0
Ford Bronco II XL
The Bronco II XL is a compact sport utility vehicle (SUV) manufactured by the US-based automaker Ford Motor Company. This vehicle is smaller the Ford Bronco and features an optional four-wheel drive (4WD).
321 Questions
How do you remove stock stereo from 1995 ford bronco Eddie Bour?
AS far as i know there is a special too; used to disengage the stero you can order it here www.installer.com/parts/index.html You can make the tool by bending two pieces of wire coat hanger into a "U" shape. To use the tool insert the pieces into the little holes next to your stereo and press outward, you should then be able to slide the stereo out of the dashboard.
How do you take the push rod out of the master cylinder?
Should just pull-out Check for spring clip at end of cylinder
What is tfi module on ford bronco 2 2.9 v6?
Thick film IV ignition system. Attached to the outside of distributor
How do you get 1990 ford bronco II to come out of 4X4?
Will a 2.0L z-tech engine out of a 2000 Focus fit into a 98 Escort?
well...im not completely sure, but im ALMOST sure that it will, i have a 98 zetec escort and my buddy said they have the same engine as the focus...should work
How hard is it to replace a starter in a 1993 Ford Escort?
The 1.9L is the same, except no intake plenum support bracket to remove from underneath. I eventually got this repair done, but it is a tight job that took several hours longer than anticipated and had some issue rewiring the battery cable. But then again, I am a novice. - canavm
How do you remove the gas tank from a 1999 GMC Suburban 4x4?
Remove all of thegas you can as it is heavy. TAke the straps loose and lower it a bit so you can get the hoses and electrical connections undone. Then lower it the rest of the way.
Will the 5.9 engine bolt in or fit into a 1998 Dodge Dakota 4WD?
It will *fit* because they offered that Dakota chassis with a V8. the 5.9 is a heavy engine. It might cause issues with the front end. A diesel Dakota is a cool idea though...
This engine will fit but there are other issues that will arise if you are planning on the swap the pcm for the 5.9 will be required for optimal performance and a tourque converter for a 5.9 is required due to the 5.9 being externally ballanced and the 5.2/3.9 being internally ballanced. depending on the year model of the donor the wiring harness does differ from year to year the injector plugs are different ect. good luck with the swap
How do you remove the gas tank on a 1992 Jaguar XJ6?
i HAVE AN 88 JAG AND THE ONLY WAY I WAS ABLE TO REMOVE THE TANK WAS TO TAKE THE FUEL LINE OFF FROM BOTTOM OF THE VEHICLE BY REMOVING 2 CLIPS FROM THE FUEL HOSES COMING FROM THE TANK AND PULLING THE HOSE A LOOSE
Where can you find fuel line diagrams for an 89 Bronco II?
Your best bet would be to get a chilton or haynes manual for your Bll. They are less than $20 at a part store. They cover just about everything about your vehicle.
How do you remove the fuel line from the top of the gas tank on 1998 Chevy C1500 pickup?
Usually one removes the bed of the truck to work on anything with in the fuel tank. Like replacing the fuel pump.
re: you have to have a tool av. @ any part store fuel line disconect tools they slip in the fuel line on top of the tank you get a whole fuelpump assy. already together when you buy the pump so i have found it is just as easy to cut the white plastic just past the end of the lines on top of the tank then use the disconect tool to take the short pice of the plastic out the way the pump assy. is made not much room then its just a big snapring to get the pump assy. out when going back together grease the big o ring it will make it easer to push the pump assy. back in
1990 bronco 2 how to test fuel injectors to see if they are working?
Buy some STP fuel injector clean and mix it with about 10 gallons of gas and just drive around town , if it doesnt seem to be working at all they may need to be replaced
How do you remove rear interior cargo panels for 90 bronco II?
You can try using a toilet bowl plunger from the outside to pull it out. You will have to remove the the weatherstripping from around the side of the hatch and the left rear door and upper trim around the glass before the lower trim.
Where is the factory amp located on a 1988 Ford Bronco II?
I`m Almost Certain Your Question Is About The Radio. The Amps Right Channel & Left Channel Are Inside The Stereo. If You Are Trying To Increase You Sound Output Opt For An Aftermarket Stereo System. Good Luck Some Ford cars and trucks ( I have a 1996 Bronco Full Size XLT) have a "premium" stereo package that includes an external amp. The head unit does not actually drive the speakers. This amp is often in the rear of the car, try looking in the side panels towards the back. Or contact a Ford dealer and if they are nice they can look it up on microfilm.
How do you replace spark plugs on a 1994 Ford Bronco?
pull the wires, get a spark plug socket and a 4" extension, you will have to play around with using the extension on some and not on others
If a 1989 ford bronco II does not react to the gas paddle what is wrong?
The throttle linkage is likely disconnected at the throttle body. Its under a plastic cover and cant be seen until removed. It clips on and comes off easily
What would cause engine oil to blow back through the fill hole?
It's called "blow-by. It's a condition caused when the piston rings do not seal adequately against the cylinder walls, and exhaust gasses "blow by" the pistons, into the crankcase. Oil vapor and small droplets are constantly movin around inside the engine, and the moving exhaust gas just blows some out of any available opening.
Where is the computer located in bronco 2?
if you are sitting in the driver seat in the car it is right behind you in a little compartment by the floor. just twist it open and there it is
Can a Volvo 740 Turbo engine fit in a Volvo 740 GL chassis?
Yes the engine will fit as well as the oringinal engine since they are block wise the same engine. Wireing how ever is a bit different as well as a few other items are located in different places. Try checking out this link for some very helpfull hints. http://forums.turbobricks.com/showthread.php?t=52466 Good luck with the upgrade. You are going to have 2 holes in the turbo block that the non-turbo didn't have. The oil feed line hole for the turbo and the oil return pipe hole for the turbo! The blocks are DIFFERENT
