0
Chevy Venture
The Chevrolet Venture was a minivan manufactured by General Motors from August 1996 to June 2005. The car replaced the Chevrolet Lumina APV in 1997 and was sold as the Opel Sintra/Vauxhall in Europe.
2,194 Questions
How do you reset radio in a Chevy Venture?
My fuel gauge, odometer and radiator gauge isn't working and my radio says locked. How can I fix this?
We have a 95 Chevy lumina that did the same thing, we took the door off, and readjusted the door and had to rehang it, it has closed fine since then, but the motor I think has finally died, so I'm still without a way to open the door except manually, which is a pain when I'm loading and unloading things like girl scout stuff, groceries, people, etc..
Best of luck..
Where is the rear brake switch for a 1992 Chevy G20 Conversion Van?
hi there should be same as mine which is located behind the dash you can either access it from below the dash which is awkard or remove the instrument cluster panel and unbolt the heater controls and instrument cluster as the switch is located behind them hope this is of use to you nate
You can do it if you remove the heat shield it works.
You need to know what the timing marks are on a 1991 Pontiac sunbird?
go to autozone.com current vehicle choose car repair info vehicle repair guides it may be in there.
How do you drain 2002 Chev radiator?
There is a drain petcock located in the bottom tank of the radiator. Depending on which Chevy you have it may be located directly on the bottom with a protective sleeve around it or on the side of the tank facing the engine compartment.
How do you know the fan relay is bad in your 1998 Chevy lumina?
Put your finger on it then turn fan on/off, you should feel the relay latching "clicking"..
Why does the air conditioning smell in 2003 Chevy venture?
There are two small cabin air filters that are located behind the glove box and are accessed through the glove box. There is a small access door that can be removed and then you can pull out the filters. If these have not been changed, it could cause the air to smell from the air conditioner. These are expensive to replace (around $55.00 each). Try removing them and cleaning them as best you can before buying new ones. That might help reduce the smell when the air conditioner is on.
Where is the fuel gauge sensor located on a 2005 Chevy venture LS?
The fuel level sensor is located in the fuel tank and is mounted on the fuel "sender" assembly. This is the assembly that contains the fuel pump. The sensor comes as a unit with the attached float.
The sensor can be changed, separate from the fuel pump, but it may be a good idea to change the whole assembly while you are there IF you have had any problems with it. But you can save a little money by just changing the sensor.
You will have to drain and remove the fuel tank to get to the assembly.
What size tire does a 2003 Chevy venture van take?
Every vehicle has the correct tire size and the amount of air that should be maintained on the inside of the driver's door or else consult your owner's manual.
Where is the fuse for the horn located on the 1998 Chevy Venture van?
Hi,
Both the fuse AND relay for the horn are in the Underhood Fuse Block. I believe it is fuse 36. I have also included a link that shows a diagram and picture of this fuse block, along with a chart to identify the exact fuse. There should also be a diagram under the fuse block cover.
Good Luck
How do you repair abs light is on?
The front wheel hubs both sides contain the ABS sensors .Try the obvious first by unpluging both sensor wires at the hubs and spraying wd40 or something like into the connections and if that does not help go and get plugged into an ABS capable scan tool which should tell you which sensor is failing. IT could be of course the ABS module at worst but start with the cheap and easy fixes first. Best of Luck bud.
Where is the coil located a 1995 Chevy astro van?
`on the right side of engine in the center of engine
Looking for a motor for a 1999 Chevrolet venture?
no
I found an engine for my 97 from I think it was LQK it is a national salvage yard. They sell on eBay that was were I found there contact info.
I would try www.car-parts.com
You can find nearly anything for any vehicle anywhere in the country from salvage yards. They will send it to you if you can't find the part close by. I have purchased a transmission for 75 bucks that worked well utilizing this resource.
How do you change a headlight bulb on a 2009 Chevy Malibu?
Bad news for all that own this vehicle...the 2009 Malibu. It is not possible to change this the headlight bulb yourself!!? The designers of this car appealed to us with the euro look and good gas mileage. Unfortunately they did not notify us at the time of purchase that a simple task of changing your bulb will cost you upwards of $70.00. I had a bulb go 2 days ago and inquired with my dealer ship for the details on replacement as the owners manual suggests. I was amazed to find out that you need to remove portions of the front to gain access to replace a $10.00 bulb. It will be attached with a tool only the dealership has.
How do you replace the power steering on a 99 cougar V6?
pull the intake , and then pull the motormount and its under the motor mount
The mechanism that causes the arms to park is part of the rotating arm that make the wipers move. If the wipers function in all other ways except for parking, the problem is in the rotating arm. to be sure that this is the case, remove the cover that covers the wiper mechanism while the vehicle is off and the wipers are turned off. Turn the vehicle key on and turn the wipers on to the low setting. The arm should rotate clockwise. When you turn the wipers off, the wipers should stop near the bottom of the windshield then the motor should rotate counterclockwise a little more than half of a turn. This action will park the arms if all is working properly. If your arms go back up the windshield and stop near vertical then the problem is in the arm. To remove the arm, be sure that the power is off. Disconnect the positive terminal on the battery. Remove the arm by loosening the two 8mm bolts on the linkage that connect to the arm. Then remove the t30 bolt from the center of the arm. lift up on the arm and tap on the center bolt before it is fully unthreaded. This arm consists of many moving parts, all of which are necessary for the park function to work. The first thing to check is the small flip lever on the bottom of the rotating arm. It should move freely and be spring loaded to keep the lever pushed to the outside. If it is not free, use some penetrating oil and needle nose pliers to free it. The other thing that must be done is lube the remaining parts and work them by hand to free them of corrosion. The spring that wraps around the middle can be gently removed and all parts can be oiled and worked till they are free. To reinstall the arm, turn on the wiper motor without the arm attached in the delay function. When the delay function pauses the motor turn the key off and attach the arm with the flip lever on the bottom, just clockwise past the stop on the frame. Reattach the linkage and test the unit.
How do you check the fuel pump on my 1997 venture?
Drop the fuel tank. But if you just want to see if it's working, it should whurr when you start your car. If it isn't whurring.. then it needs to be replaced.
How do you know which oxygen sensor is not good from a Chevy Venture?
The code thrown will tell you which one is bad. Codes p0130 thru p0135 all refer to the upstream sensor under your coil packs. Codes p0136 thru p0141 all refer to the downstream sensor under the van.
How do you know when you need an alternator?
A new battery or one that tested good is in the vehicle and the car is still losing power. the alternator is what charges the battery while the vehicle is operating.
What if your Chevy van is making a humming noise in the rear?
The differintial is starting to wear...
Horn won't blow on 1984 Chevy?
No one can tell you how to fix something without knowing what is causing the problem.
Horn "failure" could be caused by one or more of several things.
In order to fix the problem, someone who knows what he/she is doing needs to troubleshoot the entire horn wiring system including:
- First the fuse for the horn circuit.
- All connectors, plugs, splices, etc. [for being disconnected, loose, or corroded]
- All wires in the horn circuit for cuts, breaks, orunintended grounding.
- The horn relay [if so equipped].
- The horn ground [for looseness and/or corrosion is key issue here]. Usually horns are grounded internally [no external ground wire] and thus are grounded by their mounting mounting bracket to the sheet metal of the vehicle. IF corrosion builds up between the mounting bracket and the sheet metal it's mounted on, then that acts like turning off a switch.
- Most horns operate using a vibrating internal set of points, and sometimes are adjustable. Over time, wear can cause the point "gap" to change and prevent the horn from working. The adjustment is a small "screw" on the back of the horn that doesn't have a "head," but only a small slot in the screw shaft. The screw has a nut which is used to "lock" the setscrew once it is properly adjusted. To adjust, insert a screwdriver in the slot and hold the screw while using a small open end wrench to loosen the lock-nut. Then have a "helper" hold the horn "button" down. While the horn button switch is being held down [switch closed], you gently turn the adjusting screw back and forth a little at a time until the horn starts to blow. Then continue to "tweak" the adjustment until the best horn "sound" is achieved. IF this process does not allow the horn to blow, then it's probable that the horn button/switch is defective.
- The last item to check is the horn switch button itself because it's inside the steering wheel cover and thus is the most difficult component to get to.
There are probably other things which don't come to my mind now. Good luck!
How do you remove the drivers side door panel on a 2001 Chevy Venture?
Hi,
The hard part is the bolts that are in there. Otherwise you just use a trim tool to CAREFULLY pop the edges out. I have included a link that has the description of the process and a few pictures.
Good Luck, Greg
