0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
What is the timing for 95 dodge 5.9?
The distributor is set to 0 deg with a scan tool. It can not be done with a timing light.
Can you use atf in your rear end?
No you can not, It will burn the rear end up. You must use 80W90 gear oil only.
Refrigerant low pressure fill location for 2005 Dodge Ram 2500 diesel?
On top of the dryer (black can) near the firewall on the passenger side of the truck.
Location of position pedal sensor?
It is located on the side of the engine where the cruise/accelerator cable and A/T kickdown cable all join together.
a jack shaft is the small drive shaft from transfer case to front differential, brakes have nuthing to do with removal of a jack shaft maybe you mean removal of front axle
Does the tail lights in the middle suppose to come on when the head lights are on?
No. The one in the middle is a brake light, and should only come on when you put on the brakes.
When the disk brake pads wear down the "sensor" touches the rotor, causing a high-pitched sound to warn you that it's time to service the brakes.
If the sound changes when you apply the brakes, you should have the brakes checked. You may need to replace the pads.
What transmission does a1996 dodge 2500 v10 have in it?
The automatic is called a 46re. The manual is a nv4500.
What tool are needed to change a harmonic balancer on a 1999 dodge ram 2500?
A three jaw puller, a serpentine belt tool, and sockets/wrenches.
A three jaw puller, a serpentine belt tool, and sockets/wrenches.
Where is the knock sensor on a 2000 Tahoe 53L?
Under the intake manifild. There are 2. The rear one goes bad and sets the Check Engine Light.
How much transmission fluid to add after change in 1999 dodge ram 1500 5.2L 2-wheel drive?
The amount needed will depend on how long the pan was off. Start with three quarts, start engine, shift through drive and reverse. You the check the level idling in neutral. Add fluid slowly until at proper level.
Can you get the timing cover off by just loosening the oil pan on a 96 22 l?
REMOVAL & INSTALLATION 2.2L Engine NOTE: The following procedure requires the use of a special tool. 1. Remove the serpentine belt and tensioner. NOTE: Although not absolutely necessary, removal of the right front inner fender splash shield will facilitate access to the front cover. 2. Install a suitable engine support fixture. 3. Remove the engine mount assembly. 4. Remove the alternator rear brace, then remove the alternator. 5. Remove the power steering pump, then position it aside with the lines still attached. 6. Raise and safely support the vehicle. 7. Remove the front two oil pan bolts. 8. Remove the crankshaft pulley. 9. Unfasten the front cover-to-block bolts and then remove the front cover. If the front cover is difficult to remove, use a plastic mallet to carefully loosen the cover
What is the firing order for a 1986 318 dodge ram?
1-8-4-3-6-5-7-2 Distributor rotates clockwise.
1-8-4-3-6-5-7-2 Distributor rotates clockwise.
How wide is the 2012 RAM 2500?
The 2012 RAM 2500 is 6 ft. 6.9 in. (78.9 in.)12V front power outlet(s) wide.
Yes, ATF 4 can be used with ATF 3. THe only exception is do not use ATF 3 in a vehicle that requires ATF 4.
Will transfer case out of 2500 dodge work in 1500 dodge?
Without specific year and engine combinations the most likely answer is no.
It's a tough call, but the one we did a couple of months ago, had a bad computer. It would run good for a few minutes, and then start running rough, as if there was a load being placed on the engine. Then of course, it would cough and die. Have you checked the ignition module? It's the plate that the coils sit on, that has the wires connected to it. Most junk yards sell the complete coil pack (mount, ignition module and both coils) for 25-35.00 $.
