0
Dodge Dakota
The Dodge Dakota is a mid-size pickup truck manufactured by Chrysler since 1987. The Dakota has been commonly used by many fire and police departments as bush truck, patrol car or off-road vehicle.
4,822 Questions
Where is the drain on a 2007 dodge dakota?
Engine oil drain, bottom of oil pan.
Ac drain, lower pass side of the fire wall.
trans, no drain.
Axle, no drain.
Engine oil drain, bottom of oil pan.
Ac drain, lower pass side of the fire wall.
trans, no drain.
Axle, no drain.
How do you replace the ball joints on 1997 E-350 Van?
From: http://en.allexperts.com/q/Ford-780/Ball-Joint-Replacement.htm Ball Joint Replacement [Ford Van] Remove the brake disc. Remove the wheel speed sensor. For additional information, refer to Section 206-09.
Remove and discard the cotter pin and nut.
Disconnect the tie-rod end.
Remove and discard the cotter pin and the nut.
Remove the pinch bolt adjuster.
CAUTION: To prevent damage to the ball joint seal and the ball joint socket, do not use a pickle fork-type remover to loosen the ball joints.
Remove the front wheel spindle.
Strike the lower end of the front axle to loosen the ball joint.
Remove the front wheel spindle.
To install, reverse the removal procedure.
Check and, if necessary, align the front end.
Remove the wheel spindle assembly. For additional information, refer to Wheel Spindle - E150-E450 in this section.
Position the front wheel spindle in a vise, and remove the snap ring from the lower ball joint.
CAUTION: To avoid damage to the components, do not use heat to aid ball joint removal.
Using the special tool and suitable receiver cup, remove the lower ball joint from the front wheel spindle.
Using the special tool and suitable receiver cup, remove the upper ball joint.
Installation
CAUTION: To avoid damage to components, do not use heat to aid installation.
NOTE: Clean the wheel knuckle ball joint bores.
NOTE: The lower ball joint must be installed first.
Using the special tool with suitable receiver cups, install the lower ball joint.
Using the special tool with suitable receiver cups, install the upper ball joint.
Install the snap ring in the groove at the bottom of the ball joint.
Install the front wheel spindle.
I've had 4 Craftsman mowers. All have been right hand (standard) thread.
What kind of motor oil should you use for a 1987 dodge raider?
From the Import Service Manual - 1987 Ram Raider:
2.6L 4cyl engine
Total oil capacity: 5 liters (5 1/2 quarts)
32 -120 °F SAE 20W- 20 40 50
-10 - 120 °F SAE 10W- 30 40 50
-20 - 60 °F SAE 5W- *20 30 40
*SAE 5W-20 Not recommended for sustained high speed vehicle operation.
Take you foot off the brakes. This may restore some traction so you can steer or apply the brakes more gently.
Yes it is most likely the clutch release bearing and i would say 400 to 600 is about normal for clutch replacement.
How do you wire up your truck to a 7 pin plug?
Check out this site, it may help you.
http://www.etrailer.com/faq-wiring.aspx
What are the tire sizes on a 1995 S10 4WD Ext Cab?
I have a 1996 S-10 4x4 Extended cab, but mine has the ZR2 Off Road package. It came with 31/10.50-15
Does lumina come with airbags?
Depends on the model year,which you failed to mention!The 1st generation 1990-1994 didn't offer at all.The 2nd generation 1995-2000 had standard dual front airbags on all models and for all the years.
How do you change a voltage regulator in a 1999 doge Dakota sport?
The engine computer (PCM) is the regulator, so you replace it.
The engine computer (PCM) is the regulator, so you replace it.
What is the firing order for a 2001 Dodge Dakota 3.9L V6?
The manual says it is 1-6-5-4-3-2. It turns clockwise. The 1 position is nearest the passenger side, just left of the mounting screw. It is hard to put a picture in words.
also look on the intake manifold it will say firing order.
The light is on because there is a problem with the ABS. It will go off after you have the system repaired. Now if you do not wish to repair the ABS then you will still have normal braking but possibly without ABS. You can either remove the ABS light bulb or place a piece of black tape over it. course....on all my hondas(3)...when the abs light would come on it had nothing to do with the brake system at all it was always some type of tail light, runner light or some type of lighting system within the car..... maybe this is it?
What causes ABS light to come on your 99 sunfire?
There are several causes for ABS light to come on the 99 Sunfire. This may be due to worn or leaking master cylinder, contamination of brake fluid, or leaking brake hose.
Why does your engine idle up and down while driving?
Could be your MAP sensor or Absolute Manifold Pressure sensor same thing usually mounted on or near the firewall and has at least two hoses"vacuum" going into it.
Location of the crankshaft sensor on a 1998 Buick Century?
the crankshaft position sensor is located right behind the harmonic balancer mounted on the timing cover
Where is the obd connection on 1998 eclipse?
just under the dash on the drivers side near the center console.
Where is your 2002 Dodge Dakota cabin filter located?
I don't think any 2002 Dakotas came equipped with cabin air filters. If any were, it would be located on the underside of the dash on the passenger side, near the transmission tunnel.
IF no fuel pressure and no spark first thing in the day when cold and the relays start clicking,
THEN replace the (PCM/ECM) Powertrain Computer Module AKA Engine Computer Module
THEN the crankshaft sensor if needed.
let me know how it turns out,
MySpace/TimFrentz
------------------------------
check the ignition switch and check the electronic fuel pump
-------------------------------------
WHAT DID YOU FIND OUT ABOUT THIS PROBLEM? I AM HAVING THE SAME ISSUE WITH A 94 DODGE RAM VAN. Please let me know. I get an error code 54 and 45 on the computer. 45 Is "open or short in transmission overdrive solenoid" which can be caused by the precursor engine error 54.
In most Dodges, especially my 94' Dodge Ram Van 3.9ltr, the code 54 is fuel sync related. Primarily related to a fuel, cam or crank sensor. My problem is still unresolved or confirmed by a solution so I can not provide a resolution but follow me on mySpace/TimFrentz or Facebook and I will share my final resolution with you when available.
My problem: When I turn my ignition on I have to wait several seconds for the fuel relay to click and then stop clicking. This signifies a shortage of power in the fuel pressure wiring systems. On a warm day this seams to only take seconds but on a day below 40 degrees it seems to take as long as 30 minutes and it doesn't seem to start clicking until I tap the relay or try to turn over the vehicle several times to build current or fuel pressure. What makes this issue even harder to diagnose is that the problem is also keeping the distributor from sparking. So far I have replaced the Crank Sensor, Distrbutor Cap/Rotar/Wires/Plugs, battery w/ 900crank amps, cleaned the negative contacts, checked fuses, fuel filter and pump, and changed oil/filter. I'm now researching the possibility of it being caused by an ignition system component.
*After each thing you try, disconnect the battery for 5 minutes so the computer reset's.
Let me know your progress: mySpace/TimFrentz
