answersLogoWhite

0

🎒

Example Sentences

Questions asking for an example of a sentence with a certain word in it.

57,929 Questions

If you are making an electric generator should you have thin or thick wire?

For a generator, you'll want fairly thick wire. However, it's important to match the specific materials to the desired specifications; you don't want to pay for over-engineered circuits that will cost and weigh more than the circuit will ever need to support.

What is a page six lover?

"im guessing u got that from thnx 4 the memorys he meen in a list that lover is on page six"

Actually, those that are classified as "elite" are often written about on page six of the New York Post... which is the gossip column. The song suggests that she has a lot of well-to-do/wealthy/socialite lovers.

What does code 37 refer to on a 1994 Plymouth Acclaim?

The 1980s-1990s Chrysler Computer Codes

Start with the ignition off. Within five seconds, switch the key on, off, on, off, on. (On is *not* start!)

The "check engine" light will flash. Count the flashes Each code is a two digit code, so a (for example) 23 would be FLASH FLASH (pause) FLASH FLASH FLASH (loong pause)

It will never flash more than 9 times, watch for pauses!

55 is end of codes - it's normal. Before you call your dealer or mechanic, consider that the blink-spacing is not always perfectly uniform, so if you see 23 23, it's probably just a single 55. (Codes are not repeated.)

33 is normal on earlier models if you don't have air conditioning.

The older Vipers will blink out diag codes with four off/on key turns. They removed the capability starting in... I think 2000, at any rate I know my 2001 requires a computer to check the codes."

On some models (such as a 1995 Neon), when the check engine light goes on, you may be able to get the codes simply by putting in the key and moving it to the RUN position; the light will blink out the codes by itself.

Please note that some codes are NOT included below, this is not a complete listing, but it IS very close to complete. It stemps from a list posted on the Mopar Mailing List, but many modifications have been made.

* Activates Power Limited/Check Engine light on some models.

IMPORTANT. Codes may be different for newer vehicles starting in the late 1990s. See the earlier section.

11 No ignition reference signal detected during cranking (bad Hall effect) OR timing belt skipped one or more teeth; OR loss of either camshaft or crankshaft position sensor. Can cause the engine to stop working entirely with no limp-home mode.

12 Battery or computer recently disconnected

13* MAP sensor or vacuum line may not be working

14* MAP sensor voltage below .16V or over 4.96V

15 No speed/distance sensor signal

16* Loss of battery voltage detected with engine running

17 Engine stays cool too long (bad thermostat or coolant sensor?)

17 (1985 turbo only): knock sensor circuit

--------------------------------------------------------------------------------

21 Oxygen sensor signal doesn't change (stays at 4.3-4.5V). Probably bad oxygen sensor

22* Coolant sensor signal out of range - May have been disconnected to set timing

23* Incoming air temperature sensor may be bad

24* Throttle position sensor over 4.96V (SEE NOTE #3)

25 Automatic Idle Speed (AIS) motor driver circuit shorted or target idle not reached, vacuum leak found

26 Peak injector circuit voltage has not been reached (need to check computer signals, voltage reg, injectors) (SEE NOTE #4 BELOW)

27 Injector circuit isn't switching when it's told to (TBI)

OR (MPI) injector circuit #1 not switching right

OR (turbo) injector circuit #2 not switching right

OR (all 1990-) injector output driver not responding

- check computer, connections

--------------------------------------------------------------------------------

31 Bad evaporator purge solenoid circuit or driver

32 (1984 only) power loss/limited lamp or circuit

32 EGR gases not working (1988) - check vacuum, valve

32 (1990-92, all but Turbo) computer didn't see change in air/'fuel ratio when EGR activated - check valve, vacuum lines, and EGR electrical

33 Air conditioning clutch relay circuit open or shorted (may be in the wide-open-throttle cutoff circuit)

34 (1984-86) EGR solenoid circuit shorted or open

34 (1987-1991) speed control shorted or open

35 Cooling fan relay circuit open or shorted

35 (trucks) idle switch motor fault - check connections

36 (turbo) Wastegate control circuit open or shorted

36 (3.9/5.2 RWD) solenoid coil circuit (air switching)

36 (Turbo IV) #3 Vent Solenoid open/short

37 Shift indicator light failure, 5-speed

OR

part throttle lock/unlock solenoid driver circuit (87-89)

OR

solenoid coil circuit (85-89 Turbo I-IV)

OR

Trans temperature sensor voltage low (1995 and on; see NOTE 2)

--------------------------------------------------------------------------------

41* Alternator field control circuit open or shorted

42 Automatic shutdown relay circuit open or shorted

42 Fuel pump relay control circuit

42 Fuel level unit - no change over miles

OR

42 Z1 voltage missing when autoshutdown circuit energized (SEE NOTE #6)

43 Peak primary coil current not achieved with max dwell time

OR

43 Cylinder misfire

OR

43 Problem in power module to logic module interface

44 No FJ2 voltage present at logic board

OR

44 Logic module self-diagnostics indicate problem

OR

44 Battery temperature out of range (see Note #1!)

45 Turbo boost limit exceeded (engine was shut down by logic module)

46* Battery voltage too high during charging or charging system voltage too low

47 Battery voltage too low and alternator output too low

--------------------------------------------------------------------------------

51 Oxygen sensor stuck at lean position (Bob Lincoln wrote: may be tripped by a bad MAP sensor system causing a rich condition, and the O2 sensor trying to compensate. The O2 sensor may still be good. The MAP assembly consists of two pieces, the valve and the vacuum transducer (round plastic unit with cylinder on top and both electrical and vacuum connections) - If you get hot rough idle and stalling, especially on deceleration, accompanied by flooded engine and difficulty restarting, that can be a bad MAP sensor causing the O2 sensor to try to compensate. If you get poor cold driveability, stumbling and bucking, and acceptable warm driving with poor gas mileage (a drop of 10 mpg or more), that is usually the O2 sensor. [Webmaster note: MAP sensors seem to die regularly.]

OR

51 Internal logic module fault ('84 turbo only).

52 Oxygen sensor stuck at rich position (SEE NOTE #5!)

OR

52 Internal logic module fault ('84 turbo only)

53 Logic module internal problem

54 No sync pickup signal during engine rotation (turbo only)

OR

54 Internal logic module fault ('84 turbo only) - or camshaft sensor/distributor timing (7)

55 End of codes

--------------------------------------------------------------------------------

61 "Baro" sensor open or shorted

62 EMR mileage cannot be stored in EEPROM

62 PCM failure SRI mile not stored

63 Controller cannot write to EEPROM

64 Catalytic converter efficiency failure

65 Power steering switch failure

--------------------------------------------------------------------------------

88 Start of test (not usually given, don't expect it)

Footnotes

NOTE #1.The power module has an air-cooled resistor which senses incoming air temperature. The logic modules uses this information to control the field current in the alternator. This code applies ONLY to alternators whose voltage is computer regulated. If you lose the feed to keep RAM information stored when the engine's off, you also lose battery voltage sensing.

NOTE #2.From the 1995 TRUCK manuals: the trailer towing package includes a transmission coolant temp sensor while the standard package doesn't. This may cause the low (no) voltage indication. -

NOTE #3.The throttle position circuit tells the computer how far the accelerator is depressed. The Throttle Position Sensor (TPS) is on the throttle body on the opposite side of the throttle cable. The connector should have a round rubber cover over the connections. Clear the fault codes, start the car and try jiggling the wires/connectors to try to trip a fault code. Loss of this signal could cause other problems.

NOTE #4.During cranking, the computer will test the current through the injector to see whether there's too much resistance in the injector's path. If there is, code 26 is set.

The problem may be cured with tuner cleaner on the connectors.

For TBI engines, the injector's cold resistance should be between 0.9 and 1.2 ohms (specs vary with year). This is a peak-and-hold injector. With the engine idling the peak period should be about 1.2 milliseconds whereas the hold period will vary. If it's lower than this at idle, then the injector's shorted or there's a defect in the injector driver circuit.

NOTE #5. In my case, the breather tube leading into the catalytic converter had rusted and become detached. This some how would cause the sensor to read an over rich condition and run crummy. I did not trust the reliability of the weld over a corroded surface and opted for the more expensive route of replacing the converter, breather tube and all.

NOTE #6.The Z1 voltage is the voltage of the circuits fed by the autoshutdown relay. This typically includes fuel pump and switched-battery feed to the ignition coil(s). In my Le Baron, the Z1 circuit leaves the power module and splits into two paths: the fuel pump and the positive side of the ignition coil. Internal to the power module is the auto shutdown relay (in my case, it's a sealed box about 1" by 1"). The output voltage is monitored to determine whether the relay responds correctly. I suspect that the ASD relay (and, therefore, the Z1 circuit) also feeds the fuel injector(s) driver(s) and current sensing circuit, but can't prove this.

I've used the Z1 voltage to test for good power connections to the power module. I connected my OTC 500 multimeter from the battery's positive post to the ignition coil's switched battery terminal and measured the voltage drop using the bar graph to monitor peak voltages. Voltage spikes of around 200 mV to 300 mV are ok -- anything more means tv tuner cleaner time (or replacing the power module). Another thing to check is the maximum voltage drop during the priming pulse. With the old power module, I was losing about 2 volts across the circuit; the replacement is losing about 1/4 volt.

Note #7 Inside your distributor you have two pickups, one is for the ignition and one is to tell the computer where number one cylinder is in its rotation. If you look at the four slotted tangs inside there you will see one has a bigger slot, that's the one that tells the sync pickup what's number one. In other words, the pickup inside the distributor is bad.

Is their going to be an xbox 720?

Currently, their has been some leaked documents spreading quite rapidly across the internet, especially among hackers about the release of Xbox 720 in 2013.

Microsoft left a lot of people hungry for details about its next-generation console system at this year's E3. This past weekend, however, those people had plenty to chew on, courtesy of a leaked document that purports to offer plenty of previously unannounced details on the system.

The 56-page document, which first surfaced in the popular NeoGAF forums, presents itself as a road map for the Xbox system through 2015, including alleged details on the so-called Xbox 720, a unique glasses display, and a focus on cloud gaming.

It's critical to note, however, that no sources have corroborated the information in the document, which seems to come from a 2010 internal planning meeting. Still, it packs quite a wallop.

Many of the tech revelations are fairly standard and have been mentioned by developers currently working with early versions of the hardware. 2013 launch? Check. 3D support? It's in there. "Always connected" internet connection? Blu-ray drive? Lofty sales goals? Yes, yes and yes.

The document goes several steps further, however. Running on a Windows 8 foundation, the new box aims to be even more of a living room staple than the current Xbox console, allowing users to record TV content in the background like a DVR. It also details improvements to Microsoft's Kinect camera system: better accuracy, improved voice recognition, and support for motion tracking for up to four players.

That's not all for Kinect. Initially spotted in May by Nukezilla, the alleged roadmap discusses a "glasses for Kinect" initiative called "Project Fortaleza," a pair of Wifi-enabled, augmented reality glasses, according to the document. Marked for a 2014 launch, they would allegedly be radio/4G-based mobile devices that users could take with them, much like Google's Project Glass. Via Xbox Live, the document says, the glasses would offer "real-time information on people, places and objects."

In 2015, claims the document, Microsoft plans to shift focus to cloud gaming -- a move that could signal the next Xbox (or a smaller set top box afterward) as the final hardware product from the group, as the document says consumers will "never need to upgrade hardware again."

Of course, this could all be an elaborate hoax put together by someone with too much time on their hands. Microsoft, while refusing to comment about the document, did have it taken down from the sharing site Scribd via Covington & Burling LLP, a major IP law firm that represents Microsoft. That move, of course, has given the rumors springing from the document more traction.

Microsoft has experienced these sorts of next-gen console leaks before. In the days before the Xbox 360 was announced, details from a market research company study leaked out, showing some of the ideas the company was considering for its next-generation system. Ultimately, the company decided to go in a different direction.

What is still water?

Mineral water without carbonation. The water having no bubbles is still. :)

HTTP what is making something negative sound positive?

This is just a guess, but it sounds like you may be thinking of a euphemism. A euphemism is a "positive spin" on something that usually negative or neutral For example, a "sanitation worker" is another way to say "garbage man." Saying someone is a "permanent guest of the criminal justice system" is a nicer way to say that someone is in prison for life. An argument can be characterized as "a very lively discussion". A used car can be called a "previously owned vehicle." A child whose often disruptive and impulsive in a classroom can be called "a lively, energetic and spirited child".

Why would a 2000 Lincoln LS V8 stall?

Could be fuel related. Bad fuel or clogged filter/Injectors. That would be my guess until I knew more information. i.e. Does it do it all the time or just once.

If you lose your grip on a rapidly spinning merry-go-round and fall off in which direction will you fly and why?

You will fly out in a straight line tangent to the circumference of the merry-go-around at the precise point you lost grip (inertia) and down (gravity) in the same direction of the rotation of the merry go round On the merry-go-round your inertia is trying to send you in a straight line, and the merry-go-round is pulling you inward and deflecting your motion so that you go in a circle. If you are holding on to a pole with your hands, you'll feel the tension as it pulls on you. (In accordance with Newton's third law of motion, you pull back on the pole just as hard as it pulls on you.) The merry-go-round's force makes you accelerate inward and you feel all the mass in your body resisting this acceleration. As the force is conveyed to your body through your muscles, you feel your body resisting the inward acceleration. There's no real outward force on you; it's just your inertia fighting the inward acceleration. When you ride on the outer edge of a merry-go-round, there is only one force on you and that force is inward (toward the center of the ride). That force is called a centripetal force, meaning toward the center. As for your tendency to travel in a straight line, that's just the your inertia. With no forces acting on you, you will obey Newton's first law and travel in a straight line. There is no real force pulling you outward. But you will feel pulled outward. That is called a fictitious force. Fictitious forces always appear in the direction opposite acceleration. In this case you, the outward fictitious force is called "centrifugal force." But remember that it's not a real force; it's just your inertia trying to make you go in a straight line. Finally, when you let go, the resistance (fictitious force) is lost and your inertia carries you out in a straight line from the point where you lost grip and tangent to the circumference of the merry-go-round. Gravity will pull you down to the ground.

Who were the Samaritans?

The Samaritans (In Hebrew: שומרונים‎ Shomeronim) are an ethno-religious group of the Levant with the capital in Damascus, that have discussions to join Israel. They had been formed as people at the time of the Babylonian Exile according 2 Kings chapter 17. when immigrants that came to live in Shomeron (In Hebrew: Shomerim - Keepers of the Law) were eaten by lions and the King sent priests to teach them what the God of the land requires. Religiously, they are the adherents to Samaritanism, an Abrahamic religion or Mosaic branch closely related to Judaism. Based on the Samaritean Torah, Samaritans claim their worship is the true religion of the ancient Israelites prior to the Babylonian Exile, preserved by those who remained in the Land of Israel, as opposed to Judaism, which they assert is a related but altered and amended religion brought back by those returning from exile. There are tensions between Jews and Samaritans since they always had their own Temple and claimed that it was the original sanctuary.

Answer: According to Jewish sources (2 Kings 17:24), after the Assyrians exiled the Israelite Ten Tribes, the Assyrian king brought non-Jews from Cutha, Babylonia and Syria (Hamat), and settled them in the depopulated area where the Ten Tribes had lived (Samaria). They were taught Judaism by one of the Jewish priests (2 Kings 17:27), and they were taught the Torah, which they wrote in the Old Hebrew script.

The Talmud relates how the Samaritans adopted some of the mitzvot (Torah-commands) but not others (Talmud, Berakhot 47b), how they denounced the Jews to Alexander in an unsuccessful attempt to get him to destroy the newly-built Second Temple (Talmud, Yoma 69a), and how they interfered with the declaring of Rosh Hodesh (the New Moon) (Talmud, Rosh Hashanah 22b). Our traditions relate how the Samaritans would waylay the Jews who tried to journey to the Holy Temple.

How do you use producer in a sentence?

A producer is a living thing that can make its own food using photosynthesis.

What is a sentence for the word acrophobia?

The boy's acrophobia prevented him from climbing the ladder.

:p

Many software students now a days show acrophobia to learn thesaurus of words.

Beleivers are always acrophobia to explain rationally how chantings or curses affect. They simply make us believe in existence of God. Rationalists always demand for proof.

Acrophobia is the obstacle for youth who do not study perfectly.

Acrophobia is the lame excuse for failure.

Politicians encourage acrophobia in people so that they do not grow skeptic. Thus they are forced to remain loyal.

Due to acrophobia the Church punished Copernicus and Darwin, the popneers of science.

Acrophobia made our forefathers beleivers. But the rationalists/atheists/skeptics are after proofs; and these people never attribute the modern inventions to God.

What is spiritual assessment?

Taking inventory of your religious beliefs and figuring out where you stand.

What is the meaning of fraternally?

This just means in a brotherly manner. Behaving and supporting brotherhood. Something like freemasons.

How do you put together a skateboard?

You'll need these parts to assemble a skateboard: (1) Deck(board) (2) trucks(axel the wheels attach to) *optinal but reccomended: (2) riser pads(fit between the trucks and deck) (8) 1" bolts w/ nuts to attach the trucks to the deck (4) wheels (8) wheel bearings with (4) bearing spacers (1) sheet of Grip tape ( covers the top of the deak with the no slip sand paper) ~ HELMET AND PADS FOR BEGINNERS !!! ~ - VooDoo 13 -

When shading with a pen you can use what two techniques?

Crosshatching, the formation of lines that intersect, is one technique. How close the lines are determines the darkness or lightness of the shading. Also scribbling can be used in the same manner, although more random, can be used as a different style. And there is pointillism, the formation of dots, used in the same way as described above , can be even more accurate., in the same way photographs are formed.

What is the use of a depression contour?

Hachured lines, which are little ticks pointing downslope on a contour line, symbolize a depression. This shows that the elevation is now decreasing.

How CAN you use the word Harlem Renaissance in a sentence?

African American writers and artists created books, plays, poems, and paintings.This period was known as the Harlem Renaissance.