0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
Where is the crank sensor on a geo traker 1997 1.6 eng?
It is located right at the back of the valve cover. It sticks out and has a wire plugged right into the top of it. It has one torx head screw in it. It is located right at the back of the valve cover. It sticks out and has a wire plugged right into the top of it. It has one torx head screw in it. the cam sensor is at the back of the head... THE CRANK sensor is in the oilpan behind the dampner (front of the motor) you can get to it fairly easy... it picks up its signal form the halls effect wheel mounted behind the crankshaft timing gear.
Where is a crank sensor located on a 1999 villager?
The crankshaft position sensor is at the rear of the engine where it joins with the transmission bellhousing. It is at the left (front) side, not far from the starter.
Where on the motor is the temp sensor for 1997 s10 2.2?
The engine coolant temp (ECT) sensor on that 97 S10 2.2L would be found close to the thermostat.
Where is the cam position sensor on a 2002 saturn l200?
The 2003 Saturn L200 does not have a camshaft position sensor.
What is a double crank mechanism?
A mechanism of four links in which two cranks are of the same length connected by a connecting rod and the final link is fixed to maintain a constant centre to centre distance between the cranks. example- connection between two wheels of a locomotive.
Where is the camshaft position sensor and the crankshaft sensor located on a 1996 olds bravada?
It is located on the distributor under the cap and rotor
Crank sensor should be on the front bottom of engine by the crank pulley
Where is the crank sensor located on a 1999 Chevy Suburban?
Right above the starter, but you'll have to first drop the starter to get access to the CPSensor. my son in law has a 99 suburban 5.7 and the crank sensor is located on the passenger side of engine at the front by the timing chain cover.
How do you change the camshaft sensor on a Vectra 1.8 16v r reg?
Remove the ignition cable cover from top of engine,then detach the wiring plug from the sensor. Remove the front cambelt cover and you can see the single bolt which holds the sensor in place. Undo this and pull the sensor out upwards.Refit in reverse order,do not overtighten the sensor bolt.(torque 6Nm)
That was a great help. I just completed this procedure myself as an absolute novice but for a 2001 Vectra 2.2 l the procedure is slightly more involved. The cam sensor (Part no 90458252 made by Siemens) can be replaced as above but in order to remove the cambelt cover you need to detach the sub frame that hold up the engine.
Place a jack underneath the engine sump with a block of wood and jack up the engine several turns (Don't lift the entire car!). This will remove the pressure off the sub frame.
The sub frame is bolted with 3 bolts to the engine through the Cambelt cover. Remove these bolts. Take it slowly and adjust the jack if pressure on the bolts is high.
The cambelt cover itself is attached by two bolds as far as I can see and a clip on the top. Remove these. This will allow you to pull back the cambelt cover far enough to access a small bolt that holds the cam sensor in place.
Undo this bolt. Now the cam sensor can be pulled up from the top. Once the cam sensor is removed you can undo the wiring. This is different from the above description because the plug is help in place by a spring clip. Also make sure to attach the plug and locking clip before you insert the cam sensor.
What does the Crank shaft sensor on the Buick LeSabre look like 1995?
Check Autozone.com or another such sight They might have a picture. They did for the same part for my 91 lesabre. (Which may very well be the exact same part)
How do you replace the cam position sensor on a 1997 Buick LeSabre?
there is a 3 wire sensor bolted to the front cover of the engine. use a 10mm socket and remove the bolt. after unpluging the sensor carfully rotate the sensor up and down in order to loosen it from the engine. then pull out
Where is the crankshaft sensor located on a 2003 Altima?
can some one show me where the crank sensor is on a 03 nisson altima a picture would be great
What happens when a oxygen sensor goes bad?
When an oxygen sensor goes bad a car will burn gas at a higher than normal rate because it will not be producing as much power as before. The oxygen sensor checks the amount of exhaust.
How do you change an ignition module on a 3.1 cavalier?
lots of fun....locate the coil pack usually on the front of the motor towards the bottom.take off the coil packs and the module is underneath.under the exhaust manifold.
Gmc 2002 Yukon crankshaft position sensor location?
I have been having problems with finding the crankshaft sensor, what should i do or what can i do?
Where is crankshaft sensor located on 1996 Plymouth breeze?
On a 1996 Plymouth Breeze, the crankshaft sensor can be found above the oil filter. It should be accessible without having to remove any other parts.
How do you align the cams and crank on a 5.4 Triton?
Ford has a SPECIAL TOOL KIT with brackets that mount to the cylinder head. NO OTHER WAY
Where is the fuel sensor for a 1998 Chevy Astro Van located?
if you are refering to the sensor for the fuel gauge, it is in the fuel tank with the fuel pump.
Where is the crankshaft sensor on 99 Intrigue 3.5L?
Someone believes you should, "Take Your coolant tank off and the sensor is located under it. It's fairlly simple to replace once you find it."; You will find a sensor there but not the crankshaft sensor. On a 99 Intrigue with a 3.5L, the crankshaft position sensor is in the engine block just above and behind the starter. get under the car, remove the starter and you should find what you are looking for.
Where is the crankshaft sensor located in a 2001 Chevy Impala LS?
crankshaft sensor is located just behind the crankshaft pulley on the front of the engine(passenger side of vehicle).
On a 4.0 V-6 the crank position sensor is in a fixed location and cannot come in contact with the crank if it is installed correctly.
