0
Chevy G20
Manufactured by the American automaker General Motors Company for the G-Series product line, the Chevy G20 was a passenger van powered by a 4.3 liter V6 engine, which can generate up to 165 horsepower.
1,037 Questions
How do you repair the horn on a 1998 Mazda Protege?
The horn is located on the front passenger side of the car. if you remove the front passenger headlight you will be able to see it from there
How much were converse in 1909?
maybe the converse shoes were 20.00 because that is how they cost now actually I just bought a pair two days ago and they were $50!!!!!!
How do you remove the decorative cover on a 2005 Crossfire engine?
Simply pull up on the engine cover it is held in by four clips i believe. The cover with pop off with little strength used to pull it out of the clips . Then slide it towards the windshield to remove the air intake hoses. BK
What would make 92 model 350 Chevy motor die after it warms up?
in my case it was a coolant sensor
but you really need to read the codes
How do you replace Chevy G20 valve cover gasket?
You put your dick on the valve cover and rub mayonnaise on your dick and smear it everywhere to provide a leak-proof seal and that will enable the valve cover to become horny and start kissing your dick goodnight. Thanks and ChaCha!
How do you drain the gas tank on a 1992 Chevy G20 van?
i dont know on that specific van but i can give u my general knowldege if you can get under there and see the gas tank there may be a valve you can open other than that i would take the gas line off and open the gas cap. I just did this as I was changing the fuel pump. There is no drain valve, but simply get under the car, disconnect the fillerneck hose where it enters the gas tank (it's attached with a hose clamp), then use a hose and a pump to drain the tank. It's easier to do it this way as you won't have to fight the kinks and bends in the filler neck when trying to get the hose in.
How do you replace a heater core on a Chevy Lumina?
I replace one of this about 4 month ago. I went from under the dash board make sure you have alot of light you need a metric size 7 mm socket, make sure you have this before you start I kept running to the store.
Remove all the paneling the heater core is closer to the right make sure all the screws are out I missed a few started to pull and broke some plastic of the paneling. I pulled the engine forward to get to the hoses by the firewall make sure that you secure the engine with a 2 x 4 or have someone helping you.
Once everything is loose start maneuvering the core out be careful not to get coolant on your eyes, and by the way completely drain coolant before you start this job. If you don�t chances are you will get an air pocket THIS IS VERY IMPORTANT.
Good Luck and I hope you are as lucky as I was to have a friend spend the whole day helping out.
94 Chevy G 20 van and the headlight go off randomly while driving usually takes 10 minutes or so?
The headlight switch could be the problem
How do you change a freeze plug on a 1999 sebring convertible?
Call your dealer regarding a recall on Sebring freeze plug leaks. You may get the dealer to repair your problem at no cost.
Run a diagnostic code. You probably won't be able to get to any of the transmission codes, but there may be a problem with the VSS or some internal transmission electronic controls.
Where is the neutral safety switch on a 1995 Chevy van?
The 1995 Chevrolet Van neutral safety switch can be located on the top of the transmission. The switch will be just below the shifter.
You have oil all over your block under the hood what happend?
If it's on the back, possible rear main seal leak. Is there oil leaking onto the driveway? Another possiblity is valve cover leak. Its best to check your valve cover closely for leaks and fix them (if present) first prior to replacing the rear main seal.
Replace serpentine belt on a 95 ford van.?
There is a spring loaded pulley that keeps tension on the belt, it should be located near the top left of the engine depending upon which engine you have. The front of this pulley has a torx bit bolt that you'll have to insert a torx bit/star bit socket into and use a breaker bar to back off the tension on the pulley, then you'll be able to remvove the belt. There should be a diagram of the location of this pulley along with the route of the belt on your framework to the left of the hood latch assembly. Hope this helps. My '95 e250 300 6 cylinder has a 3/8 hole in top of pulley assembly. A 3/8 ratchet fits right in and crank to right to remove tension.
Where is the fuel filter located on a 1986 Chevy G20 conversion van?
The fuel filter for a 1986 Chevy G20 should be mounted on the frame under the van. The filter is an inline type and should be easy to change.
Where is the carburetor on a 1989 Chevy van?
from 1987 to 2000 the fuel supply to these wonderful vehicles is a rochester throttle body fuel injection not a carburetor
How do you replace a heater core on a 1990 g20 Chevy conversion van?
This is a very involved process that I could not begin to express here how its done. Check with your local library for a Chilton's repair manual or comparable service manual so you can get very guided details including pictures.
Mcgyver331 added:
This is no fun I am doing this as I am writting today.
First you have to remove the dash. There are various 10mm bolts and Philips head screws.
There are wiring clips on the radio, the headlight switch (there is a button in the rear of the headlight switch to remove the switch rod)and on the gauge panel for easy removal.
Then I would suggest you remove the internal engine cover for easier access. That takes a 1/2in. socket. There are 2 hoses to the left side of the engine bay. You can see those clearly if you remove the air intake rubber duct. The upper hose has the heater control valve on it and the lower one is a return line. These will need a flat head screwdriver or a 10 mm socket to remove the hose clamps.
I am right now trying to remove all the corresponding duct work to free up the heatercore box.
I removed all the duct work, then I found that there are a few bolts that go through the firewall to the a/c box on the engine compartment side. remove the 3 nuts and there is one bolt on the inside right hand side. There is a bracket that holds the dashboard bottom remove that also with 1/2in or 13mm.
Finally the heater box can be removed. you need a 1/4 in socket to split the heater box. there are like 15 little bolts for this. once the box is split you will finally see if the heater core is bad.
I started at this point to split all the duct work in half and clean it with bleach. Once that was done I replaced everything.
work slow if you rush disasters with wiring and vaccum hoses can occur.
thanks for reading
How do you set timing on a 305 motor?
what are the timing marks on a chev 305 motor for the year 1995.
What vehicle transmission is interchangeable with Chevy van G20?
i have a long tail shaft turbo 350 in mine, you have to modify the mount is all, it will fit
Where do you put freon in a 1993 Ford Taurus?
low-side charging port, located on top of the accumulator/drier, on the passenger's side firewall under the hood.
Where is the coolant temperature sensor on a Chevy G20 van?
The G20 has two coolant temp sensors, one temp sensor is at the front on the engine, it has two wires and is next to the thermostat housing, this sensor feeds info the the vehicle ECU. The other sensor is one wire feed and situated on the side of the engine (drivers side) this gives info to the temp gauge on the dashboard.
