0
Dodge Durango
The Dodge Durango was a full size SUV (sport utility vehicle) manufactured by Chrysler for the Dodge brand. Produced in the company’s assembly plant in Newark, Delaware, this 8-passenger vehicle was initially powered by a 5.9 liter Magnum V8 engine.
3,297 Questions
Answer no, it has a controller.There is no resistors or relay. There is a blower controller mounted on the firewall, beneath the heater hoses. This was my problem. It cost $46.20 at Mercury or Ford dealers. I'm told that it is a common failure. It's not so easy to replace but you can unplug the cable and plug it into the new one to confirm the failure.
SORRY, BUT THAT'S NOT CORRECT.
There is a Heater Blower Resistor for both, the systems with automatic temp control and without. If you don't have the automatic temp control, good for you, all of the auto parts stores carry them in stock. If you do have auto temp control, or ATC/EATC, they will probably have to order it directly from Ford, which can take anywhere from a couple of days to a week.
If the replacing the resistor doesn't work, you may have to replace the blend door, which is a lot more work.
How do you change the spark plugs on a dodge ram 2003 1500 truck?
I just replaced mine yesterday! Tools you will need: 10mm socket, 10 mm wrench, sparkplug socket, spark plug gap tool, socket extensions (at least 6 inches, preferably 2 3-inch) Step 1: Get the air handling system out of the way. The box that holds the air filter sits off to the right (passenger's side) of the engine bay. It has a large flexible hose that connects to another part of the air handling system (sorry, I don't know the name). This second box connects to the throttle body. You need to move this second box out of the way in order to get to the spark plugs. To do this you will need to remove one 10 mm bolt on each side of the box. Once you get those two out, loosen the hose clamp that holds the box to the throttle body. The hose clamp is on the side of the box closest to the dashboard. When the hose clamp is loose, pull the box up and off of the throttle body. I just left the other hose connected and shoved the box up and toward the passengers side to get it out of the way. Step 2: Now you need to remove the bracket that holds the box that you just removed. Once again, two bolts, one on each end. When the bolts are out, remove the bracket completely and set it aside. Step 3: Now you should be able to get to the sparkplugs without too much trouble. The 2003 4.7 liter engine does not have traditional spark plug wires. Instead it has independent coils, one for each plug. These are also called "coil overs". To remove the coil on each plug you will need to remove a 10mm nut that holds the coil in place on the plug. Remove the nut - try not to drop it - and pull off the coil. The coil may be difficult to remove, but it will come. The nut is all that holds it on. Note that the coil is about 6 inches long and needs a little clearance to get all the way off. The spark plugs are way down in there inside of a heat shield. Step 4: Once you have the coil off it's time for the sparkplug socket. I found it easiest to get the socket onto the plugs without the ratchet handle attached. Add your extension(s) and thread the socket down into the hole that you just took the coil out of. Turn and push until you are sure that the socket is fully engaged on the sparkplug. Then attach the ratchet handle and unscrew the plug. Getting the sparkplug, the socket, and the extension out of that hole can be a bit tricky, but your almost there. Step 5: Check the gap on your new plug, add some anti-sieze compound to the threads to make it easier next time and screw it in. Again, I found it easier to remove the ratchet handle from the extension(s), put the plug in the socket and thread all of that down into the hole. Tighten it hand tight and then snug it up with the ratchet. Step 6: Repeat steps 3 - 5 for each cylinder. Re-attach the bracket and the air handling system and fire it up. Good luck!
Show picture for the wiring of the plugs wire?
show diagram for firing order for a 1996 ford windstar 3.8 engine
Is the 1996 Monte Carlo LS front wheel drive rear wheel drive or all wheel drive?
There are no AWD Monte Carlos.
Where is the heater valve located for Chrysler 300m 1999?
there is no valve hot water flows though core all the time. there is a blend air door and actuator that is almost impossible to get to. center of dash under the console in heater box. you should try to calbrate system just remove the m1 fuse left side of dash under cover. or disconnect battery for10 minutes.
Where do you plug in wiring harness for trailer lights on a 2003 durango?
Buy a kit at Wal-Mart, auto parts or U-Haul comes with instructions
What size wrench do you need to change the brakes on a 2004 Mitsubishi endeavor?
The calipers are held by 17 mm bolts.
Where is the neutral safety switch located on a 2003 Dodge Durango?
It is inside the transmission, on the valve body. It is called a range sensor.
How many quarts of oil does a 2000 dodge durango slt v8 5.2 take?
The 5.2l holds five quarts of 10W30.
What are torque specs for WATER PUMP Mercedes 420 SEL?
Torque specs for WATER PUMP Mercedes 420 SEL are: 7.3 diesel and 15 to 18 foot pounds of torque
Where do you find a motor mount for 1991 Saturn sl1?
If you are talking about the top motor mount on the top passenger side of the motor they are available at many auto parts stores for a whole lot less than a dealer will charge You can view a video on replacing it at youtube under richpin06
I am not sure what causes the climate control to go blank.... however you can manually open the door that allows heat to come in contact with the blower.....remove glove box.... easily done.... (screw inside glove box).... now you have access to heater assembly... there is a white arem visible with a metal link connected to it... pull the metal link off...then grab the white arm and push it over to the right completely...this will open the heater core door. allowing that heat to come in contact with blower...now your blower heat should be hot now! :)
You lost the key to 1998 dodge durango how do you get the key code for a replacement key?
IF the code is not written in the owners manual then you can either go to dealership and have them cut the key for you. Or, you can have a locksmith do it. You can save money by bringing the locksmith the passenger side door cylinder. The reason I'd take passenger side is there's less electronics in the door and usually has less wear. The door and ignition share all the same cuts. The 1997 Dodge Ram also did not have a transponder key that year.
How long does it take to replace a power steering pump in 2000 dodge durango?
It will take approximately 1.5 hours to replace the power steering pump in your 2000 Dodge Durango. The exact amount of time will depend upon the person that is doing the repair.
Why does my 2004 Durango AC Fan stays on one speed?
I had the same problem with mine, the dealership said it's a sensor in the switch.
What size battery does a Dodge Durango use?
The Dodge Durango uses a standard size automotive battery, but there are other options you may want. Some batteries offer more cold-cranking amps while other batteries are designed to work better in extreme heat.
How do you replace the water pump on a 1995 Mitsubishi Eclipse GS 2.0L 16 valve?
left front engine up, take timing belt cover off. Remove timing belt. remove bolts from water pump. but new water pump on. Set timing belt in the same position. But the timing belt and the pullies back on. Then your Finished.
Looking at the repair manual this is a lot harder than it sounds because, u have to remove the motor mount to remove timing belt.
How do you replace an oil pump on a 1998 dodge durango?
u have to remove the oil pan , it is in the rear part of the pan and make sure u clean out the oil pan sludge before u reinnstall it and also clean out the pickup tube,
Where is the fuel filter located on a 1997 Saturn SL2?
inline fuel under the car in the frame rail up front next the motor area.
