0
Dodge Durango
The Dodge Durango was a full size SUV (sport utility vehicle) manufactured by Chrysler for the Dodge brand. Produced in the company’s assembly plant in Newark, Delaware, this 8-passenger vehicle was initially powered by a 5.9 liter Magnum V8 engine.
3,297 Questions
How do you test a power window motor?
Disconnect wires from motor and check to see if you have power and ground going to motor--if so motor is bad if not have to check wiring and switch to that motor
What are the torque specs for a 2001 Kia Sephia water pump?
1. http://kia.com/index.php
2. (lower left side) hover "Kia Owners" >> click "Service Information"
3. Create Login (worth it!!!!!!!)
4. Technical Information
This is a HUGE online repair manual. I was very impressed, overlooking some translation errors.
What is check engine code P1414 for 2006 Dodge Durango?
P1414Secondary Air Injection System Monitor circuit High Voltage
Air pump is shot. Looks like it's time to break out the meter and a wiring diagram! good luck!
What is the wheel base of the 2003 Dodge Durango?
The 2003 Dodge Durango has a 9 ft. 8 in. (116 in.) wheel base.
How many gallons does the gas tank in the 2007 Dodge Durango hold?
The gas tank on the 2007 Dodge Durango holds 27 gal..
Where is the Chevy Trailblazer bank 1 senor 2 location?
Bank one means the driver's side head. If you look at where the exhaust pipe hooks to the manifold and start moving down the exhaust pipe you will come to a 02 senser that will be senser 1. Just keep on moving down the exhaust pipe until you come to the next one and that will be senser 2
Does the top or bottom heater hose from the firewall go to the water pump on a 1991 Dodge Dakota V6?
"Does the top or bottom heater hose from the firewall go to the water pump on a 1991 Dodge Dakota V6?"
The top heater hose from the firewall goes to the water pump and the bottom hose from the firewall goes to the top of the block where the temperature thermostat housing is located.
I'm having the same reason the thing except it doesn't work at all that is clicking I believe its called the relay basically its a square piece connected to some wires easy to take off so I'm going to the junk yard to find one and see if this fixes the problem. if it doesn't fix the problemt then it has to be the current is getting to the window motor. the panel is easy to take off only two screws are underneath plastic caps which took a second to fine the rest of the screws you can spot them easily.
Where is the camshaft position sensor located on a 95 Monte Carlo Z34?
It depends on which engine is in the car but on the 3.1L v6 the cam sensor is located in the top of the block directly behind the power steering pump. The top alternator support bar needs to be removed and then the 3 bolt holding the pump need to be removed (through the pully wheel). Then the pump is pulled straight up without removing the fluid lines. The sensor is held in place with 1 bolt.
What type of oil do i need for 1991 BMW 318i?
10W30 oil is fine for that car. I also have a 1991 BMW 318i and my mechanic who worked for BMW for 20years says to as well.
Is the 2002 Dodge Durango front wheel drive rear wheel drive or four wheel drive?
The 2002 Dodge Durango has rear wheel drive.
How do you replace a catalytic converter on your 1999 Dodge Durango?
best if you take it to a shop unless you have a welder.
What side is the drive wheel on for 91 buick 3.8?
the drive wheel thing is a myth. both wheels pull. on a rear wheel drive car of truck many think the right wheel is the drive wheel. not true. the differential causes both wheels to pull evenly. on a rear drive the right wheel will usually spin first due to the tourque of the drive shaft. on a front wheel drive the wheel that spins first will depend on traction conditions
Actually, the cables for the power window run around inside the door on plastic guides and they sometimes break. I had to take mine to the dealer as they cannot be repaired and the power window system is one unit.
I've had three of these go bad on my 2001 Durango. Its never the motor and always the plastic guides or regulator as said above. I have found one dealer that did sell just the regulator without the motor but for most its all or nothing $300. If Dodge does it your looking at $600. They sell the entire regulator/motor assembly at discount auto $97.00 or pep boys $120.00 and the parts fit exactly. If you've never done this its probably best to go buy the part first so you can see what it looks like because you cant see it even with the door panel off. This will also give you an idea where the screws are for the old regulator/motor. Remove the door panel along with the white plastic sound proofing membrane if installed. Then you need to lower window down 3/4 of the way so you can remove the screws that hold the window to the mechanism. Then pull the window up by hand and secure up with block of wood in door or use a rubber door stop between window and door frame to keep in place. DO NOT LET WINDOW FALL. Then remove four screws that hold regulor guide in place, you will also need to remove 3 screws from motor. If the motor is riveted in place you will need to drill these out first ( replace with screws on reassembly that come with new mechanism). Disconnect electrical plug from motor and reach inside door panel and rotate entire assembly towards the back of the vehicle to get it out the tiny hole. It will fit through as assembled. Installation of new unit is basically the opposite except after you have the regulator and motor installed with screws, reconnect the electrical plug so you can lower the window clamp into position (about 3/4 down). Then remove wood or stopper from window and lower by hand into positon of the regulator clamp. Secure with two screws and your done. Takes less than an hour.
AnswerThere are two screws at the bottom of the door and one above the tweeter. One behind the grab handle and one behind the door lock. The whole panel lifts a little and comes out; none of those old fashioned clips that would always break. the power lock panel lifts from the back. Pull the panel towards you and you will see the two levers that need to be released. Unclip the tweeter and your panel is free. Once you remove the two screws holding the window to the regulator (10mm bolts) you can lift it all the way then put a screwdriver through the top right panel hole to secure it. Do not remove all the bolts, there are some that have keyhole holes. leave the bolts in, loosen them and slide the motor and track over. This will help greatly when it is time to replace everything. you can put the bolts in if you took them out. I found that the cable on mine had jumped the track inside the motor and came off the top pulley. The bottom half round can be removed easily and allows the slide to slide completely off the track. My cable had broken the plastic piece and came out of the anchor. Also, the notches in the pulley allow the cable to be rethreaded into its path. three tiny screws hold the cover over the screw where the cable winds. follow the path and figure out which one needs to be wound around the screw and which one gets one wind only. to get the screw/pulley back into its housing I used a thick screwdriver up from the bottom to position, hold, and then lever into place, compressing the springs almost completely. replace everything and test. Voila $200 saved.How do you replace the water pump on a 1997 Mitsubishi Galant?
To replace the water pump you are going to have to go down past the timing belt. if you dont feel comfortable replacing the timing belt then you would be better off leting a pro handle it. the reason i say that is cause if the timing belt is reinstalled incorrectly it could cause major engine damage (bend the valves)
Where is the camshaft position sensor on a 2000 Dodge 360?
It is the sensor in the distributor under the cap and rotor.
It is the sensor in the distributor under the cap and rotor.
How much is the Time and Repair Cost for exhaust manifold leak for a 2005 Dodge Durango?
$800.00+or-
labor?7-9hrs. =560.00 at 70.00hr.
parts/new[dealer] 600.00+
" / used p&p 150.00 a/pair
after/mrkt high end 400.00+or -
" / " street 240.00 +or-
Where is the thermostat on a 2000 Dodge Durango 5.2 liter?
It is under the housing where the upper radiator hose attaches to the engine.
What is the curb weight of the 2013 Dodge Durango?
The curb weight of the 2013 Dodge Durango is 4756 lbs..
