0
CV Joints
Commonly used in all wheel drive and front wheel drive vehicles, constant-velocity (CV) joint refers to a universal joint that permits a rotating shaft to transmit power through a variable angle without increasing friction, at constant rotational speed.
889 Questions
Where is the boot on the ball joint?
The boot is the rubber cover The boot is the accorion-folded rubber shroud that fits over the ball joint,
About how much does it cost to replace the cv joint on a 1996 Toyota Avalon?
I just received a quote of $700 to replace both CV axles on mine. That's about $225 each for parts and then labor.
I just received a quote of $700 to replace both CV axles on mine. That's about $225 each for parts and then labor.
I have a certified mechanic who has me buy the parts (saves me a lot of money). He is charging me $200 for labor for the passenger side. I bought the re-manufactured shaft for $63 minus $10 core, so ends up to be $53+tax. So $253 total.
If it only shakes when you are driveing down the road there are a few things to check. Frist check your struts. Make sure all the bolts are there and tight and in good condition. check your brake rotors. If they are warped it will make your car shake when you brake. Make sure the lug nuts on your wheels are all tight. check the balance of your tire. check your ball joints
How do you replace CV axle on 1993 Camry?
First loosen the lug nuts on the side you want to replace the cv axle on. Jack up the car make sure it is secure remove the tire. Remove the spindle nut 32mm socket. Remove the cotter pin and nut from the tie rod end 17mm wrench or socket unhook the tie rod end and move it out of the way. Now that the tie rod is unhooked you can move the hub freely. remove all 6 8mm Allen bolts that secure the cv axle to the tranny. Remove the axle which is easier said than done you have to move it around until it comes out. install in reverse of removal. I don't know the torque specs. I acctually came here looking for them.
To create a CV, you need to list your personal information, academic qualification, professional qualification, hobbies and referee in a systematic order.
What happens with bad CV joints?
Constant Velocity, or CV joints are used in front wheel drive cars to transmit power to the front wheels while allowing them to steer. As they begin to wear out, first you will notice clunking or rattling when shifting between reverse and drive. Later, you may notice vibration or grinding when turning. Eventually, the joint will completely fail, and the car will not move when placed in any gear.
Renault clio oil and filter change?
it's behind the drivers wheel on the back, bottom, right hand side of the engine
How do you take apart a cv joint on a 1990 big bear ATV?
On the cv joint attached to the front differential, if you take off the boot, in front of the bearing, there is a cir clip. If you remove the cir clip the whole cv joint slides out of the differential. Have fun...
How do you replace the axle and cv joints in a 2003 Honda Civic?
This is pretty tricky if you normally don't work on cars. so be advised to not do this if you normally don't work on cars.
First off block off the rear wheels, put the handbrake on.
Jack up the side that you want to work on first.
remove the wheel.
Remove the axle nut, its the giant nut usually 32mm directly in the middle of your brake rotor.
Now, comes the tricky part, remove the cotter pin and nut that is right underneath the hub assembly, it holds the lower ball joint in place. now what i do is take a giant hammer and pound on the lower control arm, its the arm that the lower ball joints piece sticks out. what ever you do don't hit it on the threads where you just took the nut off at.
once you just it a couple of good whacks it should kinda drop and loosen up allowing you to manuver the hub assembly away and take the axle out.
Keep in mind the passenger side may have a intermediate shaft, under the car towards the center that you may need to unbolt also.
How do you remove outer cv joint on front axle on 2001 suzuki 500 quad runner?
it as simple as pulling back the cv boot and hammering the joint off. there is a retaining ring on the inside of the joint. when you put it back together just make sure the ring is in good shape.
How do you replace cv joint 2000 Saturn sl?
generally any more it is cheaper to put a whole half shaft in versus repairing a cv joint.
How do you change cv joints on a 1999 infiniti i30?
jack up entire front end, remove front wheels. break axle nut loose. its on with 180-220 ft lbs torque. remove ball joint from hub OR remove two bolts from strut to hub monting. remove brake line and abs wire from strut [clips] push axle out of hub, and use prybar to pop out of transmission. make sure circlip came out of transmission on axle. push inner joint into transmission, make sure circlip locks into tranny. you should NOT be able to pull axle out with your hands. the PASSENGER side is a PITA. there is a center bearing that creates equal length halfshafts. remove three bolts, and pry axle from carrier, OR unbolt carrier from engine and pry off axle on bench. axle bolts- 180-220 ft lbs. strut bolts - 90-110 ft lbs. ball joints- 40-60 ft lbs.
Are there any special tricks to replacing the passenger side CV shaft on a 2000 Blazer?
Loosen passenger side lug nuts. Raise and safely support front of vehicle with jack stands. Remove wheel. Remove axle hub nut and washer. To release inner CV joint from differential, hit the inner part of the CV tri-pot housing with a hammer and a piece of wood until the snap ring releases. Support lower control arm with a floor jack. Remove brake caliper and hang it out of the way with a piece of wire. Remove brake rotor. Disconnect tie rod end from steering knuckle. Separate and detach lower and upper ball joints from knuckle. Using a puller, push the drive axle out of the hub. Remove steering knuckle. Remove axle assembly. Torque front axle hub nut to 103 ft lbs during assembly.
Once the CV boots have failed (unless you were watching when it happened) the cv joint inside has gone bad from grit and running dry. Don't mess with an individual CV joint. Replacing the whole axle makes much more sense in the long run, since it is actually less effort and you will end up with a new axle and 2 new CV joints. The axle half-shaft includes both CV joints for that side of the vehicle.
How do you fix the gears in the cv joint if it dropped in the transmission?
The transmission will have to be disassembled.
How do you install CV joints in a 1996 Ford Escort 1.8 with standard transmission?
how to change a cv joint on 96 escort
How do you replace cv shafts on 1992 Saab 900?
Before jacking up the car, install Saab spacer tool between the upper control arm and the body. This is important as it preserves a usable angle to remove the axle.
Jack up the car and support it on jack stands.
Remove wheel, remove brake caliper, remove center axle nut, disconnect the tie rod end, remove upper and lower ball joints from A-arms. Remove hub assembly from the car.
Loosen clamp on inner boot. You should now be able to remove the axle.
Outer CV joints can be replaced on the axle. Remove the boot, then remove the circlip holding the CV joint to the axle shaft.
Use a new boot and new grease when replacing the CV joint.
Where can one find a CV builder?
One could find a CV builder on sites such as reed, yourcvbuilder, and mycvbuilder. Some of the sites are completely free while others offer a paid membership.
How do you remove the cv joint from the transmission of a 90 Nissan Sentra?
You have to take it loose from the front bearing then pry it out of the trans. Big Job
How do you remove and replace the cv joint assembly on a 99 Kia Sephia?
Getting a new half axle might be the way to go on this one. It will probably be the next thing to go anyways
