Hand Tools

It is a 5/8

What wrench size is need for a 2007 Honda Civic oil plug?

It depends on which sensor you're working on (front or rear, and which engine size V6 or V8). It could be either the standard threaded type with the 7/8" hex, or the type with a flange that is held in place with bolts/nuts. If the sensor you're working on is the standard type without a flange, you can use an open-end 7/8" wrench if you have room. If not, there are special oxygen sensor sockets (with a slit at the side so the wires don't get pinched) you can use with an extension and ratchet. For the flange type sensors, all you would need is a socket (probably 12mm)or an open-end wrench if there's enough clearance.

A typical car's maintenance manual will quote at least 60 Torque settings. My Taurus manual has 74 torque settings. -The Ranger ( being 4WD ) will have at least 90 . - Do you seriously expect us to quote them all - -

15mm

You didn't say year, but most after '97 are 7mm Allen key.

the caliper bracket bolts use 18 mm wrench on a 03 1/2 ton 4x4

34mm for 2001 non-AWD

The calipers need a 7 mm hex wrench. The Caliper holder to remove the rotors takes an 18mm socket.

This is a 2003 Ford escape..apparently it's the same as a Mazda tribute.

It is a metric size. Crawl under the vehicle and try different sizes. Start with a 17 mm. Use a 15 mm i just changed my oil its a 13mm no doubt

3/8 inch Allen wrench.

Hand tools as suggested by the name are hand powered. Power tools all have a motor, usually electric.

This week, I have changed the brake pads on two vehicles that I have never worked on before. I jack them up and get in there with a full set of Allen keys and small wrenches within reach. I look and see if it needs an Allen key or wrench and approximately what size. Then I try tools that may fit till I find the correct one -usually within 2 tries. - This is not a complicated exercise. . . .

I thought my system had star bolts, not Allen bolts. You may need star wrenchs. I think mine were 10mm stars

I'm pretty sure that takes a 7mm Allen key.

They should be 7mm but sometimes replaced with 10mm so could be either hope this helps!

Ferrari used beta tools berfore this year.

The plural of wrench is wrenches.

You don't. Well, there are blue koopas waaay above the caves. Do you think what i think?

(thinks of dancing peanuts)

it is a 6mm allen wrench. A ball type allen works best to get to the plug.

A wrench is a wrench. A screwdriver is a screwdriver. Two different things, one cannot be in the other.

In most cases you just have to experiment. Try a wrench that looks about right. If it turns out to be too large, try a smaller one.

T50 or T55

to remove the front brakes you need a 7mm hex socket and a 10 mm hex socket

A wrench touching ONLY the negative battery post/terminal will not produce a spark. For the battery to short circuit and generate a spark, something must act as a bridge between the two pots/terminals.

If the wrench in question were to touch both terminals, or to touch the positive terminal and a ground (typically the chassis of the vehicle) you will see a spark because the metal body of the wrench would create a path for the electricity to travel.

Intentionally creating sparks in this manner is highly UNRECOMMENDED as it will quickly drain the battery and also generate large amounts of heat. I severely burned my hand last year by touching the negative battery terminal when my starter motor died. The inside of the motor had created a short circuit which caused the rubber covering to melt off of the involved wires in just a short time. Luckily I was able to remove the terminal and end the short. The burn I sustained was small in comparison to the amount of damage the battery and vehicle could have taken from it.