0
Dodge D100
The D100 was a light truck that belonged to Dodge’s D Series product line. Similar to other D Series models, the D100 was made for the Israeli army and civilian market.
565 Questions
Where is the crankshaft position sensor located on a 1999 Dodge Dakota Sport 3.9 V6 Magnum 4X4?
On a 1999 Dodge Dakota Sport 3.9 V6 Magnum 4X4, the crankshaft position sensor is typically located near the rear of the engine, mounted on the engine block or transmission bell housing. It is often positioned close to the flywheel or flexplate, allowing it to read the crankshaft's position. To access it, you may need to remove some components for better visibility and reach.
How do you remove the wiper arm on a 1993 grand am?
To remove the wiper arm on a 1993 Grand Am, first lift the wiper arm away from the windshield until it’s at a 90-degree angle. Locate the small retaining nut at the base of the wiper arm and use a socket wrench to remove it. Once the nut is removed, gently wiggle the wiper arm to loosen it from the splined shaft and pull it off. Be careful not to damage the windshield while doing this.
Where is the fuel pump relay on a 1989 Dodge d150?
On a 1989 Dodge D150, the fuel pump relay is typically located in the engine compartment fuse box. You can find the fuse box near the battery. The relay itself may be labeled, so check the diagram on the cover for specific identification. If you're having difficulty locating it, consulting the vehicle's service manual can provide more detailed information.
The weight of a Dodge D100 varies depending on the model year and configuration, but it typically ranges from approximately 3,500 to 4,500 pounds. Factors such as the engine type, cab style, and additional features can influence the exact weight. For a more precise figure, it's best to consult the specific vehicle's manual or manufacturer specifications.
What ia a ballast resistor made of?
A ballast resistor is typically made of ceramic or a special heat-resistant material. This material is chosen to withstand high temperatures generated by the electrical current passing through the resistor.
Where can you find a manual for a 1990 airstream land yacht for the electrical wiring diagram?
1984 was the very last year for Airstream service manuals. For a couple of years after Airstream produced only smaller owners manuals and by the end of the 80's there was nothing for several years.
vox231 on eBay has the 1984. Ask if it covers your needs.
Airstream is now offering reprints of service manuals for vintage Airstream and Argosy trailers.
I'd try a Hane's manual first. It would be the cheapest way to go. As a side note, if there are vacuum lines disconnected, it's possible that it was done to fool an emissions test to get it to pass. If you need to pass another emissions test, you might want to disconnect them again before the test (or spend the thousands of dollars replacing parts trying to get the truck to pass).
How do you adjust the shift linkage in a 1999 Dodge Durango?
Everyone should have a manual, and the library should have a professional shop manual available for copies in the reference section...read up and fix 'em like the pro's...! :) Dave
What is the ignition timing spec for a 1996 dodge ram 1500?
The distributor is not timed with a timing light. The distributor rotor is lined up with the mark in the pick up plate when the crank is at tdc#1. The computer then does all timing from there.
What should the degree of timing be for a 1994 Chevy truck with a 350 engine?
If this vehicle has the factory fan shroud it should say on it if you can still read the stickers on top of it.
Why wont your 1984 dodge startengine turns overhas fuel at carb does not have ignition spark?
== answer== Could be a bad ignition control module or coil,points if equiped,cap,or rotor,bad ignition switch.
Need to see a diagram of how the throwout bearing connects to the fork on 1975 D100 slant six Dodge?
Usually ball and socket
Where is the ballast resistor located on 1985 f250?
Should be on the drivers side inner fender and is porcelain. Hope this helps
Oil pressure switch location on 5.9L dodge ram 1500?
the switch is located on the back of the engine. right behind the intake manifold. right beside the egr pipe.
What are the head bolt torque specifications for a 1989 Ford Thunderbird 3.8L V6?
I have the shop manual in front of me with all specifications. I would be happy to assist you if I could understand what you mean...? "Head bolt" - - what head bolt - if you help me on this I will give you the torque spec! Cheers ...and if you do mean cylinder head to be bolted onto block - then it is as follows: Number the two rows of bolts as follows: top to bottom, left to right: 7,3,1,5 (top row) 8,4,2,6 (bottom row) For supercharged engine only (other engines have other specs!!!) Tighten the bolts in numerical order - * Tighten to 65-75 Nm (11-18 lb-ft for those that have not grown up...) * Rotate an additional 90 - 110 degrees (harder!) * Go to next bolt in sequence You do not need to retighten bolts later. This will do. Good luck.
What size motor did the 84 dodge D150 prospector have?
the Prospector had either a 318 cu id or a 360 cu id engine.
What gas stations in Chattanooga sell gasoline with no ethanol?
10% ethanol mandate went into effect about 2 years ago. they don't have to put a sticker on the pump unless it's more than 10%. Federal mandate!
Where is the diagnostic connector on a 1995 dodge truck?
The connector is along the wiring harness under the hood, on the firewall on the passenger side.
