0
Isuzu Trooper
The Isuzu Trooper was a midsize SUV manufactured from 1981 to 2005. The Trooper had three generations: 1981-1991, 1992-1997 and 1998-2005. The first generation was basic and underpowered on- and off-road vehicle, while the succeeding generations were more refined and were available in two or four-wheel drive.
952 Questions
Why wont your 87' trooper start When key is in on position it beeps but nothing else when cranked?
Is your clutch pedal depressed? If it is, check switch on clutch pedal.
What are the valve lash settings on a 1989 Isuzu Trooper 4 cylinder gas engine?
The factory sticker on mine says it should be .008 on both intake and exhaust.
Where is the G Sensor on a 1996 Isuzu Trooper?
The g-sensor is located under the passenger side rear of vehicle in front of fuel tank just off of the frame rail. Hope this helps.
Where to locate ecm unit on a 1986 izusu trooper?
Your ECM is located underneath your glovebox.
1. Open glovebox and remove two screws at the rear corners of the compartment. (Should be just above the bottom surface of your glovebox)
2. Remove bottom section of glovebox.
3. Do what you will with the ECM that you have just revealed =]
Have fun!
---Was removing my heater core when I came across the ECM by complete accident.
---1986 Isuzu Trooper II
you would first take a marker and put the sprocket on the ground and where it is bent mark it then put the sprocket on a flat space and heat the part where it is bent take a hammer and hit it soft it should fix it right up
What is the last year Isuzu Troopers were made?
2002 WAS THE LAST YEAR. I HAVE ONE. THE ASCENDER TOOK THE PLACE OF THE TROOPER.
Where is the belt tension release to replace the power steering belt for a 1986 Isuzu trooper?
on the power steering pump bracket on the side closest to the battery look for a 1/2" square hole (incidently use this with a 1/2'" drive socket wrench to leverage belt tension after you put on the new belt when you get there) just below this square hole is the tension bolt for the power steering belt adjustment
What type of pulley is an elevator?
An elevator typically uses a system of pulleys known as a block and tackle. This system consists of multiple pulleys that work together to lift the elevator car by distributing the weight and reducing the amount of force needed to move it. The main pulley is usually attached to a motor, which provides the necessary power to raise and lower the elevator smoothly. This design enhances efficiency and safety in vertical transportation.
How do you remove the Driver Side door panel on a 2000 Trooper?
I found this out when I needed to fix the driver's window on mine. The obvious first step is to remove all screws. Look carefully, there is one or two hidden in the door handle part. Once that is done, get a flat tip screw driver to dislodge the plastic clips and it should pop right off.
I THINK U NEED TO REPLACE THE STARTER
Will parts from a izusu trooper fit on a izusu rodio?
Parts from an Isuzu Trooper may fit on an Isuzu Rodeo, as both vehicles share similar platforms and components, especially in models produced around the same time. However, compatibility can vary based on the specific model year and engine configuration. It's essential to verify part numbers and consult with a mechanic or parts specialist to ensure a proper fit.
Where is the thermostat located on a 1999 Isuzu Trooper?
The thermostat for the 3.5 Liter is under a flange bolted to the top of the block (in the valley), connected to it is a black pipe that connects to the lower radiator hose. This flange has four bolts that are accessed only after removing the intake manifold. Removing the housing that connects to the upper radiator housing optional.
How do you put together the intake manifold on a 1989 Isuzu Trooper 2.6 liter?
Take off the cylinder head and make life easier.
check the ground to the engine block
What is ignition timing on cold eng for Isuzu trooper 2.6L four cyc. engine 1988?
12 degrees Before Top Dead Center (BTDC)
no its a trilogy they made a collectors edition with all three but there isn't a fourth game in the series
Why is your automatic transmission slipping out of all gears for a few seconds?
chances are the clutches are worn out and need to be replaced, so your looking at a transmission overhaul.
a srrewed up axle, tranny, or somethnig is binding.
your front end needs to be lubricated badly. Jiffy lube will do it if your truck is fitted with grease fittings if it doesn't have fittings then you have to replace parts. Word to the wise the front end cost about 900.00 for the parts alone so take it to an experienced mechanic and have him drill in some "zirk" fittings on your front end parts so it can be greased!
How do you change the bulb in a lava lamp?
Remove the lava lamp by lifting up the glass. It separates from the base because it just sits in it. Unscrew the old bulb and screw another one in.
When you remove the bulb you will notice that the bulb and base may not be the size of a standard household bulb. On the inside of the base, or the bottom of the base, there should be information about the type and wattage of the bulb.
You need to get the same type of bulb to insure that the bulb base will screw into the socket. The wrong type bulb may not fit in the socket or the bulb may be too large and the top of the lamp will not fit properly on the base. If you get the wrong wattage, the bulb may not be hot enough or to hit to make the bulb function properly.
How do you remove rotors on a Isuzu amigo?
For the rear, remove the tire and wheel. Remove the Brake Caliper and Brake pad bracket. Then the rotor should slide off the wheel studs. The front may have to have the spindle retaining nut and cotter pin removed once the brake pad bracket is removed. Be careful to not get dirt in the bearing.
How do you change the valve cover gasket on your Isuzu Trooper?
Remove Camshaft fro isuzu trooper 1996
Where is the thermostat located on a 1993 Isuzu Trooper?
Under the water neck, where the upper radiator hose to connected to the intake manifold on top of the engine.
