0
Ford E-150 Van
The E-150 belongs to Ford’s extensive product line of full-size passenger and cargo vans. Also known as the Traveler, the E-150 features excellent design and a roomy interior for passengers and baggage.
2,051 Questions
What would make your car shake?
Tires out of balance (broke a belt in the tire) or chuck a weight off. Brake hanging up. Front end loose tie rods & balljoints. Lug nuts loose, wheel bearings going or need grease. Pitman arm or steering loose. check all these start at the lug nuts. good luck. (check motor mounts too if it just shakes when it's idling)
How do you replace side mirror on 1999 gmc Yukon?
as far as i can tell you just open your door and there should be a plastic cover, pop it off and undo the nuts and bolts, take old mirror out and put new one in.
Where would the timing marks on a 96 Mazda millenia would be?
Installing the timing belt on a Millenia. I have a Mazda Millenia with a 2.5 liter engine that I just replace the timing belt and tensioner on. In the explanation left and right are in reference to how you are looking at the engine. The timing marks are hard to find. Above the crank sprocket, there is an upside down triangle cast into the block. Behind the crank sprocket, there is a flat disc that rotates with the sprocket. This disc has a notch in it that needs to be lined up with the upside down triangle. Looking at the front of the engine, the camshaft to your right has an arrow on the sprocket. Line this up with the very small tick cast into the block. This should line up the arrow at about a 10:00 o'clock position. On the camshaft located on your left, the original factory tick mark for timing can't be seen without a mirror when the engine is in the vehicle. So, as an afterthought, Mazda came up with another solution. There are two tick marks on the block at about the 12:00 o'clock postion. On the camshaft sprocket are two small drilled out holes that need to line up with these two tick marks. If you haven't already, the hydrolic tensioner needs to be removed, compressed, pinned, and reinstalled. Then remove the idler pulley just below the camshaft sprocket located to your right. Route the belt over the crankshaft, right side idler pulley, right side cam sprocket, tensioner idler, and then left side cam sprocket. While putting tension on the belt, reinstall the missing idler pulley. Then remove the pin from the tensioner releasing tension on the belt. Rotate the crankshaft twice and recheck the timing.
Where is the fuel inertia switch on 2000 ford e-150 cargo van?
In the front passenger footwell , behind the kick panel
How do you change fuel injectors on ford econoline 150?
All questions about cars should include make, year, model, and engine, in order to be able to help you. Without that information, it's impossible to answer many questions.
How much does an 84 ford econoline van weigh?
Approximately 4800 lbs., but this can vary a great deal depending on option and equipment.
How do you wire a utility trailer?
depending on year a lot of newer vans have a 4 flat up under the bumper
Sounds like the heater core is plugged. Have a competent garage flush the radiator and heater core, then refill with fresh coolant. Should cure the problem.
Does a 1985 ford f350 with dual tanks have electric fuel pumps?
yes in the tank each tank has its oen fuel pump
How do you repair the power windows on a 1999 Mazda Protege?
need some more information my friend
The power window motors on a Protege are non-repairable items. Make sure the switches, fuses, and such are in good order before replacing the motor.
What is the firing order for a 2000 ford E-150 4.2L and how hard is it to change a fuel injector?
Replacing the injector itself is not a difficult task. Getting to it is yet another question. You will probably save time and money by taking it to a shop if you do not have the proper tools or experience for removing and replacing fuel rails.
when you put the tank back into place check the angle of the filler hose
Why does fuel pump run for 3 seconds and then stop?
most electrical fuel pumps work that way. it prevents the engine from flooding. also when you run out of gas, you no longer have to crank the engine to get it started again. all you do is turn the ignition to the on and off position 5 or 6 times and the gas reaches the intake. once the engine is running, the fuel pump continues to run and feed fuel to the engine to keep it running. frank t ( a car nut )
When you put the pump in the filler, are you putting it all the way in? If so, try pulling the pump out about halfway and then pump it. It makes a world of difference.
Where is the fuel fiter on a e-150 ford van 1999 5.0 liter engine?
Not tollay sure but when they replaced mine, they came up from the driver side. I doubt it is located there but it is pretty big. About the same diameter as a beer can and about 1/2 as long...
Why the drive shaft vibrates on a ford van E-150?
The drive shaft can vibrate due to damage or if the balancing weights fall off. If the weights are lost, you may take the shaft to a shop that has the equipment and have the shaft balanced again for typically under $50.
Where is the Mass Air Flow Sensor Located on E150 2002?
On a 2002 Ford E-150 :
The Mass Air Flow Sensor is INSIDE a round shaped plastic housing
located between the engine air filter and the engine air intake tube
Where is fuel pump relay on 1994 Ford E-150 Econoline Van?
inside power distribution box under hood on left side by master cylinder
How do you remove the heater fan switch on a 1999 ford econoline?
Need to know how to remove heater fan on 1999 ford e 150 van with small v6 engine
How do you fix 1991 Ford Ranger 4-cylinder heater?
Replace the heater core under the dash board. Fairly easy job if no A/C. But first before you start this, see if is there a coolant leak inside the cab? Usually onto the floor mat and/or what appears to be vapor exiting defrost windshield vent (leaves greasy like film on glass. If above is not happening then check thermostat for proper operation and heater hose connections for leaks. Heater cores are usually no more than $40-50. You should be able to buy at after market auto supply store.
How do you change the water pump on a Ford Econoline e250 Van?
The water pump on a Ford Econoline E250 van is changed by removing the accessories from the front of the engine, draining the coolant, and removing the radiator hoses. The pump can then be unbolted, removed, and a new pump put in its place.
How do you test a fuel pump that has been removed from the tank of a 1990 Isuzu Trooper?
Put some gasoline in a bucket, put the pump in the bucket and use a 12 volt battery to put the pump on. Use a pressure gauge. Put in the output of the hose from where the gasoline will come, and check how many psi the gauge show, I think it has to be 20 or 40 psi.
I would use kerosene for the test fluid; way less explosive!
What would cause the heat in a 1991 Buick Skylark not to get warm?
Thermostat possibly stuck open. Another possibility is the heater core is clogged. I would recommend you perform a complete cooling system service. Drain and flush the system with the heater set to high. Replace the thermostat, and install a 50/50 mix of coolant and distilled water. Bleed all air from the system.
