0
Ford Ranger XL
The Ranger XL is a pick-up truck manufactured by the American automaker Ford Motor Company. Some of the notable features found in the 2010 model are Electronic Stability Control, and torso and head airbags in the front seat.
4,911 Questions
Did they make a positive traction rear differential for the 1985 Chevy pickup truck?
since 1973 Chevy pickups have used, as an option, a governor actuated locking differential manufactured by Eaton. this unit has clutches, like a limited-slip , but rather than using springs for a preload, it has a flyweight governor,which is linked to a cam faced side gear. the mechanism locks up the axle with a difference of wheel speed greater
than 100 rpm. This unit will not lock up at speeds greater than 20mph. Look for the code "g80" on your options list ,either in the glove compartment or under the hood on one of the wheel wells.
How much oil does a 2004 ford ranger 4.3 liter hold?
The 4.0 liter V6 engine holds ( 5 ) quarts with engine oil filter change
How do you replace a master cylinder on a 1993 Toyota Pickup?
remove brake lines, remove bolts on the bracket that holds the cylinder to the brake booster then its free.
Some cases you will have to pry open the brake shoes.
How do you remove the pick up box from the chassis of a Ford Ranger?
to rempve pickup bed, get under neath truck and cut off 6 bolts that hold bed to chassis. then disconnect any wires for lights, etc. then with a couple buddies,lift bed off truck
Does a 05 Ford Ranger have a timing chane?
In a 2005 Ford Ranger :
The 2.3 litre Dual Over Head Cam four cylinder engine has a timing CHAIN
The 3.0 litre V6 engine has a timing CHAIN
The 4.0 litre Single Over Head Cam , V6 engine has ( 3 ) timing CHAINS
answer
pump pedal 1 2 3 4 to the floor hold,other person open screw on slave cylinder tssssit close screw then release pedal very slowly motion up,make sure reservoir wil not come empty,repeat repeat repeat in exercise motion verry well,until no more tssssit tssssit and it will be solid fluid ,gain
It would also depend on how cold is cold, 35 degrees F below freezing or 35 degrees F above freezing.
The bolts are right hand thread (BUT) U DON"T want 2 remove the bolt in the center of he pully.U have 2 replace the tensioner & bracket assembly.There is many pounds of pressure on the tensioner spring
Where do you locate the diagnostic port entry on a 1987 Ford Ranger?
I believe that will be found under the hood, near the windshield, drivers side.
Where is the distributor located on a 2002 Ford Ranger?
On a 2002 Ford Ranger :
The engines ( 2.3 / 3.0 / 4.0 )
Have the Electronic Distributorless Ignition System ( EDIS )
So , there is no distributor
The engines use a coil pack with either 4 towers for the 4 cylinder , or 6
towers for the V6 engines
What size screws are required for the scope mounting blocks on the new T-Bolt Browning .22 rifle?
For that one, contact the Browning service department in Arnold, MO.
What is the fuse box layout for a 2003 ford ranger?
go to www.motorcraftservice.com from there you can get a pdf of the owner's guide, use left hand side of the page follow the links to the 03 ranger.(use the index at the end to find what page to look for fuse layout) this is FREE from ford, there is a lot of good info at the site as well (mode 6)
What fuse goes to the heater blower on a 1996 ford ranger?
In the power distribution box ( which is " live " ) located in your engine compartment near the brake fluid reservoir there is a
40 amp maxi-fuse for your blower motor in the row nearest the driver's side , and it
is the 3rd fuse from the firewall end of the PD Box , according to the owners
manual for the 1996 Ford Ranger
Where is the PVC valve on a 2001 Focus?
on the bottom half of the air box, theres a whole on the lower left that connects a pipe to the engine
How to replace rotors on a 97 tracker?
After you remove the wheel, there will be two large bolts holding the caliper in place, I believe 17mm. Loosen these two, lift & hang caliper, the roto will slide right off. Assemble with antiseize compound if you have any.
What does 'in hot water' mean?
It means that you're in trouble, or that you're going to be in trouble.
The image is of a person who has fallen into a hot pot of water and is going to get scalded.
I have read that the expression derives from times when hot water for bathing was in short supply and one using it out of turn would get in trouble.
However, the expression immediately suggests to me the cartoons and jokes I used to see in which missionaries or explorers were placed in a big soup pot by cannibals who captured them.
Cannibal Boy: I've brought a friend home for dinner. Cannibal Mom: Put him in the fridge and we'll have him tomorrow.
What happens if you upset a cannibal? You get into hot water.
you are in trouble so dont push it
Someone being "in hot water" means they are "in trouble".
I believe it means they are in trouble. Example: A student didn't do their homework and they might say ..."Geezz I forgot to do my homework. Boy am I in hot water now!
It means that through your own actions you have made a problem or difficulty for yourself. That you have got yourself into trouble.
What type of motor oil goes into a 2006 volkswagon jetta tdi?
It depends on the climate you live in. Consult the owners manual.
Its a system in which two bins are used one of green color and other of blue color.
biodegradable waste are dumped in green bin whereas non-biodegradable waste
are dumped in blue bin.it makes it easier for government authority to separate the two waste and to make them recycle.
I had the same problem with my 02 Ford Ranger the sensor is inside the door (genius idea ford). no amount of wd40 helped. luckily for me it was my passenger door. I just unplugged it and the dome light doesn't turn on for the passenger door but works find for the driver's door.
What can you do if the doors on your car won't unlock with the keys?
OK, I'm assuming you can lock/unlock the doors with the door pins. If so, you will need to pull one of the door lock cylinders (preferably the passenger door because it gets used less) and take it too a locksmith and have him make a key to fit it.
