0
Ford Bronco
Manufactured from 1966-1996, the Ford Bronco is a two-door sport utility vehicle produced in five generations. Broncos are divided into two categories, which are the early Broncos and the full-size Broncos, and were later replaced by the larger Ford Expedition.
1,597 Questions
try lifting up on the shifter and turning the key it maybe a bad Neutral safety switch
My 1988 bronco ii runs great when cold then dies when it warms up and won't start Any idea?
try the air sensor and fuel filter if not pay 80bucks and get the diagnostics done at ford
Were the Bronco's ever called orange juice?
no they were called OJ's though, for the infamous OJ Simpson police chase in his friends white bronco. they are also said to come with the bloody glove package....
Will a 351w intake fit a 302 with 351 heads?
Yes.
I'm sorry but this answer should be NO, a 351w has a longer stroke than its little brother the 302 making the 351 intake a little wider than the 302 intake.
what's the value of a 1894 Winchester 30 30 with bronco rider on left side rope and spurs on right side with the engraving brave land bold men worth? it's in good condition.
Why do your Ford E-350 Ford Van running lights flash on and off?
You have a faulty headlight switch. It's too much of a load on the headlight switch to run all the lights at the same time. You should run a separate light switch for the running lights.
How much would it cost to get a flywheel replaced on a 89 ford bronco II?
to my knowledge the bronco is an automatic, so you dont have a flywheel. you have a flex plate and ring gear.need to know why you want to replace this
Where is the transmission drain plug on a 1982 ford Full size bronco?
Many of todays vehicles do not have drain plugs. You have to remove the pan to change the filter and fluid.
pre ventricular contractions
when your ventricles fire before your atrium
generally harmless
Positoin of plugs wires on distrubitor on 302?
For a Ford 302 that is not the high outout ( HO ) 5.0 liter version :
The # 1 position on the distributor cap faces to the rear and slightly towards the drivers side
Start with the # 1 position and go COUNTERCLOCKWISE ( the distributor rotor turns COUNTERCLOCKWISE )
1 - 5 - 4 - 2 - 6 - 3 - 7 - 8
-------------------------------------------------------------------------------------------------------------
The engine cylinders / spark plug locations are numbered :
firewall
4 - 8
3 - 7
2 - 6
1 - 5
front
What is wrong if a 97 Bronco has transmission shifting problems?
Ford discontinued the Bronco in '96.
How do you drain and refill transmission oil for a 1990 ford bronco?
auto trans their should be a drain plug on the bottom of the trans and a filler neck with the dipstick under the hood manuel trans again with the drain plug and somethimes its easiest to take out the shifter and fill it from the top also on the auto if their is no plug you may just have to take the pan off
if your going to change the fluid on an auto tranny, you should do a service, drop the pan change the filter. 1st why are you changing fluid, is the transmission acting up?
How do you adjust valves on 1986 ford bronco 2.9?
Valve Adjustment Procedure For
1986 Ford 177 CID (2.9L) V6 Engine
To adjust the hydraulic lifters on this engine, position the cam so the tappet being adjusted is in the base circle area. Loosen the adjusting screw until a distinct lash between the rocker arm tip and the valve tip is evident. Carefully turn the adjustment screw until the rocker tip just touches the valve tip. Turn the
adjusting screw in an additional 1.5 turns.
How do you replaced and adjust your rear pinion bearing on your 1995 ford full size bronco?
chock wheels on vehicle u will need a good heavy duty air gun or a good solid socket with breaker bar now get under vehicle, remove rear U-Joint and lower drive shaft out of the way. next with a snug fitting socket remove the large nut , (pinion nut) that was hidden by the u-joint. then with a hammer knock the pinion yoke off remove bearing. replace with new bearing NOTE: check yoke for wear, you may need to use a speedy sleeve to repair damage. if it looks good you won't.
replace yoke replace washer and pinion nut, (always use a new pinion nut) tighten to specified torque replace drive shaft and U-JOINT, (now is a good time to put new u-joint in while you have it apart) finished
