0
Ford E-150 Van
The E-150 belongs to Ford’s extensive product line of full-size passenger and cargo vans. Also known as the Traveler, the E-150 features excellent design and a roomy interior for passengers and baggage.
2,051 Questions
How do you replace the turn signal flasher on a 2007 ford E150?
You simply pull the old one out and push the new one in. Purchase a new one, and you will see what it looks like.
Where can i find 1993 Ford van vacuum schematics 5.0 engine?
You can find a 1993 Ford van vacuum schematics for a 5.0 engine in the car's owner's manual. You can also check with different auto stores.
How do you remove the light switch knob on a 97 Ford F-250 van?
Pull the knob out. There is a small slot in the side of the knob. Put a small flat blade screwdriver in the slot and pull the knob out. The screwdriver will release a clip and the knob will come off.
What oil type for 2002 E 150 ford?
According to the 2002 E-150 owners manual :
( 5W-20 )
With engine oil filter change ( 6 quarts / 5.7 liters of engine oil ) for all gasoline
engine sizes
?
How do I apply to havve my grandmas 78 new yorker overhauled by Chip and his crew?
I just had my timing belt changed for $350. This included replacing the water pump. Simce the water pump costs about $40 and requires the same labor as a timing belt change, it's wll worth haveing done at the same time. My Miata is a 2000 SE, the cost should be close as the work is the same for all the model years. There's probably a local Miata club not to far from where you live. Check out the http://www.miata.net site, club link. Connect with the club, they will know who does good work and what the going rate is in your area. Good luck, Jack
EVAPORATIVE EMISSIONS CONTROL SYSTEM: If you smell fuel vapors after stopping the engine, outside of the vehicle. Check your EECS system, which consists of 1. Purge control valve: check operation and hoses 2. Canister for fuel vapors: check for cracked case and cracked vacuum lines. 3. Fuel tank vapor vacuum line: from canister to tank. Blow into it, you should have very little flow through it after the tank is full of air. (DONT SUCK ON IT, LIKE POISION) 4. Fuel tank vent line: from tank to gas filler pipe. This is very hard to check, and is probably your biggest problem. If you smell fuel vapors after stopping the engine that are very strong after filling the tank, back by the fuel tank, this is probably your problem. Use a mirror and a flashlight to check the vent hose. Check where the tubing connects to the tank. Look very carefully and move the tubing when checking. Also feel around the tubing for cracks. This hose is 3/4" rubber tubing, you will probably have to use heater hose to replace it. There is a hose clamp, with a 5/16 hex head on them. Very hard to remove, use an old fashion spring clamp to replace it, much easier. I had the same problem, and it almost drove me nuts. Joedi
How do you replace 1999 E-150 spindle?
Where do you find one to replace .... LOL ...if you got one I'll buy it
How do you wire a 7 pin plug for trailer brakes into a 1994 Ford Econoline van?
Hello: I wondered if you could tell me how much your vehicle weighs in pounds since I am thinking of purchasing this exact year make and model ie. a 1994 Ford Econoline E250 Cargo Van 4.9L L6 FI and the question of the weight has become important? I can try to answer your question, as well but it will take me some time. Can you answer mine?
What is the engine timing for a 1990 ford econoline e-150 5.0?
10 degrees BTDC ( with EFI / electronic fuel injection )
unless engine compartment decal shows different
Diagram of a fuse box in a 1993 ford econoline van?
Is there a third fuse box for my 1993 ford econoline van for the rear heater
Where is voltage regulator located in 1975 ford econoline van?
If it's like my 1978 it's just in front of the battery bolted to the chassis at about the same height as the battery. You need to pull out the battery to get to it.
Where is the thermostat located on a 1987 Toyota Van Wagon LE 4 cylinder?
It's on the driver side of the engine. Open the "hood" and locate the lower radiator hose. Follow the hose to the engine and there is where the thermostat housing is.
AnswerI confirm that, removing the power steering pump will give you more room, though you can do it without moving anything. You are working on top of the alternator so disconnecting the battery is a good idea. Since the thermostat is mounted sideways on the engine, use form-a gasket on the new rubber O ring gasket to the metal neck piece (wait 20 minutes for it to set). Install the new thermostat and carefully install the neck piece with O ring gasket. It is easy to mis-align the O ring so take your time. The only way to check, that I know of, is to take a small mirror and flash light and check in the neck to see if the O ring is sitting right after you tighten down the two nuts.
How do you replace a driver side rear view mirror on a 2002 Saturn SL?
from what i have seen most of the saturns are made ideally the same.
The
I have knocked off a mirror on my 95 sc2 i owned a few years ago
Power or no power mirror you should use a flat head screw driver and gently pry off the cover in the front corner closest to the mirror. The mirror is bolted. Use a ratchet the right size and take it off. When your done put it back on . its easy as pie. I had power on mine. Its a 5 minute job or less. Good Luck.
my 86 had a switch about 10-15" above the floor behind the middle row of seats on the driver side, when the bed was down the switch was partially covered by the corner of the matress-hope this helps
Why did van goth cut his hear off?
because they were huge like hassaan mansoors ears in newsome highschool
How do you hook a trailer brake controller on a 1998 ford E-150 Conversion van?
I have a Prodigy Brake Controller I installed on my 1995 Econoline 150 cargo van about 3 months ago. Installation was tricky to say the least, but it wound up working really well.
I had to get the existing 4-pin trailer connector at the rear of the van's undercarriage to work with a Hopkins (aka "Hoppy") 7-pin connector on a travel trailer. What I did was first purchase the 7-pin Hoppy connector at an RV store, match the trailer connector contacts with enclosed wiring diagram to get the trailer lights working.
I then ran a single 12GA wire from the brake controller's brake control wire to the Hoppy connector (you have to follow the enclosed wiring diagram and manufacturers' instructions for the brake controller carefully.) I also used 10GA wire to the brake light switch to the "hot" contact at the top of the brake pedal (under the instrument panel.) Then connected the neutral return to the "cold" contact on the switch.
There was then the problem of how to power the brake controller. I used 10GA wire to a spare 12V cigarette lighter plug I happen to have and used the cigarette lighter to power the unit.
Most manufacturer's will recommend hardwiring the power to a intermediate relay between the controller and the hot side of the battery to maintain steady state power to the controller at all times.
I also connected a 12GA wire to the Hoppy for a trickle charge to the trailer battery (Aux 12V.) The diagrams enclosed with the Brake Controller and with the Hoppy will illustrate the connections far better than I can describe here.
E200
i have a 2001 ford e150 van that is missing not getting good fire dino check said #5 cielnder where are my plug s n wires at i cant see them
How do you replace exhaust manifold gasket ford 4.9 F 150 1996?
Exhaust Manifold Removal & Installation 4.6L, 5.4L and 6.8L Engines 1. Raise and safely support the vehicle. 2. Remove the front fender splash shield. 3. For the left-hand exhaust manifold, remove the EGR valve-to-exhaust manifold tube and disconnect the Differential Pressure Feedback Exhaust [DPFE] gas recirculation transducer hoses. 4. Remove the oil stick from the engine. 5. On the 4.6L and 5.4L engines, remove the catalytic converter-to-exhaust manifold bolts. On the 6.8L engine, remove the front exhaust pipe from the manifold. 6. Remove the exhaust manifold mounting nuts, then remove the exhaust manifold itself. 7. Remove and discard the old gasket. 8. Clean and inspect the exhaust manifold for damage. To install: 9. Position a new gasket and the exhaust manifold onto the engine block. 10. Install the mounting nuts and tighten, in the sequence shown, to 13-16 ft.lbs. [18-22 Nm] on the 4.6L and 5.4L engines. Tighten the nuts to 17-20 ft.lbs. [23-27 Nm] on the 6.8L engine. {Tighten the passenger side exhaust manifold bolts in the order shown-4.6L and 5.4L engines} Kriss x kross 11. On the 6.8L engine, tighten the exhaust manifold-to-front pipe fasteners to 27-34 ft.lbs. [34-46 Nm]. 12. On the 4.6L and 5.4L engines, attach the catalytic converter to the exhaust manifold, then install the catalytic converter-to-exhaust manifold bolts and tighten to 25-34 ft. lbs. [34-46 Nm]. 13. Install the oil stick. 14. For the left-hand exhaust manifold, install the PDFE transducer hoses if equipped, and EGR-to-exhaust manifold tube. Tighten the upper and lower fitting to 26-33 lbs. [35-45 Nm]. 15. Install the front fender splash shield. 16. Lower the vehicle to the ground.
Where is the blend door on a 1997 Ford van E-150?
I am not familiar with a "blend door". Can you elaborate more about this device? What does it do, what is its purpose, etc.?
I saw this question on another ANSWER website for a F150. The blend door is the mixing, distribution chamber on the heater. On the F150 it was on the cabin firewall just above the transmission hump. On the E150 (van) it should be under the dash. Follow the air distribution lines to their source. When I get a more descriptive answer, I'll include it.
Above your passenger's feet is some black plastic duct work. Behind this is the heater core and behind that is the blend door. It is driven by a stepping motor on the right side. If this isn't working pray that the problem is in the electronics that feed the stepping motor. Once you remove the motor it is almost impossible to get it back in. Getting to the door requires a lot of work taking out a lot of stuff from very awkward positions. If you pull the motor the door falls down which is the fresh air/AC position. To get heat the door must be rotated up.
Where the DPF Differitial Pressure Sensor on a 2000 Ford E-150 4.2 Engine Whats it look like?
It will be located along the intake manifold. It will look sort of rectangular. Metal usually. It will have two vacuum hoses connected to it along with a electrical connection. Just remove these and label the vacuum hoses remove the two screws and it comes off. (I thnk it is two or three screws) Sorry cant remenber exactly how many screws.
