0
Ford Bronco II
The Ford Bronco II, a smaller version of Ford Bronco, is a compact SUV produced from 1984 to 1990. The Bronco II offers optional 4WD, mechanically identical to Ford Ranger, but does not have a removable roof.
1,174 Questions
How can you tell if its the solenoid or module when your car stalled and cant get it started again?
if a starter sol. is faulty the car will fail to turn over, all the time or intermitantly. The ignition module will usually cause the vehicle to not start (no spark).
Replace the pick up coil it's inside the distributor. This may fix it.
This line just allows air to flow out of the valves into the intake and leave out the exhaust. I believe it helps to balance the air flow of the intake and the air/fuel mixture.
An object floats when its density is?
It depends on what you want to float it on.
For instance if you want to float a ball in oil the ball's density must be less than the oil's density.
Is a 90 ford bronco 2 4x4 carburatored?
No , the 2.9 liter V6 engine in a 4X4 , 1990 Ford Bronco II is fuel injected
Does an object's ability to float depend on its density?
Yes, it does depend on the object's density; it depends on the liquid's density, too.
An object with a lower density than the liquid it is in will float, while an object with a heavier density than the liquid will sink.
bored over means it has had an overhaul in which the cylinder walls were damaged enough that they had to redrill the holes(bore) bigger. Most of the time you will see motors bored .60 over or less. More than that and the cylinder wall get to thin then they will sleeve it which means they will bore it out and then pressure set a new sleeve in. Also with boring out a good portion of the time people will refit main and rod bearings. you will also hear them say grinding the crank which is the same as boring but instead of a hole they grind the shaft of the crank. if you want more detail let me know i will try to help you out in the best way i can.
Where can you find the fuel pump in a 1984 Toyota Celica gt?
if its fuel injected its in the gas tank
What is the horsepower rating on a 1984 Ford Bronco 2?
In 1986 fuel injection was introduced, and the 2.8 was dropped for the 2.9L E.F.I which was a huge improvement. Your Bronco II spec'd 140 h.p. in 1986. Hope this helped. -- Boost
Would a 0.85g object float sink or remain suspended in tap water?
That depends entirely on the volume of the object
What would cause the Anti-lock and brake light to stay on a 1989 dodge pickup?
Could either be one of three things, A blown fuse, a sensor malfunction, or a computer failure. You need to have the abs checked for codes.
Why wont your electronic 4x4 engage on your 1987 ford bronco II?
where may i get a wiering diagram of 1987 bronco11 4 wheel drive touch and go system
How do you change a heater core in a 1964 corvette?
== == I have a 67' and I tried Bars Leak first in the coolant system. If that does not work look at the firewall for a plate. Go to a bookstore or parts house and buy a Haynes Manual that is specific to your car.
How do you replace the head gaskets on a 1990 Ford Bronco II?
Take the back interior cover off the door (should have 4 screws). Locate the latch and unscrew the 2 nuts with a 5/16 socket and swivel. Reverse order for installation.
Where are the grease points on a 1990 ford bronco?
4 on the front steering linkage, check u joints they might have them. not many on the bronco. I do mine with a single tube of Lube.
How do you tell if something is going to float or sink?
Easiest way, which works under normal conditions, is to compare the object's density with that of water, which is conveniently 1.00. You basically take the mass of the object and divide by its volume. If it's greater than 1, it will sink (in water). If it's less, it should float (in water).
How do you wire a CD player in a 1988 Ford Bronco?
Will probably have to go to an auto sound place and get a wiring adapter for the electricals.
Wood floats in water because it is less dense (lighter) than water.
For the source and more detailed information concerning this issue, click on the related links section below.
How do you change a heater core on a 1998 Ford Econoline V8 air 250?
Drain the engine cooling system. Disconnect the battery ground cable. Disconnect the quick disconnect heater hose couplings at the heater core. This requires a special tool that is available from some auto parts stores. Remove the engine cover. Remove the instrument panel finish panel at the passenger's end of the dash where you would find a glove box if there were one. Remove the heater core cover which is held on with seven screws. Remove the heater core.
Installation
To install, reverse the removal procedure.
Timing diagram for a 1988 ford bronco?
Depending on what you are doing to your motor,if you are overhauling it you would need to set the timing marks on the cam and the crank shaft gears then install the timing chain. If you are just doing maintenance or minor work that requires setting the timing then the following info should be all you need.
On the crank shaft damper or harmonic balancer there will be factory timing marks BTDC (before top dead center) TDC (top dead center)ATDC (after top dead center) Most 5.0L(302) and 5.7l (351w) motors the timing sets between 8-11 degrees BTDC.
Also there are a couple of different ign systems used. Duraspark II-III are the most popular that I have seen. meaning the dist are different. If your truck has duraspark III you have to find a single wire that's capped off somewhere around the dist and un-plug it in order to set your timing. Remove the #1 spark plug and bring the piston to the top of the stroke.
check the rotor to see if it points to the #1 wire pin on the dist cap. if it doesnt then you have to remove and replace your dist to the right position. now you can use a regular timing light to set your timing. that's the way I have been doing it for years and it has always worked for me. hope this helps you out.
Where is the starter located on a 92 ford bronco?
its on the drivers side by the oil tank attached to the tranny like normal.
