0
Dodge Intrepid
In this category you can ask questions about Dodge Intrepids. These questions can include where to find parts, how to get help, or how to do it yourself.
1,915 Questions
What is part number pa66-gf33 for a 1999 Dodge Intrepid?
PA66-GF33 is NOT a part #. It is a formula of ABS Plastic used for Injection Molding. This code is found on parts like an Engine oil cap and other parts used in High temperature environments. PA66-GF33 is not an ABS code. It is for 33% glass filled nylon 66. Call out is per ISO 11469.
Where are bleed screws for heater pipes on 96 stratus?
Doesn't have any. The system should self bleed.
Where is the signal flasher located on a 2000 intrepid?
FRONT SEATING AREA, DRIVER SIDE, UNDER LEFT HAND SIDE OF INSTRUMENT PANEL BETWEEN JUNCTION BLOCK AND BRAKE PEDAL.
usually that sludge means coolant in the oil.might be a bad head gasket.
What is the torque value of the drain plug on the oil pan of a 1998 Dodge Intrepid 2.7L?
30 foot pounds.
How do you get the rotor off a 89-94 4wd pickup with locking hubs to change the brakes?
For a Toyota Pickup?? You do not have to remove the rotor to change the brakes, for that matter you do not have to remove the caliper either. To change the front brakes: 1) Remove cover on brake master cylinder. This will relieve pressure in the system for step 2. 2)Remove tire. Leafing the original brake pads in place C-clamp on brake pad and outside of caliper. Lossen the bleeder valve. Turn c-clamp to squeezed caliper pistons back. Fliud should squirt out of bleeder valve. Once the calipers are all the way back inot caliper, undo brake pad clip and pull pins back. 3) The old pads will slide out the back of caliper, insert new pads in and replace clip. 4) Don't forget to bleed the brakes. A chiltons manual will walk you through it step by step.
What kind of transmission oil you need for your Dodge Neon 2002?
If you are talking about an auto trans then you want to use ATF+4. There are two brands, Mopar (available from you dodge dealer and sometimes walmart) and Valvoline (available at most autoparts stores.
Why horn and cruise control quit working on 2001 Dodge Intrepid?
Probably a bad clockspring, be carefull that probably meens you're airbag is out of function too, Does the airbag light come on?
What kind of Transmission fluid does a 2003 Dodge Intrepid take?
Use only ATF+4 and do not use any Universal Fluid.
You need to have it checked for codes. You could have a cam sensor or crank sensor problem.
Where is the daytime running lights control module on a 1996 buick regal?
I believe it is up against the firewall, just above brake pedal on the left. It is approximently the size of a cigarette pack, black in colour. It has two (2) wiring harness connections. Good Luck!!
Replacing timing chain on a 96 intrepid?
Its a belt, not a chain. Water pump is belt driven, so replace that while your in there. Make sure that the crank and cams are on TDC before you put the belt on.
How do you remove the tail light assembly from a 2000 Grand Caravan if you can't get the plug off?
I just had mine replaced and I was having the same problem with getting the wiring to come out. I watched the man while he was replacing it for me. There is a orange insert thing at the bottom of the wiring plug. He pushed the top of the plug out(not all the way, as much as it could go) with a screw driver and then pressed on a release type button in the front and it came out.
Just replace mine on 2003 caravan, orange tab at bottom of plug slides out 1/4". then press tab at top in. Plug will slide right off.
How do you program 2005 Chevrolet trailblazer key fob?
1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.
4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.
10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.
11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).
Pull upwards on the belt. There should be only minimal play, and the power steering pump should not make a noise due to a belt that is too lose or too tight. This is really the easiest way to judge proper tension.
2000 intrepid cyl 6 is misfiring which cylinder is 6 27L?
passenger side front cylinder is number 1 and next is 3 and then 5 drivers side is 2 , 4, 6 last.
How do you set the timing mark on a 1999 Dodge Intrepid 2.7 liter?
The ignition timing is not adjustable. If this is the chain you're talking about, say it's stretched or that and the guides are worn (this is a very common issue on this car) then you'll need to replace the chains (there are 3) the guides (there are two) the tensioner and the water pump with a new unit. This is going to cost $500 to $750 for the part and it is a pain in the butt to do.
Why do Dodge Intrepid use so much gas?
If you use more than noirmal dodge intrepids ( get the amount it's supposed to use from a dealer) then have it serviced if it still seems to be dissapearing you may have a leak or maybe evaporating from either intake or fuel tank.
