0
Ford Ranger
Ford Ranger refers to the two distinct lineages of pickup trucks sold by the Ford Motor Company. The first line of Ford Ranger vehicles are sold only in the North America, while the second one are designed and engineered in Japan for the international market.
8,282 Questions
How do you reset the fuel pump shutoff switch on a 2000 ranger?
With your ignition key in the OFF position check for any gas leaks ( smell of gas ) if none , press the reset button down on the switch ( the switch is located in your right front passenger footwell , by the kick panel ) Turn your ignition key to the RUN position for a few seconds , then turn your ignition key OFF again recheck for any gas leaks ( smell of gas ) if none , go ahead and start your Ford Ranger
How do you change the bulb for the license plate on a 2000 Pontiac Gran Prix?
Remove the two screws that hold the cover plate on to the bumper recess and remove the plate. If no cover plate is there, then loosen the screws only. After the plate is removed or the screws loosened what ever you may have on your vehicle just move the housing around the edge of the license plate recess. Turn the bulb assembly 1/4 of a turn counter-clockwise and the bulb housing will come out of the plastic casing. Exchange bulb and reinstall the opposite way.
What size tool do you need to remove the sump plug on a peugeot 306 1.6 xs?
apparently a 21mm socket set. or in the middle some square tool. im just gonna try different size sockets and see if 21mm works
Overdrives's off light mean overdrives is on or off?
If the overdrive's off light is on that means it's off. If it is off then the overdrive is on.
Why 1996 ranger wont start clicks1time?
It could be a loose battery terminal or dead battery! A faulty starter solenoid/relay will often only click once when tryong to start the vehicle.
How do you replace the oil sending unit wgauge on a 1996 Buick LeSabre Limited?
The sending unit is located just above the oil filter. Reach through the passenger side wheel well splash shield, remove it or just position it out of the way, and disconnect the connector. There is a special deep well socket you can purchase or just use a 27mm open end wrench as I did. There is enough room to get the wrench on the flats and turn the sending unit out from underneath the car. Reverse the procedure to install.
Ford Falcon EB 92 running real rough especially while driving at night why?
check/clean the earth lead to the motor. it will be from neg side of battery to the motor. as at night with the light on it might be taken most of you earth to the motor that is worth a try
Where is the EDIS on a 93 Ranger 2.3?
That's the 2 coil packs where one end of the spark plug wires connect ( Electronic Distributorless Ignition System )
How do you change the headlights on a 2000 ford ranger?
I am assumming that you need to change the entire lamp assembly and not just the bulb.
First, remove the metal clips from the plastic nuts where the headlight adjusters are. Second, unscrew the nuts (3 each headlamp)from the adjuster screw. Third, slowly wiggle the headlight assembly forward. Fourth, disconnect the wire assembly from the headlight.
You should take your truck to an inspection station (or garage) to have the final adjustment (aiming) made to the lights. Hope this answered your question,
Steve
Let me greatly expand on Steve's response:
Yes, you have to remove two clips. They are made of low grade steel and when I grabbed the firstone with needle nose pliers it just broke. The top part has a 90 degree flange with a slot. I thought this would be simple but did not realize until looking more carefully that the down side has two catches that engage in the slots in the plastic screw - I'm guessing to prevent slippage. These are not easily disengaged and I ended up using a long narrow screwdrive and hammer to drive them out of position. Then I discovered that the best way to remove th clip as to force it sideways and do a lot of prying until it came off. Be prepared to lose some skin in this - narrow space and sharp edges.
OK that gets the two adjustment clips loose. There is still the third fixed pivot which is on the bottom. You can see it sticking through with a plastic hub and two expanded retaining fingers. This thing is old and brittle. I was able to get on finger off but the other just kept turning away from the screwdriver. I finally manhandled the entire light assembly out, breaking off this third attachment. The hum with the adjusting sreew was still there and I discovered that I could use a Phillips screw driver to remove the screw and then put the screw driver into the hum and drive it out (toward the rear). Once you start to remove the lense you also note that it over laps the rim of the side marker and you will end up partially dislodging that. OK its out. Now you have to get the new one in and getting the three attachments lined up with the holes is not easy as its dark down there. Once they ar in you have to replace the two metal clips. I broke off the catches as there is now way to get the whole thing down in there Pounded them flat, as you have bent them gettiing them out and then worked them back in. Do this on both sides. - hope that you have the alignment close to correct. Never do it again.
What evil enginer came up with this system?
-----------------------------------------------------------------------------------------------------------------
AnswerI did this the other week on the Passenger side you have to take apart the air filter in order to access the bulb and it has got a clip on the top that you must pull up to slide the bulb out of place. On the Drivers side you have to take the battery out only because it is in the way and you will see the connection to the bulb. and same thing you did on the drivers side. to Pull the lap assembly i had to pry off the piece of plastic right where the glue was however I personally am not a very patient person so i took a hammer to the OEM light plastic thing so I could pull the screws out. The other way is to melt the glue w/o melting the plastic.What is the rate for performing chest compressions for an infant victim with one rescuer?
Perform chest compressions for an infant at a rate of at least 100/minute.
Ford 2.9 compression lbs per cylinder?
What is the cylinder compression on a 1991 Ford Ranger with a 2.9?
How do you replace the ignition switch on a 1997 Ford F150 pickup?
First of all disconnect the battery remove steering wheel , there is a round slot in the steering column you insert a rod in there it will release the switch ( be sure to remove negative cable or air bag can go off. You may have to twist the switch back and forth to remove
How to drain the radiator on a 1998 ford ranger pickup?
The drain cock is at the bottom of the radiator above the splash shield. Either you will need to remove the shield or you will need a piece of 3/8" hose about 12 to 14 inches long to attach to the drain tube.
easier way as long as you don't mind a small mess pull the bottom raidator hose off and the fluid will come out very quickly
What is the stock tire size to a 2002 Ranger xlt?
Open the drivers door and on the latch pillar should be an information sticker that
shows the original size tire on the vehicle from the factory
Where is the power distribution box on a 2004 Ford Ranger?
The power distribution box ( which is " live " ) is located in the engine
compartment on the drivers side in a 2004 Ford Ranger
What if the DIN removal tools won't work?
Often its the end of the world!!!!!!!!!!:d
You make sure you have the correct DIN removal tool for that vehicle. If that doesn't work, then you take the vehicle to someone who knows what he is doing.
Where is the obd2 plug situated on a ford ranger 2005 pick up?
On a 2005 Ford Ranger :
The Data Link Connector is below the steering wheel , in the lower part of
the dash , between the inside hood release and the parking / emergency
brake release . It is BEHIND a small removable plastic panel
