0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
Where is the camshaft position sensor located on a 1991 Olds 98?
The cam sensor is located below the water pump and left of center. Most likely if there is a problem with theis, then the magnet has come off of the timing gear (which triggers the sensor). Remove the senor, then use a mirror and turn the motor until you can see if it's still there. Good luck!
Where is the Crankshaft sensor located on a 1995 cadillac concourse with northstar engine?
If your 95 is anything like my 01 Seville the Crankshaft sensor(s) 2 of them are found by going to the front of the car, crawing or sliding under where the radiator is and a little to the passage side by the oil filter there are 2 of them an A and a B senor on the 2001 the service manager told me where they were and I when to the library found a service manaual and xeroxed the page that had a picture of it other wise I would not have known hope this helps cost of my sensors where around 160 each
Where is the crankshaft located on a 1991 Pontiac Grand Am?
Any crankshaft is inside the engine bolted to the bottom of the engine block. Visually from the outside it would be in the center of the engine horizontally, right where the oil pan meets the engine block.
Need location of temperature sensors on 1995 Oldsmobile 98 Regency?
There are two for the engine - they are under the intake plenum attached to the engine. There is one outdoor sensor located in the front of the car - under the facia, and there is one for intake air located in the air - cleaner box.
Where is the camshaft position sensor located on a 1997 Chevrolet Lumina?
on the v6 1997 lumina ,the camshaft sesor is on top of engine right behind the power stiring pump,very small space just follow the four wire plug on top of engine ,plug wires lead right to sensor.i hope this helps you.
Where are the camshaft sensors for a 1996 camaro located?
located in the back of th timing pulley the sensor is attached behind the pulley
AnswerRight in the front near themostat housing there's only one check for voltage before you removeWhere is the crankshaft sensor located on a 1993 Chevy Lumina Z34?
You'll need to pull the passenger front wheel, remove the wheel well cover. This will expose the damper pulley on the crankshaft. Remove damper pulley, remove plastic engine cover. Look inside you will see the sensor. Be sure if you replace it to install the new one exactly the same as the old one was.
Where is a crankshaft position sensor located on a 1997 dodge stratus es V6 2.5L?
the crank sensor goes through the top rear of the bell housing.
Where is Engine Control Computer located on a 1994 Delta 88 LSS?
Clipped to the firewall, passenger compartment, just above where the passenger's feet would be. Remove the plastic cover (I think 7mm bolts) and you'll see the bottom of it.
How do you replace the cam position sensor in a 1997 Ford F-150 pickup with 6 cylinder engine?
We need to know what engine you have to answer this question.
Where is the crank shaft sensor located on a 94 Chevrolet S10 picup truck?
Need to know what size engine.V6, Vortex 4.3
Where do you find the crank position sensor for a 1997 buick lesabre?
its behind the harmonic balancer attached by two bolts but you must first take off the balancer to get to it
Where is thermo sensor located on 95 camaro 3.4 liter?
Go to www.autozone.com and click component location.
Where is crank position sensor on 2001 Dodge Ram 3500 Van 5.9L?
Top of the bell housing, behind the passenger side cylinder head.
Top of the bell housing, behind the passenger side cylinder head.
How do you replace the crankshaft sensor on your 1998 Crown Victoria?
The crank sensor is located on the lower righthand side of the front of the engine. It is behind the crankshaft pulley between it and the AC compressor. It has a plug with two wires and is easily pulled out of the timing cover after removing the one bolt that secures it.
Where is the camshaft position sensor located on a 1997 Chevy truck?
That would be the item that's under the distributor cap and rotor button. It will have an electric wire pluged into it. 2 small torx screws hold it in place.
What is a cam sensor and how do you know when it is going bad and where would you look for it?
The cam sensor tells the computer where your cam is in it's rotation. The info is used to determine spark timing and fuel delivery. if it's bad, you'll run rough or not at all. Vehicles with distributors will sometimes integrate thet sensor with the distributor. Otherwise, it will be located near the cam. I had a Vauxhall Vectra - terrible car!! - one of the problems was engine dying on me at any point whilst driving! it was almost impossible to trace the problem as it was an occasional fault, but stopped for good once the cam sensor was changed.
Can a crank shaft pulley be welded to the engine?
That is a really bad idea, firstly the pulley and crankshaft are two different metals so the weld wont hold anyways ( pulleys are cast ) then there is a very slim chance that it will be perfectly centered when you are done, then theres warpage from the heat, and dont forget that once its welded it wont come off again.. I suggest if you have stripped the bolts that hold it on that you drill and retap the threads to a slightly larger size and use appropriate size and grade bolts, the next step would have to be replacing the crankshaft and remember when putting pulleys on never use a steel hammer.
How do you replace crankshaft position sensor Oldsmobile 1988 ninety-eight?
You have to dismantle the entire engine,,,NO YOU DO NOT ITS JUST YOU HAVE TO DRAIN THE OIL TAKE THE OIL PAN OFF AND GET THAT DANG SENSOR TAKEN OUT THEN REPLACE IT!!
Where is the crank sensor on a 92 Chevy Cavalier 4-cylinder 2.2L?
The crank sensor is located on the back engine wall in the middle, just under the two coil packs (from where the spark plug wires come). There is a wire harness from the crank sensor to the module which holds the two coil pack. The crank sensor is held into the engine by a single bolt. To see all of this, you have to go under the car. I am having an intermittent no start problem with my 93 Cavalier (it cranks, but no spark at all) and I think the crank sensor is my problem.
