Chevy Tracker

Yes in the factory repair manual or possibly online

for a universal cat installed 225.00. maxi automotive greenville , Michigan

It is very hard to do but you will need a 12mm socket for the alternator and a long 12mm wrench to loosen the bolts on the other pully and a 10mm Allen wrench to adjust the A/C belt

http://www.oempartsguys.com/blog/how-to-find-your-replacement-sun-visor/

The belts on the '92 are the same as any other car for the alternator and it is easy. Loosen the main alternator bolt that holds the alt. to the block. DO NOT REMOVE IT! Loosen the small bolt near the top of the alternator, lean the alt. into the block and remove the belt. Put it in a place that you will know which one it is, they are almost the same size! Then remove the power steering belt in the same manner. You will have to loosen the bolts from the bottom and utilize the round holes in the pulley for your socket, as well as from the top side for the tensioning bolt. Set THAT belt in another area so you don't mix them up. I don't have AC, so I assume that the belt for it is similar. They can be a bear getting them over the fan, watch your knuckles! Once you are sure of which new belt is which, install each belt in reverse of the way they came off. I tension the belts with a large screwdriver against the block, using it as a lever to make the belt have about 1/2" movement at the middle point in the belt. Tighten the alternator top bolt first, and then the block bolt. The power steering belt is more difficult, but follow the step to remove it in reverse. AC belt, the same as you took it off in reverse.

Open the hatch-back, the tail light assembly which is red, has two Phillips head sheet-metal screws, one on top and one on the bottom. Remove these two screws and then use slight pressure or a flat-head screw-driver to pry the assembly loose. Be careful not to crack the assembly. The tail-light assembly will have three different caps that have wires leading to them. The one in the middle is the brake light, slightly turn the assembly to the left or right and it should dis-engage, push the bulb down and turn, the bulb should come out. Replace the bulb and use the same procedure in reverse to re-assemble the fixture.

with tools.

How do you change the front rotors on a 2004 Chevy tracker

The dealer can order one for you. EBAY

Hi, It could be a dry or worn bearing on a belt pulley, a dry valve lifter, or a leaky gasket. Pray that it is a leket or pulley, as they are eay and relatively cheap to repair. I had a tick when accelerating in my '00 tracker and it turned out to be a leaky egr valve gasket. I just had to take the egr valve off, scrape away the old gasket with a paint scraper and put a new gasket on. About $25 and a couple of hours later ... no tick. Hope this helps

the factory installs a speaker harness which you can buy from your local audio/video shop and solder the neg- and pos+ on the speaker and just connect them. or you can cut the speaker harness off and solder straight the two neg and pos right on the speaker ans there ya go.. but if you have manual windows you'll have to remove the slip to get in the door and the rear deck just snaps off if you move ur hand along it

The 1990 Geo Tracker IAT sensor is located on the top of the transmission. The IAT sensor will be near the back of the transmission.

2002 ZR2 4-WD/V-6 Locate the large black harness from the Positive batt. terminal and follow it below the exh. manifold on the passengers side. You'll see it leads to the starter housing just below the exhaust manifold.

I just got an estimate for 1200 dollars to replace the one on my 2002.

yes a,90-99,willfit a geo tracker.

2004

walmart $5 a tire

Another Answer That depends on where you purchased the tires. Many places include free lifetime tire balance when you purchase tires from them. Other places will soak you for quite a large fee for mount and balance when you either purchase the tires or have them changed. Caveat Emptor

My 2003 did the same thing and after hours of trouble shooting this and that, my dealers mechanic found a bad crank or cam sensor. Its located behind the motor on the top right side.

The dip stick is on top of the valve cover in the middle,should have a yellow top.

The question you ask is too involved for a proper answer. You may want to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.

The answer to your question is take out the old one and put in a new one. Maybe you meant "Are there any special considerations or problems to consider in the process?"

I own a tracker for 5 years it is a 92. The only thing I had to replace was the computer and got a used one for 300 dollars. It now has 309951 miles on it and still runs great. It only takes 28 dollars to fill up the gas tank. If I was you I would get it and if it used make sure you buy it from a older person.

The 2.0 liter Suzuki engine in the Chevy Tracker uses 5-1/2 quarts of oil to function.

In order to tell you that you would have to describe the noise and what the car is doing when the noise is made. Are you idling, driving, just turned the AC on? What is occurring and what is the noise?

Idling and sounds worse when AC is on.

Sounds like it is coming from the top of the engine. Vehicle has 120k miles

Hi, The first is, is your radiator fluid level ok? second is the very realpossibility that your thermostat is bad. Take a look when you park on a dry spot and see if any fluid is beneath your car. I had a situation once where my water pump was failing and I wasn't getting any heat. If you look for the first two, you will probably will find it. Good luck. Steve H.