually cause the wire coil to open. This can happen suddenly or when the parts gets hot. In some cases it may work again after cooling.. To test this failure you need to check the problem code in the computer with a reader. It may show no failure, but if driven when it fails, the code should appear on the reader. It may require running the engine until the engine dies, because if it cools and works again, the code may be cleared.
You have 1994 Chrysler Concorde how can you tell if your cam shaft sensor is bad?
call around to auto part stores if you have a autozone near you they can check them for free
Where is the crankshaft position sensor on a 1997 Chevy Suburban?
Look at the bottom front of the engine / Big pulley. Witch is called a Harmonic balancer. The crank sensor is bolted into the left side of the timing cover behind the balancer.
P.S. After replacing the CPS you may need to do a Case learn (or crankcase learn)..This is a procedure to set the sensor to identify the correct cylinder relative to the crank position. If you cant or dont know how to do this take your car to a professional.
Where is the camshaft sensor on a zafira?
Depends on which engine, but on the 1.8 2002 Zafira its one the front of the block, just above the sump next to the flywheel
Where is the crankshaft position sensor on a 1997 Saturn SW2?
UNDER HOOD, CENTER, REAR ENGINE AREA, BELOW EGR VALVE, MOUNTED IN ENGINE BLOCK You can only get to the crankshaft sensor from the bottom of your car, it's gonna be like a feeling game. It's right behind and above the starter. You're gonna need a 10mm 1/4" drive rachet. You may be able to see it from the top to get a good idea. Green connector with one yellow wire and one purple. I just changed mine today. It's pretty easy, if you jack the car up high enough. Please be sure to block your wheels and use heavy duty jackstands for safety (not cheap aluminum ones). Also remove the negative battery cable first so you don't burn yourself on starter connections. Be sure to where your safety glasses under vehicle.
Where is the crankshaft position sensor located on a 1999 ford contour 2.0 dohc vin3?
sensor is found on front of engine block above the harmonic balance wheel
Where is the crankshaft sensor on a 2000 Chrysler Sebring convertible 2.5 engine?
It is on the top rear of the bell housing.
Chrysler does not use reset switches.
Chrysler does not use reset switches.
The 1998 Saturn SL2 will show a code 340 and 341 for a camshaft position sensor because this part is also considered the crankshaft position sensor on the Saturn. The location of the crankshaft position sensor is behind the alternator on a 1998 Saturn SL2. Both crankshaft and camshaft are the same thing This vehicle is not equipped with a camshaft position sensor. Saturn is the only manufacture that uses a auto pulse generated inside the ignition control module in conjunction with the pulse received from the crankshaft position sensor to determine ignition and injection timing. If you have a code for camshaft position sensor the issue is with the pulse generator in the ignition control module.
How do you replace a camshaft position sensor where is it located?
The Camshaft position sensors (One at the front bank and one at the rear bank, the rear one will require to remove the the fuel injection V-bank cover to access)are located on the cylinder head. The front bank CPS is at the RHS near the Transmission fluid dipstick. Once identified the locations, replacement is easy. Disconnect the harness cover and remove the CPS mounting screws with a ring wrench.
Where is the crank sensor located on 1996 Nissan XE 2.4 pickup?
It is located in the distributer. The part is not sold seporate from the distributer. It is only a dealer item the whole distributer for 450.00$. It is also called the crank angle sensor. Just because the code 0335 comes on on the scan does not mean that the sensor is bad. The best thing to do it take it to a dealer. Actually the one in the distributor is called a camshaft position sensor. You can by rebuilt distributor for around 250.00. The crank shaft position sensor is located on the Transmission housing on the left side.
How do you test camshaft position sensor?
Pin 1 is +5V, pin 2 is Ground and pin 3 is the signal. Use analog voltimeter in pin 2 and 3. Crank the engine: the pointer of the voltimeter shoud oscilate in range 0V to 5V.
Where is the location of crankshaft position sensor on a 2006 Chevy Silverado HD Duramax?
The Duramax don't have a knock sensor.
Camshaft position sensor location 4.6 mercury couger?
The camshaft position sensor is on the front of the engine block. It is on the right front about half way up.
Where is the camshaft position sensor located on a 4 cly 1999 Toyota Camry?
its in the cylinder head, above the power steering pump. when youre looking at the engine with the hood up, look to the left side of the engine. in the back of the head down about 4" there are 2 wires and a plug. this connects to the cam sensor.
Where is the location of the crankshaft position sensor on a 2001 Yukon XL?
Right on the bottom of the engine just after the fan shroud. You can see it, it is visible without removing anything.
Where is the crankshaft sensor on a 1998 Dodge Ram Cummins Diesel?
12 valve it is on the front of the engine, above the crankshaft pulley. 24 valve it is behind the starter, in the side of the block.
Where is the crankshaft sensor on a 2000 passat v6?
the sensor on my 98 is located just above the driver's side axle. i found it easier to remove the tire to work on it. 10mm bolt and the wire travels upwards to the firewall, you may need to clip the ziplocks to remove it.
