Toyota Highlander

Get a manual on your car from the parts store or from AUTOBOOKSONLINE.COM They have pictures too.

Easy Job: Secure: 2 foot piece of clear tubing sized to the bleeder ports (maybe 3./16th inner dia) small glass jar 1 QT correct brake fluid (NEW unopened container) Do not get fluid in eyes , burns like heck (don't ask how I know) If no ABS then remove the brake fluid from the master sylinder with an old turkey baster and replace with fresh, make sure you use the correct flavor fluid. Go to the right rear wheel cylinder: Remove the bleeder dust cover. Use the correct size box wrench on the bleeder affix the tubing put end of tubing into glass have helper pump the pedal 3x then hold. Bleed fluid till pedal hits floor, repeat till fluid runs clean. make sure you replace the cover, it helps prevent rust and siezure of the fitting. Top up master reservoir Drivers rear next and bleed. Top up Passenger front and bleed top up drivers side front and bleed top up. Discard of the fluid properly. If you have ABS get the haynes mmanual for the car and follow the procedure.

Ignition must be ON.

I'm not sure if this is going to help, but the last time I took our Sienna into get its oil changed, the mechanic lifted the hood and yelled out "top-loader" and then ran for cover. A couple of minutes later their double-jointed mechanic came out. I asked him what the deal was.

"Basically the oil filter can only be reached from above and in order to do this the engine has to be either cold or cooled down with water." He said "I always get the top loaders".

I guess its the harsh price to pay for being double-jointed ;-)

Its in a very convienient place. As far as I can tell you have to get to it from the top. You reach under the front exhaust manifold. So better let it cool down first.

actually, its easiest from the bottom.... it is on the front of the engine pointing at the radiator. if you lift the front of the van and look up just past the splash shield you can see it and access it easily with a standard strap type filter wrench.

ANSWER: Oil Filter can be accessed from either top ot bottom ( best from the bottom) it is located approx. center of engine on front side of engine. It's always a good ideal to let engine cool before attempting of remove old filter to avoid get burned. GOOD LUCK!

I have the same problem, have traced it to a relay behind the glove compartment. But I have no idea which relay this is, have noticed if I depress the brake pedal just a bit the clicking stops. I am still looking for an answer.

The 2001 Toyota Highlander has a 4-speed automatic.

Replace the HVAC resistor pack, it is defective.

This happened to me once - - have you checked the air pressure in the spare tire?

2. One under the hood on the drivers side, and one under the tops of your feet on the drivers side.

Yes, it is/was an option.

I believe the tank capacity is approx. 16.5 gal + 2-3 gal. reserve. Hope this helps.

Fuse panel located behind the plastic hatch on the lower left side of the dashboard.

This answer will vary based off of the MODEL of the 2007 Toyota. See sources & related links below. Punch in the exact make, model and year. Note the model number of the rear wiper. Then click on the installation link and watch video for the model of rear wiper. In most cases its super easy. If a rear wiper doesn't display, then you'll have to talk to your dealer since its a special Toyota wiper. That said, most Toyotas use the universal wipers listed for most vehicles on this site.

Auto parts store. The Chiltons and Haynes manuals sold at Autozone, Pep Boys, etc. are of questionable value at best. Spend the extra money (or sometimes less; check eBay) and get the much more complete GM service manual for all "U" Platform vans. You will thank yourself. Sorry I can not find at any part stores a 2002 service manual. try this web site ,,it will cost a little but it is good info http://www.alldatadiy.com/

You can tow any car behind your motor home..

The 2010 Toyota Highlander-Hybrid has 42.4 cu.ft. of cargo capacity with all of its seats in place.

The curb weight of the 2012 Toyota Highlander is 3946 lbs..

This question is too vauge to give a good answer. You need to fill it to the proper level as recommended by manufacterer.

How you fix the P0770 code shift solenoid E malfunction error depends on what caused it. The car may be low on transmission fluid or the fluid may be dirty and need to be changed. Other possibilities are a faulty E valve or a bad electrical connection to the E valve.

The 3rd row seats on 2008 model are optional. Starting with 2011 model the 3rd row seats come standard.

The 2011 Toyota Highlander's engine produces 187 hp @ 5800 rpm.

Factory specs recommend at 90,000 miles.

You would need a "flat rate" manual to determine the alloted time for this operation. To the best of my knowledge they are not available on line. You might try calling your local dealer (or any good mechanical repair shop) and simply ask the service department what amount of time their manual calls for.

The maximum tosing capacity of the 2012 Toyota Highlander is 3500 lbs..

The cabin air filters are located directly behind the glove compartment, undo the small damper on the right side of the glove box and squeeze the sides of the glove box to let it drop down pull the glove box down and then out, it will release from the dash or you can just drop it down far enough to get the cover off for the cabin filter and pull it out.