Dodge Durango

u have to remove the oil pan , it is in the rear part of the pan and make sure u clean out the oil pan sludge before u reinnstall it and also clean out the pickup tube,

inline fuel under the car in the frame rail up front next the motor area.

It's either the thermostat or the heater controls.

The crankshaft position sensor is on the right side of the engine just to the rear of the right hand exhaust manifold, the sensor is attached to the block with two bolts, part of the sensor overhangs the transmission bell housing. Look at the bell housing and start going up, you will see the sensor almost inline with the right exhaust manifold. It has a gromment that overhangs the transmissions bell housing. Use a flashlight from below and you will see it.

4.25 quarts of oil including oil filter

Work you way from the blower motor first by checking that it has both power and ground and then check the rest of the electrical system............

You open the gas cap and pour gas in the hole, it should be located on the back drivers side behind the little door. Then you screw the cap back on shut the little door and turn the key in the ignition.

it is behind the alternator.

The 2006 Buick LaCrosse has front wheel drive.

190-215 f

16 Plugs, each coil 2 plugs

12 psi minimum at idle.

12 psi minimum at idle.

It is inside the transmission, on the valve body.

The thermostat on a 4.7L is under the housing where the lower radiator hose hooks to the engine.

On the 2001 Durango (with rear AC) the resistor pack is inside the vehicle, on the passenger side. If you are sitting in the passenger seat, your toes are pointing at it. There is a 5 wire harness hanging straight down plugged into it, and it is screwed into the ductwork using 2 8mm screws. It helps to remove the screw holding the duct that restricts access to the front screw holding the resistor and the duct forward as far as possible.

Once the old resistor is out, pull the red lock tab from the connector to remove it.

Install is opposite procedure.

For more information visit: http://www.gtrippleb.com/auto/durango/durango_blower_resister.htm

have the dealership take a look at it, tell you what the problem is! Once you know what the problem is go back to your cheaper mecanic and let him know what it is. Ask for a discount as he himself was unable to diagnose the problem,or considering in some states the dealership will charge a price just to check it out!! The trained tech at a Mitsubishi dealer/repair center will fix it right the first time..

i cant fully answer this question but first you should purchase a repair manual. i know when relacing a water pump you must first disconect the negative connection from the battery, release the pressure and drain the coolant. next you must remove the radiator ,coolant fan and any other things that inhibit the removal of the water pump. remember to purchase the new water pump with a new gasket included. and you will need silicone to seal the water pump when replacing. that's basic hope it helps

In the fuel tank.

It is the same as in any other vechile. If you are not sure of it, you can go to you local police department and they can show you how to put it in. Make sure you do it before you have the baby, most hospitals will check the car seat and make sure it is in correct and if they don't think it is they will keep the baby at the hospital and make you go to the police department to get it put in correctly anyways. congrats on the new baby!

engine US measure metric measure 4.7 liter 17qt 16L 5.2 liter 14.3qt 13.5L 5.9 liter 14.3qt 13.5L

Assuming you're talking about the steering gear box, yes there is. On top of the box toward the front is an adjustment screw. It consists of a metric Allen head plug inside a nut (18 or 21mm, I don't remember exactly). The Allen head plug adjusts preload on the input shaft bearing and the nut around it locks it against the gearbox housing to hold it in place.

To adjust: Have the engine off and the steering wheels straight forward. Loosen the nut on the outside of the Allen head screw, snug the Allen screw GENTLY, then hold the Allen head screw in place and re tighten the nut to lock it down.

Keep in mind that any other component in the steering system can cause excessive play, so if this adjustment doesn't resolve the concern check over all the tie rods, drag link, rag joint, etc. to verify nothing else is worn.

The 2006 Kia Sedona has front wheel drive.

The 2006 Mazda MAZDA3 has front wheel drive.