0
Dodge Durango
The Dodge Durango was a full size SUV (sport utility vehicle) manufactured by Chrysler for the Dodge brand. Produced in the company’s assembly plant in Newark, Delaware, this 8-passenger vehicle was initially powered by a 5.9 liter Magnum V8 engine.
3,297 Questions
Where is the throttle position sensor on a 2001 dodge 2500 cummins automatic trans?
It is under the hood, on the driver side front of the engine. It is part of the assembly that the throttle cables hook on to.
How do you get the radiator fan off of a 2001 dodge durango with a 4.7 engine?
36 mm wrench, and a spanner to hold the pulley. Turn to the left.
How do you reset security system without an alarm?
On many vehicles you just need to open the drivers door with the key.
What is the curb weight of the 2005 Dodge Durango?
The curb weight of the 2005 Dodge Durango is 4692 lbs..
Where is the thermostat on a 2003 Dodge Durango 5.9 L?
On a 5.9L the thermostat is under the housing that the upper radiator hose hooks to on the engine.
How do you replace the front wheel bearing on a 2002 Dodge Durango?
to tell u the truth you are better off buying a new boot from a junk yard to put on then messing with the bearings
Where is the location of 2004 dodge durango low side ac port?
The small connector in the a/c line is the low port and the big connector is the high port side ...
How do you remove the rear tire on a 2002 durango?
Inside the tailgate, under the little hatch-door, there is a hole in the carpet. You need to take part of the jack assembly and rotate the stud in that hole until the tire begins to drop to the ground outside. Might need to WD-40 the whole business if it has never been moved.
Where is the map sensor on a 2000 4.7 liter dodge durango?
The MAP sensor is located on the intake side before the intake manifold.
How do you replace the water pump on a 1996 Saturn SC1 sohc?
1. jack the vehicle up on both sides, use jack stands if possible.
2. Remove Passanger front tire, along with plastic splash shield
3. Drain coolant
4. With serpentine belt still installed, loosen the 3 bolts on the water pump pully, don't take them all the way off, just loosen them.
5. Use a 14mm wrench to reduce tention on the serpentine belt enough
so you can slide the belt off
6. Remove the water pump pully bolts, remove pully, or let it rest on the
pump shaft.
7. Remove water pump housing bolts (6 of them) and discard the gasket
8. reverse procedure to reinstall new water pump
Where is the camshaft position sensor located on a Chevy S-10 22L 4-cylinder engine?
On a '99 S-10 2.2, the camshaft position sensor is located on the passenger side of the engine block, about halfway back. You can access it through the wheel well (remove the wheel first, and be sure to use a reliable jack stand). It is directly in front of the coil pack, (about 2 - 3 inches). It has a 3-prong plug. Be very careful when trying to remove it. (I broke the crankshaft sensor off, almost had to pull the engine. I ended up drilling two holes in it and pulling it with a small needle-nosed vice grip.) Don't try to pry it out with a screwdriver. Get ahold of it with vice grips and pull with a twisting motion.
How many oxygen sensors are on a Dodge Intrepid with a 2.7 liter engine?
There are 4. 2 upstraem of the catalytic converts, left and right, and 2 downstream. There are also 2 catalytic converters.
Why would the steering wheel on your car shake?
If it happens when you are driving fast (60-70 MPH) it could be that your wheels are out of alignment.
it is the pastic push button inside of the door jam,when it is pushed IN the light goes off,OUT the light comes ON.
How many horsepower does the engine in the 2013 Dodge Durango have?
The 2013 Dodge Durango's engine produces 290 hp @ 6400 rpm.
Is the 2006 Jeep Wrangler front wheel drive rear wheel drive or four wheel drive?
The 2006 Jeep Wrangler has four wheel drive.
2000 durango heat not working but blowers work?
Either your thermostat has failed (engine stays cold) or your flap that isolates the airflow through your heater core has failed.
How do you change oil in Dodge Durango?
If you have to ask, you probably should take it into 'Jiffy Lube'. But if you want me to hold a course in 'basic automotive maintenance', here you go. WOMEN:
1. Pull up to Jiffy Lube when the mileage reaches 3000 since the last oil change.
2. Drink a cup of coffee.
3. 15 minutes later, write a check and leave with a properly maintained vehicle.
Money Spent:
$20.00 Oil Change
$1.00 Coffee
----------------
$21.00 Total
MEN:
1. Go to auto parts store and write a check for $50 dollars for oil, filter, kitty litter, hand cleaner and scented tree.
2. Discover that the used oil container is full. Instead of taking it back to recycle, dump in hole in back yard.
3. Open a beer and drink it.
4. Jack car up. Spend 30 minutes looking for jack stands.
5. Find jack stands under kid's pedal car.
6. In frustration, open another beer and drink it.
7. Place drain pan under engine.
8. Look for 5/8 box end wrench.
9. Give up and use crescent wrench.
10. Unscrew drain plug.
11. Drop drain plug in pan of hot oil; get hot oil on you in process.
12. Clean up.
13. Have another beer while oil is draining.
14. Look for oil filter wrench.
15. Give up; poke oil filter with screwdriver and twist it off.
16. Beer.
17. Buddy shows up; finish case with him. Finish oil change tomorrow.
18. Next day, drag pan full of old oil out from underneath car.
19. Throw kitty litter on oil spilled during step 18.
20. Beer. No, drank it all yesterday.
21. Walk to 7-11; buy beer.
22. Install new oil filter making sure to apply thin coat of clean oil to gasket first.
23. Dump first quart of fresh oil into engine.
24. Remember drain plug from step 11.
25. Hurry to find drain plug in drain pan.
26. Hurry to replace drain plug before the whole quart of fresh oil drains onto floor.
27. Slip with wrench and bang knuckles on frame.
28. Bang head on floor board in reaction.
29. Begin cussing fit.
30. Throw wrench.
31. Cuss for additional 10 minutes because wrench hit Miss December (1992) in the left breast.
32. Clean up. Apply Band-Aid to knuckle.
33. Beer.
34. Beer.
35. Dump in additional 4 quarts of oil.
36. Beer.
37. Lower car from jack stands
38. Accidentally crush one of the jack stands
39. Move car back to apply more kitty litter to fresh oil spilled during step 23.
40. Test drive car.
41. Get pulled over; arrested for driving under the influence.
42. Car gets impounded.
43. Make bail. Get car from impound yard.
Total Time Spent ???
Money Spent:
$50 parts
$12 beer
$75 replacement set of jack stands; hey the colors have to match!
$1000 Bail
$200 Impound and towing fee
---------------------------
$1337 Total
What is the cost of repairing car air conditioning compressor?
first off you need to determine that i s the cause of your problem,, could be the clutch, hi lo switch, temperature control unit, or broken wire or fuse, if you determine the compressor internally destructed, the entire system refrigerant side is toast, everything along with the compressor needs replaced, plus add a high side filter, new receiver drier, orfice tube evaporator, condenser,and clean out the hoses unless it has a muffler, then they require it be replaced
Where is the fuel filter located for a 1998 Durango?
The Fuel filter is an unaccessable part of the fuel pump assembly, located in the gas tank. The assembly includes the fuel pump, fuel level sending unit, and the fuel filter. Search this WIKI information on replacing the fuel pump.
Where is the fuel filter located on a Dodge Durango?
The fuel filter is part of the fuel pump assembly, located in the fuel tank. It cannot be removed or cleaned. It is also most likely NOT the cause of your problem, whatever it is.
Where is brake light switch located on a dodge durango?
It's at the top of the brake pedal under the dash.
How do you replace the headlight bulb located on a 2002 Dodge Durango?
You first need to remove the turn signal assembly. Do this by removing the torx screw that is in the corner of the groove between the headlight and turn signals. You will also need to unfasten the rubber weather stripping mounted on button-hole style knobs, two on the headlight and two on the signal assembly. Slide the signal unit forward and off to the side. Beware that there are other larger size torx screws that may you see in the vicinity, these are for adjusting the aim of the headlight, so you'll probably want to leave those alone.
With the turn signals removed, you should be able to see the headlight housing bolts. There are 3 bolts; 2 underneath the headlight housing and one on the side of the housing towards the center of the vehicle. Remove these bolts and you can pull out the housing. The housing will still be connected to the vehicle in the outter upper corner with a plastic ball joint type connecteror, just keep pulling or gently pry it off and it should dislodge. Disconnect the wire harness from the rear of the bulb and headlight assembly. Now you can easily unscrew the bulb retaining ring and replace the bulb.
Be sure to use caution when handling the halogen bulb, use a clean rag or paper towel to avoid touching the bulb surface with your hands. Any oil, even body oil from your finger, will heat up and boil on the bulb when it's on and cause the bulb to burn out prematurely. If you get oil on it, clean with rubbing alcohol.
Estimate time for repair: Approx. 15-20 min per bulb.
How do you replace the water pump on a 1990 Dodge Daytona?
Suport engine with a jack under oil pan..remove top right motor mount..remove two bolts that hold POWER STEERING PUMP to the engine bracket..remove bolt that holds BELT TENSIONER to engine bracket..3 or 4 more bolts that hold ENGINE BRACKET to ENGINE..remove ENGINE BRACKET from ENGINE..remove TIMING COVERS..Loosen TIMING BELT TENSIONER...Release SPRING...(Water pump is driven by the timing belt) Remove Timing belt..Remove Water Pump...replace...RE-TIME!..Put back together..be sure to RE-TIME, if you want the car to run again, anyway.. Not an easy job..I hate working on this car.
