0
Toyota Corolla
The Corolla is a series of compact/subcompact cars produced by the Japanese automaker Toyota Motor Corporation since 1966. In 2007, the Corolla became the world’s best-selling model, with more than 35 million cars sold.
4,409 Questions
What is the curb weight of the 2008 Toyota Corolla?
The curb weight of the 2008 Toyota Corolla is 2530 lbs..
How many gallons does the gas tank in the 2002 Toyota Corolla hold?
The gas tank on the 2002 Toyota Corolla holds 13.2 gal..
Why would the egi main fuse and egi fuse keep blowing on an '87 Toyota Corolla?
There is a short somewhere.
Are you sure BOTH have failed? Unless the vehicle has been under water, there is very littlepossibility EITHER has failed. These are very heavy duty items and are sealed, so unlessthey have leaked all the lubricant (been hot) or the car has otherwise sustained catastrophic damage,failure is unlikely.Check your tires. Several tire designs cause audible symptoms of bearing failure, in particulartires with hard or aged rubber compounds. Check for scalloped or bevel worn tread...that could be your "noise".
What oil filter to use in a 2005 Toyota corolla?
Use a filter with fiberglass filter element like Wix or Delco, no cheap filter with a cardboard filter meduim, Not only do they do a lesser filtering job they restrict oil flow. If you are asking for a part number, best suggestion is call dealer.
How do you install a starter on a 1997 Toyota Corolla 1.8L?
Remove the positive battery cable from your 1997 Toyota Corolla battery. Tighten the starter with the retaining bolts. Attach the cables to the front of the starter. Reattach the positive cable to the battery.
How do you change rear brake pads on a 1998 Ford Mustang?
The Rear brakes are very easy to change. If you have ever changed the front brakes there is no real differnce.
1) Remove the tire 2) Open the bleader screws located on the caliper 3) Remove the bolts on the caliper holding it in place 4) Remove the caliper. ( note do not lat the caliper hang by the hose use a coat hanger to hang it from the suspension) 5) Remove the worn pads. 6) Depress the caliper piston , it screws down so you will need a $ 5.00 tool to rotate it down, availale at any parts store. 7) Install the new pads and reassamble the caliper. 8) Bleed the air from the brake system. 9) Close bleeder screws 10) Reinstall the tire.
Done
More Information:
I replaced my rear rotors and pads on my 98 v6 mustang today and I wanted to add some information that may help the next novice. Here are some don'ts and do's to make your life easier during this project.
I called several parts places and none of the parts stores that I called had a caliper tool for $5.00 but I did find a caliper tool set at one of the national parts stores that was free but they required me to leave a refundable $60.09 deposit which was ok with me.
I started working on the rear passenger side first. I immediately had trouble with trying to screw in the piston. Yes, first thing I took the brake fluid cap off and then opened the bleeder valve on the caliper but the tool would just slip off the piston when I tried to turn it clockwise. After banging a few fingers I decided I needed to remove the caliper and put it in my shop vice to hold the caliper steady while I put the extra torque needed on the tool to screw in the piston and it worked. I was happy but little did I know that I just made a major mistake.
To put the Caliper in my vice required me to remove the emergency brake spring & cable as well as the brake line. Do not under any circumstance do this unless you are having to replace the caliper. Yes I got the piston screwed in using the vice but it was impossible for me to install the emergency brake spring back around the pin bolt. After wrestling with the emergency brake spring for 2 hours and almost putting my eyes out several times trying to compress the spring, I finally gave up. I figured I needed more tools and experience and in the end this is something I may have a shop do. You can avoid this problem so keep reading.
If your caliper pistons are stuck and are hard to turn with the tool, then here is great way to accomplish your goal. I wished I would have thought about it on right rear.
On the left rear I removed the caliper and caliper bracket, then removed the rotor. With the old rotor removed, I re-installed the bracket and caliper without installing the rotor. I tightened all bolts . What this does for you is... the caliper is bolted down and you can use more torque on the tool to turn the piston in clockwise. The rotor is not in the way and tool will slide through the caliper face to face of the piston.
Once the piston is turned in, the removed the caliper and bracket again then re install with the new rotor & pads.
I had my wife help me bleed the brakes and all seems well except I have an Right Rear emergency spring in the console that needs to re installed if I can figure out how to do it?
How do you fix a P0770 code shift solenoid E malfunction?
How you fix the P0770 code shift solenoid E malfunction error depends on what caused it. The car may be low on transmission fluid or the fluid may be dirty and need to be changed. Other possibilities are a faulty E valve or a bad electrical connection to the E valve.
How do you adjust the outer door handles and locks?
Just a suggestion, but if we knew what the outer doors were attached to it might be easier to zero in on an answer. Are we talking about doors on a house? A car? A 747? Specificity can be a good thing.
Where can you find a vacuum line diagram for a 1986 Olds cutlass?
the diagram you are looking for is on the fan guard connected to your radiator
How do you install a Pioneer CD deck in a 1994 Toyota Corolla?
What is the 2007 Toyota Corolla factory tire size?
Factory 295/65-15 for my 07 CE (5-speed) I think the auto has 185/65-15 stock, My door sticker says 195/65 or 185/65. I have a set of snows running 205/60-15 no rubbing- looks good, but hurts milage. I would recommend 195/60-15 if you don't like the stock cookie cutters.
What is fuel pump fuse labelled as in Toyota corolla?
it isn't a "fuse" as on many vehicles, it would be a "relay switch" or possibly a sensor that could cause a "good" fuel pump not to "turn on"
What makes a 91 Toyota Corolla hesitate while driving?
2 possible obvious faults Ignition timing and\or transmission slip. Hard to say without knowing service history of the engine.
Wiring harness diagram for a 1992 Toyota Corolla?
Im chasing the wiring diagram for 1994 indicator,lights,windscreen wiper arms
How do you replace main seal on 93 Toyota corolla?
replacing the rear main seal is not an easy task. you should have a good amount of auto mechanical knowledge to attempt this. basically you need to remove the transmission from the car. this gives you access to the flywheel. the flywheel has a few bolts on it remove the bolt and your rear main seal is there. note if your car is standard take a good look at the wear on your clutch and flywheel while youh ave the trans down.
How do you reset the Maint required light on a 2005 Corolla after oil change?
I used this on 2004 Sienna and it worked on my 2005 Corolla. With key in off position, press odometer button and hold. Turn key to on position without starting engine and hold button 3 to 4 seconds or until the nag light goes out. Release button and you are good for 5,000 more miles. Thanks to whoever posted the Sienna fix.
How do you replace timing belt 1984 corolla?
First get a Manual
Second read it.
There are to many step in the process of changing The Timing Chain to go into great detail. [http://www.themotorbookstore.com/toycor19.html Go Here for a Manual] Good Luck and Remember.
Change Your Mind, Not Your Oil.
Use the First In Synthetic Motor Oil's.
See My Bio For more information.
When do you replace a 2002 Toyota corolla timing chain?
With a timing belt, it should be changed around 90,000 miles. A chain can last much longer. Have your mechanic check it to see if there is any rattling or loosening on the chain. Some timing chains can last the lifetime of the car.
What does a check engine code PO136 mean for a 1997 Toyota Corolla?
The check engine code PO136 means the O2 sensor circuit malfunction
What is faster a 2009 Toyota corolla or a Honda civic 2008?
hond ia always faster than Toyota no matter how old is it
