Toyota Trucks and SUVs

Haydraulic brakes cant be adjust,check your clutch master cylinder for leaks,also look where it comes thru firewall to clutch pedal for leaks,check slave cylinder for leaks,its bolted onto transmission with clutch line connected to it,if any of these parts leak,replace,if no leak is found,then you will need new clutch kit installed.

located up above the break pedal, its an ignorant spot you really have to look up and its fuse number 4, top row its a 15A

there is a short somewhere in dash or heater, you need to fix that to stop fuses blowing

I'm sure it's possible. I've heard of

people putting Turbos from both MR2's as well as Supras. I'm assuming to do so is going to require at least a little knowledge on how an engine works, and even more so how a turbo works. ;) If you're really wanting to Boost your Yota, I would think that an MR2 would be the best bet - Unless you can afford to strip a Supra down. Good luck. Toyota had a turbo for the 22RE . Just haven't looked very very deep into it yet , I have A 94 Toyota pu base model. # 989 off the line , made in Japan . I have had it 12 years this April and I have never had a better vehicle .

Should be a fuse box under the hood with a flasher in the box To get to the flasher relay you have to remove the piece of dashboard under the steering wheel. the flasher will be mounted on a little peg on the left side of the steering column. Hope this helps! -- Brad

Passenger side of inner frame, generally a foot or two back from the door. use the correct size wrenches to disconnect filter, as these are nearly impossible to get off once they are rounded.

On the left upper side of the transmission near the top, maybe a little ways down, you should see a plug, that's the transmission gear lube filler hole.

My son's old Toyota Landcruiser's horn was sticking when he tried to pass state inspection. He pulled real hard on the horn area on the steering wheel and it came off. (after that plastic piece was pulled off, he could see little prongs that held it) Then he saw a loose screw in there that was grounding the horn out. Works fine now. I don't know what he did with the screw. He works out and is strong so he had lot of power behind that pull which was a last ditch try. Lynne in Texas

forgive my ignorance but i believe that the ignition switch is in the dash. first pull off the plastic coving around the switch and put the key in the ignition and roll it to the ACC position and look for a button or sliding lock device that will release the the lock cylinder from the external casing.

p.s. you may need to use a small screwdiver or an ice pick or a pen to push the button in.

Unless you are ready to do some work the ignition on a import is a sealed unit and you will have to drill out 2 or 3 roll pins which are set at 11-2 and 6 approximatly, after removing these pins the cylinder(Thats were the key goes) will then slide out. Then you are able to insert a new cylinder. But if this does seem to be to much of a hastle then your local locksmith is able to do this for you.

They Should be on the metal plate with your engine info, mine are 25R and FL46

It's comes out of the passenger side rocker arm cover. There's a mess of vacuum lines coming off the intake plenum, and it's directly under them. It's nearly impossible to get to it without removing the intake plenum. Reference a Chilton's manual for directions, and make SURE that you label all vacuum and coolant lines accurately.

If it is a 22r four cylinder there are 6. three on the left,two on the right and one on the back. The one on the back is hard to change because the transmission must be dropped.

I have just bought a '95 4Runner V6. It took me several trips to the dealership and the library to figure this one out. The PVC valve is located on the passenger-side valve cover to the the firewall. It is connected to a 3/4 inch hose about 6 inches long with a U-shape at the proximal end. Go buy a new one from O'Reily auto part for $2.50 so you have an idea what to look for. You need a long needle plier to remove this baby. It took me a lttle while to replace the old one.

Code for 2007 hiace

No diff. in any vehicle should go much above 125 degrees Fahrenheit.

Toyota cars- Mitsubishi wheels

Depends on where you live and if any damage was done other than just a blown head gasket. You must fix it so cost is not really a factor unless you want to junk the truck.

is it fuel inj. if so your iac valve is bad(idle air control) MrAmazing added: The 22R-E was manufactured and offered in the states from 1983 - 1995, they were an EFI(Electronically controlled Fuel Injected) motor with a single row timing belt, Check your tension on the timing belt and as this person also said your IAC causing it.

There are four bolts attached to the frame, on either side of the block by your fan belt, it will take some muscle to bust those loose.

Here: http://www.autozone.com/az/cds/en_us/0900823d/80/16/11/88/0900823d80161188/repairInfoPages.htm

it's a little bit hard to figure out. It's the best I can do for you.

The first thing to check would be the condition of the clutch, if it is not releasing completely you will have trouble shifting into first since the engine is moving and the trans is not,all other gears when moving will be easier, next would be fluid level, then syncros.

Can a 22Rcarburater fit a 1979 toyoda pickup .

No, it will only make the exhaust sound deeper. however, note that over time, on some vehicles it will cause premature wear on the engine valves.

The Toyota 1978 20R Emission Control Repair Manual, pub 98268 is still available from Toyota parts, is about $12 and covers all versions of 1978 20R engine emission controls and vacuum lines. You have to have your dealer order it by part number.

One of the best Toyota used truck is the Toyota Hilux. In other countries, the Toyota Hilux is marketed as the Toyota Tacoma.