0
Oldsmobile Aurora
The Oldsmobile was a mid-size 4-door luxury sports sedan produced by General Motors from 1994 to 2003. It was powered by a 4 cam 32 valve 4.0L V-8 engine and featured a 4-speed automatic transmission.
1,019 Questions
How do you remove and replace factory radio in 95-99 Oldsmobile Aurora?
all you have to doo is take off the black trim around the radio. there is like #3 10 mm screws pull them out and switch radios
Where is the thermostat located on a 1995 Oldsmobile Aruora?
Follow the bottom radiator hose to the engine. The termostat is under the neck held on with two bolts. follow the top radiator hose to the engine unbolt that piece connected to engine
Well since I put the question out there, Inow have the answer: It was the blower motor module that needed to be replaced. It was burned out. It cause me 251.00 for part and labor.
What bulb does the rear fog lights on a 2001 Aurora use?
Bulletin No.: 01-08-42-005A
Date: February, 2002
INFORMATION
Subject:
Rear Fog Lamp Longer Life Replacement Bulb
Models:
2001-2002 Oldsmobile Aurora
This bulletin is being revised to update the parts information. Please discard Corporate Bulletin Number 01-08-42-05 (Section 08-Body and Accessories)
This bulletin is being issued to inform dealers of the availability of a longer life replacement bulb from GMSPO for the existing rear fog lamp bulb that may have prematurely burned out.
The new rear fog lamp longer life replacement bulb, P/N 22692679, has a trade or standard bulb identifier number of 921LL.
Refer to Fog Lamp Replacement - Rear in the Lighting Systems sub-section of the Service Manual for the replacement procedures.
Parts Information
Parts are currently available from GMSPO.
ther a 912, or 922 bulb. Both are physically similar but one has a higher wattage. Either one will work. I believe I put 912's in mine.AnswerCorrect. Use either the 912 or 922. Do not use the 921:- 912 - 1 watt - MSCP = 12
- 922 - .98 watt - MSCP = 15
- 921 - 1.4 watts - MSCP = 21
Oil capacity 1989 Ford e-350 with 351 W?
Drain the oil and remove the filter. Install a new filter and add 5 quarts. Start the engine and run for 45 seconds. Shut off and let sit for 45 minutes. Check the level and add until it is full. If it is already full it holds 5 quarts. If you have to add 1 quart it holds 6. My guess would be 5 although some 351 Ford engines do hold 6.
Why does sunroof make grinding noise when opening or closing on 99 Oldsmobile aurora?
A grinding noise when opening or closing the sunroof on a 1999 Oldsmobile Aurora could indicate several issues. Common causes include a lack of lubrication on the sunroof tracks or mechanisms, misalignment of the sunroof glass, or worn-out gears in the sunroof motor. Additionally, debris trapped in the sunroof channel can also cause grinding sounds. Inspecting and addressing these areas can help resolve the issue.
How do you replace oil pan gasket 0n 96 aurora Oldsmobile?
To replace the oil pan gasket on a 1996 Oldsmobile Aurora, start by draining the engine oil and removing the oil pan bolts. Detach the oil pan from the engine block, taking care not to damage the mating surfaces. Clean the surfaces thoroughly, then place the new gasket on the oil pan. Reattach the oil pan, tightening the bolts to the manufacturer's specifications, and refill the engine with oil.
How do you change the starter on a 99 Chrysler Cirrus and where is it located?
To change the starter on a 1999 Chrysler Cirrus, first disconnect the battery to ensure safety. The starter is located on the lower right side of the engine, near the transmission. Remove the bolts securing the starter, disconnect the electrical connections, and then replace it with the new unit. Reassemble by reversing the steps and reconnect the battery.
How do you air up shocks on 2002 aurora?
To air up the shocks on a 2002 Aurora, locate the air suspension fill valve, usually found near the rear of the vehicle. Use an air compressor or a manual pump to connect to the valve and inflate the system to the recommended pressure, typically around 30-35 psi. Monitor the pressure gauge to avoid over-inflation, and ensure the vehicle is on a level surface during the process. After inflating, check for any leaks and ensure the suspension is functioning correctly.
