0
Mazda Trucks
One of the popular trucks produced by Japanese automotive manufacturer Mazda Motor Corporation is the Mazda B-Series. This pickup truck was produced between 1961 and 2006. Other trucks produced by the company include the Wankel-powered pickup truck.
1,485 Questions
Where is the location of the transmission control module on a Mazda B3000?
I don't really know that's why I came on here to find out
Will a 2.8 liter v6 engine work in a 1987 Mazda b2200 truck?
I too am looking for the answer to this question, the 2.2L is too costly to build. And I seem to have bad luck with making a rod know in them.
Where was the 1990 Mazda b2200 truck built?
All the 1986-1993 mazda b series trucks were manufactured in japan.By the way great built trucks for that matter.
Is air needed to change tensioner pulley on 1994 Mazda b3000?
I usually hold my breath when changing the pully, but some folks need air or they'll pass out.
Where is the fuel pump located on a 1998 Mazda B-3000?
Over
Where is the starter motor on your Mazda 3?
The starter is placed center under the Mazda 3 for easy access to the battery connection and the flywheel. You need to remove the plastic shroud under the car to reach it.
How do you fix internal coolant leak on 1990 Mazda b2000 pickup?
If by "internal" you mean inside the cab, the heater core would most likely be the culprit and needs to be replaced. If you mean within the engine, then you have a bigger problem as it could be a blown head gasket, or a cracked cylinder head in which case the cylinder head will have to be removed for repairs.
Why does my 4x4 not work on my Mazda b4000?
Hubs need turning on?
Or maybe a fuse?
If it is an automatic 4wd system (i.e. does not have manual hubs), you may need to replace the hubs.
To diagnose this, jack up the front of the truck and place jack stands under both front axels so that the wheels are just off the ground. Then jack up the back of the truck so that all 4 wheels are suspended off the ground. Start the truck and put it into (forward) gear. the rear tires should be spinning. engage the 4wd system. Look underneath the truck. If the front drive shaft is spinning, but the front wheels are not turning, then you need to replace the hubs. I am told this is a pretty common problem with these trucks.
How do you change the clutch on Mazda B2200?
Quick answer.You have to have alot of tools,a rolling jack and a mazda b series manual haynes or chiltons seriously.There is alot to prepare just to drop the transmission and unhooking the drive line,starter,speedo cable,etc.If your mechanically inclined the haynes/chiltons work great and have all the info.However if something your weary of doing call a couple of shops for a price and make sure if you replace the clutch get the pilot bearing and rear main seal replaced at this time!I suggest replacing the slave cylinder mounted on the transmission at this point as well because these are notorious for failure on the b series trucks and most do not last five yrs or more in general.Hope this helps and trying to elaborate each step is just to tedious but,a clutch job on these trucks are simple.
Need vacuum routing diagram for 87 B2000?
See the attached link below for a color coded diagram that should get you in the ball-park.
Where is the oxygen sensor in a Mazda b2200?
It is located on the exhuast maniflold.Has a single wire and YOU can not miss it.It is very close to the brake master cylinder for reference.Buy the new part so you know what you are looking for.It is really simple.
Where can you find a fuse box diagram on a 1994 Mazda MX3 car?
The lid of the fuse box normally has a diagram on it. If you do not have a diagram you can go to www.mx-3.com and there are online shop manuals that will have such information.
How do you replace the right turn signal assemble in a 2001 Mazda B3000 truck?
For the front there is a tiny bolt above and to the outside of the headlight assembly that screws thru the fender into the turn siignal assembly. For the back the assembly is screwed in by 2 screws on the tailgate side and 2 screws on the outside.
check and make sure the battery is fully charged. check and make sure all battery connections are tight. check and make sure ground wire is tightly connected to the engine block. check and make sure poitive wire is tightly connected to relay/ starter.
Can you see a diagram of how the wires hook to the starter cylinoid on the firewall of a 95 b-2300?
Assuming you are talking about a 1995 Mazda B2300, a red wire from the battery goes to the solenoid on the starter, then a red wire goes from the solenoid to the starter relay which is normally located between the battery and the power distribution box in the engine compartment. A red/light blue wire from the relay connects to the transaxle range (TR) switch (if it's an automatic transm)and a pink wire connects from the TR switch to the starter clutch pedal position jumper/switch (SCPP). From the SCPP, a white/pink or red/light blue wire connects to the starter interrupt relay. From there, the red/light blue wire connects to your ignition switch. Hope this helps. At any rate, I recommend that you purchase a Haynes repair manual for your particular model. I always purchase one for every vehicle I ever buy.
