Chevy Tracker

no 2004 colorado

Your problem is most likely being caused by your daytime running lamp sensor. It's located on top of your dashboard near the windshield on the passenger side. Try disconnecting the sensor. A little more info might help narrow the problem, like , do you bright lights work when you push the turn signal lever forward, or do they only work when you pull it back, in it's temporary brights position? If this is the case, you can rest now. Don't let anyone tell you to replace the assembly on the steering column. That's a cool $200.00 bucks for a brand new part that isn't going tofixthe problem. Of course you should check all fuses that are related to high and low beams. Hope this helps you out.

If fuel injected- in the fuel tank

If you mean the serpentine belt that runs the pulleys on the front of the car, there is a tensioner pulley that you can turn with a wrench to release the tension. Make sure you remember the routing of the belt so you can put the new belt on the same way.

check the ground wire to that headlight .

i guess you mean,

no park, swapped ECU ? and still no spark.

check all the fuses above your left knee.

98 still has a distributor.

so put in a new cap and rotor and wire and plugs, "tune it up"

if no spark, then its:

Bad Distrubutor parts, major.

cmp sender, Ignitor and the coil is inside.

rebuilt distributors are sold by all major auto stores.

you should feel a vibration or shimmy in yoursteering wheel. also you can take you car to a les schwab and they could tell you

Its on the rear of the engine,twards the firewall area.pick up a Haynes Maunal and it wil show you exactly.

Beware the mounts are brittle,if you snap or crack the pipe expect to pay alot for both an EGR valve and the emmissions pipe

Separate the engine from the transmission. Removing flywheel or ring gear might be necessary for access. You can usually use a hammer and punch to tip the plug in it's hole and pull it out with pliers. When installing the new plugs, a small amount of permatex or shellac compound will insure against leaks.

yes!

It would usually cost around $900 because they need to remove the Trasmission. Most of the price is in the labor. The part is cheap.

If you get under your truck between the two front tires, and look up you should see it. It is cylindrical and is on the passenger side of your flywheel.

Bad radiator, gaskets, water pump, thermostat

If you are referring to the console housing inside the car, it is to allow you to change gear without having foot on brake, gently pull the small button and your shifter will release and move

It could be loose lug nuts, CV joints, U-joints, wheel bearing, bad tire or any number of problems not mentioned. But start with the above, in the order mentioned. If your car isn't front wheel drive, it doesn't have CV joints. If it IS front wheel drive it doesn't have U joints.

Follow the top rad hose to your intake manifold, where the rad hose is connected on the intake manifold is called your thermostat housing. Drain your coolant level some (preferably while the engine is cool to avoid burns) then disconnect the rad hose from the housing. Next undo the two bolts holding the housing to the manifold and gently remove the housing with the use of a small scraper. Once the housing is removed you'll find the thermostat. Simply lift the thermostat out of it's place, clean off and remaining gasket material from the base of the housing. Place the new thermostat in the manifold, then the new gasket in the proper position and finally the housing back on the manifold. Carefully tighten the bolts back in place (there is actually a torque spec for these two bolts) then reattach the rad hose and add new coolant to bring the fluid up to its required level.

The alternator may be going bad.

There is another fuse box (all minifuses) located under the dash on the drivers side, there is a 20 amp fuse that works both the radio and lighter there

yes it comes with hard top a toneau top and soft top.

The rear half(rear ashtray) of the console has to be removed first. Then take the 4 Phillips screw holding the shifter cover out. Lift the cover towards the shift knob, you don't have to takeit all the way off. The bulb is in the small tray next to the shifter shaft. daner@copper.net

Things were slightly different in my 2000 S70 which has a center armrest with cup holders. First pry loose the cover for the handbrake and then pull the cover off the handbrake handle. The entire center housing is held in place by two 8mm bolts. These bolts are hidden under a removable panel located inside the storage box under the center armrest. When you open the armrest box you will see a small tab at the bottom toward the front. The access panel can be removed by placing a screwdriver in the tab and prying gently. The two bolts are under this panel. Once the bolts are removed the entire center console can be lifted up. It is not necessary to completely remove it. The bulb is located on the driver's side of the shift lever in a white plastic housing. science@Joyner.ws

Could be several things.

If the blower works on A/C or vent it is good.

If the Heater core is not leaking (due to corrosion, which is a common problem) it is probably good.

Could just be the Temperature cable is off the the blower door not allowing air to pass over the heater core.

Just to name a few..........

use a 1.6-liter 4-cylinder engine

crank sencer

When I had the same problem it was the starter solenoid. It is built on the starter so you have to replace both. After the starter/solenoid was replaced I had no more problems.

P.S. If you take it to most major auto parts places they can check the starter but not the solenoid mine showed good but after I replaced it I never had that problem again.

inside of the door of the Monte Carlo there are two tan wires, a larger one, a smaller one, a blue wire, and a black, try to get some shrink rubber for wires or electrical tape either one, I prefer the rubber all you need to do is put it on one end before tieing the two wires each together and then take a lighter and heat the rubber and it will shrink around the exposed wires. When you put the door trim back on the locks will work I recently worked on a 1992 Monte Carlo with the exact problem.

you probably have a button or switch to turn overdrive on and off, it may be on the end of your shift lever, you probably want to keep the overdrive on, save you some gas, hope i helped