answersLogoWhite

0

🚗

Brake Fluid and Lubrication

Cars, trucks, motorcycles and even bicycles use hydraulic braking. Brake fluid is used to transfer the force applied into hydraulic pressure. In contrast, lubricants enable parts to move opposite each other in a perpendicular manner.

1,926 Questions

Where do you put brake fluid in a 2003 Ford Taurus?

If you don't know where brake fluid goes please stop by any auto parts store and someone there will be happy to show you. Accidentally mixing fluids could cost you big money and even your life.

How do i top up brake fluid in 1997 ford escort?

You add brake fluid to the mastercylinder that is under the hood on the drivers side on the firewall close to the hood hinge. It will have a top that snaps off and it should have a line in it that will let you know when it's full.

What kind of brake fluid go in to a 2000 dodge neon?

DOT3 or 4. Opened bottles will absorb moisture over time, a good rule of thumb is buy a new bottle, close tight after use, write the date on it, and trash it if it's 1/2 empty or 6 months old.

Where is the brake booster check valve for 2002 Dodge Durango SLT 2WD 4.7Ltr?

It'll be in the vacuum line(or the fitting itself) at the booster or in the hose going to the motor.. See if your local library has a professional shop manual to look at for free... dave

What brake fluid for 96 cougar?

According to the 1996 Mercury Cougar Owner Guide :

( DOT 3 brake fluid , meeting Ford specification ESA-M6C25-A )

Where do you add the brake fluid on a 2001 Honda CR-V?

On the left side of the engine compartment mounted on the firewall you will see a white plastic cylindrical container with a black rubber cap. Remove this cap (being careful not to get dirt inside the fluid compartment) and add fluid to this reservoir.

Where is the brake fluid resovoir located in a 2006 Chrysler Town and Country mini van?

The brake fluid reservoir is under the hood on the driver side. It is the yellow cap back near the base of the windshield.

How can you get brake fluid to rear brakes on your mini?

The brake fluid reservoir will be located toward the back of the engine bay on the driver's side, up high where it's easy to access. Once you locate the brake fluid reservoir, you will see markings on the side that tell you if you need to add any brake fluid. You may need to clean off a little road grime to see the marks clearly.

Brake fluid filled up to cap what effect would this have on the braking system?

None whatsoever. I would recommend you remove enough to get it down to the full mark.

What to do after add break fluid?

If the fluid level had gotten so low that you got air in the lines, you will need to bleed the brake lines. It involves opening a small valve at each caliper and/or drum and pumping the brake pedal until you push out any air and you have nothing but brake fluid left in the lines.

Where is the brake fluid reservoir in 87 vw vanagon?

Pretty sure it is in the dash. If you push forward on the instrument cluster housing it will come off and you will see the reservoir on the left.

Where is brake booster located on a 2000 Volkswagen beetle?

It is located behind the airbox on the left side of the engine compartment. It is setting back behind the brake master cylinder on the firewall.

What would make a 1998 Mitsubishi spyder gt use clutch fluid but it is not leaking out?

You can't have it both ways. If it's using fluid, then it is leaking out. If you are not seeing any on the ground or at the slave cylinder have you considered that it may be leaking from the back of the master cylinder and running inside of the car. You may not have noticed because it is going between the firewall and the carpet.

Where is the brake fluid reservior on a VW T2 campervan?

Look under the seat! It has to be behind the spare tire in front of the car!

Brake fluid flush?

Easy Job: Secure: 2 foot piece of clear tubing sized to the bleeder ports (maybe 3./16th inner dia) small glass jar 1 QT correct brake fluid (NEW unopened container) Do not get fluid in eyes , burns like heck (don't ask how I know) If no ABS then remove the brake fluid from the master sylinder with an old turkey baster and replace with fresh, make sure you use the correct flavor fluid. Go to the right rear wheel cylinder: Remove the bleeder dust cover. Use the correct size box wrench on the bleeder affix the tubing put end of tubing into glass have helper pump the pedal 3x then hold. Bleed fluid till pedal hits floor, repeat till fluid runs clean. make sure you replace the cover, it helps prevent rust and siezure of the fitting. Top up master reservoir Drivers rear next and bleed. Top up Passenger front and bleed top up drivers side front and bleed top up. Discard of the fluid properly. If you have ABS get the haynes mmanual for the car and follow the procedure.