0
Mercury Sable
Manufactured by Ford Motor Company, the Mercury Sable was offered as a mid-size sedan in 1986-2005 and as a full-size sedan in 2008-2009. One significant feature of the vehicle was its front light bar – a lamp fitted between the vehicle’s front headlamps.
1,908 Questions
What size speakers are in a 1997-2000 Taurus - Sable?
See "Related Questions" below for more
What tools needed to change a starter?
Most starters have two or three bolts holding them in and one bolt holding the wire from the battery on. And you usually have to get under the car to get to it.
So...you need a floor jack, jackstands and wrenches in sizes to fit the bolts.
As for the procedure:
unhook the battery, jack up the car and put it on jackstands.
crawl under and find the starter
pull off the push-on wire that goes to the ignition switch. Unbolt the wire to the battery. Remove the two bolts holding the starter in place and remove the starter from the car without dropping it on your head.
Crawl out with it, take it to the auto parts store and trade it in on a rebuilt one.
Installation is the reverse of removal.
What tire pressure Mercury Sable?
Look in the glove compartment, there should be a sticker with that info. Or look in the owners manual if you have one.
Where is the flasher located on a 1996-1999 Taurus - Sable?
Look under your dash for a blue box screwed into the right side of the dash panel. This of course is done, with you laying on your back, and your feet in the back seat.
It's a blue box, about the size of half a twinkie (cream filled, golden sponge cake).
Remove the plug that holds it in, unscrew the screw that holds it to the frame, and go to Autozone or other parts store, to get a new relay.
You will have to reuse the metal piece that holds the relay to the dash panel, so be sure and save that before you throw the old part away.
Installation is the reverse.
First Squirt easing oil, No Kidding!Don't even try until you lubricate the "multifunction switch" behind the steering wheel, which usually causes this problem. Squirt easing oil into the hole where the Hazard switch sits. Be generous. Operate the switch repeatedly. Operate the turn-signal switch repeatedly. Add more easing oil if needed. If that doesn't work, get a replacement flasher from your local auto parts store for about $10 (or pay $40-50 at the Ford parts window). Look up under the dash to the left of the steering wheel for a blue plastic cube. Remove that and plug the replacement in. The easing oil trick worked for me!No kidding. It worked like a charm. I highly suggest trying it before you do anything else. easing oil also fixed my dome light switches. My Dome lights wouldn't turn off but after saturating the door latches on each door, the switches started working again. Fixing a Flasher on a 1996 Ford TaurusThe flasher (a single one for both turn signals and the hazard lights) is close under the dash left of the steering column. Original equipment is a blue plastic square that fits into a three-pole receptacle served by black, blue, and red-white wires.But don't rush to replace it yet. First, do what my friend learned to do from WikiAnswers -- squirt easing oil down around the Hazard switch button behind the steering wheel, where the "multi-function switch" is located. Be generous with the lubricant. Soak the switch good. Work the hazard switch on and off a dozen times. Then work the turn signal switch right and left a dozen times. If nothing improves, let it sit a few minutes, then try the flashers again. Add more easing oil.
If you have to give up on easing oil, check the fuses for the hazard and the turn signals lights (separate fuses). If they're good, remove the flasher and replace it ($10 at your friendly universal after-market parts store, ($40-50 at your local Ford dealer). Save the receipt so you can return the flasher for a refund, as my friend did after easing oil did the trick.
TestimonialHoly Cow! I just happened to be stuck with my wife's Grandfather's 96 Taurus today and the turn signals and flashers didn't work. I followed the overly simple procedure in the preceding two paragraphs and it worked like a charm. Suhweeet! AnswerThe manual I have says the flasher assembly is under the drivers side of the instrument panel and it is held in by one retaining screw. It shows a small square unit with three blades which plug into a connector on the end of wire. It appears to be screwed into an under dash brace member which supports the instrument panel. My flasher is failing intermittently. I haven't gotten around to replacing it yet, so I can't guarantee this description is accurate. I hope this information helps. AnswerIndicator flasher assy 13550. This is an electronic combination turn signal and emergency warning flasher. It is attached on the left hand side of the instrument panel reinforcement above the fuse panel. The main wiring harness is assy 14401. AnswerIt could be the flasher, another fuse, the turn signal switch or an electrical connector. You will need to get a schematic for the turn signal system then track back to where you get power. Follow the line to the point where you no longer get power they you will have found the source of the problem. AnswerThe Flasher Relay is located behind the left side of the instrument panel.There is no flasher on the 98 Sable, it has a LCM (Lighting Control Module) Dealer only item unless you wanna take a chance at the junk yard.
there is a light blue flasher relay under the steering wheel check and replace or check the fuse box in the same place
The flasher/turn signal is screwed into the metal support above the fuse panel, you must take the bottom of the dash off and remove the plastic cover. this is for a sable that has light out detection. Any questions, contact chrisvolkswagon@msn.com I know for Real. Look under your dash. Look for a Blue Box screwed into the right side of the dash panel. This of course is done, with you laying on your back, and your feet in the back seat. It sucks to get to, but it's the easiest to access once your under there. It's a blue box, about the size of half a twinkie. Remove the plug that holds it in, unscrew the screw that holds it to the frame, and go to Autozone to get a new relay. You will have to reuse the metal piece that holds the relay to the dash panel, so be sure and save that before you throw the old part away. Installation is the reverse. Be sure to read through the Related Question below on the Taurus - great tips & info that equally applies to the Sable. Flasher relay is located, behind left side of instrument panel. The Flasher sensor looks like a little aluminum can, and is located under the dash (provided they didn't include a dash cover) otherwise you'd have to unscrew it first from all it's mounting screws. The can is mounted on the steering column up a ways, (best way to see is to put your head up there, while your feet rest in the backseat, it's uncomfortable but it works. You'll see two cans, left/right, turn your key to the "on" position, and use the turn signals, and feel each can for a clicking feel/sound. Don't replace that one, unless you don't have turn signals either. Henceforth the other one is the Hazard/Flasher sensor. Pull out the wire clip (it's easier if you slide the can out of it's holding clip, pop in a new one, and get upright before you pass out. Check all of the fuses. If they are good change the flasher which is in the fuse box on some cars. The flasher on most cars is located around the fuse box under the dash, or attached to the underside of the dash. It is a small round cylindrical Can made of aluminum, or plastic.
AnswerIf your turn signal flashers stopped working, play with the emergency flasher button on top of the steering column. Our 97 Sable turn signals quit once and luckily I pushed the emergency flasher button in and out many times and the signals have worked ever since. But the emergency flashers don't work, but I can live with that.
The turn signal flasher relay is located behind the left hand side of the instrument panel at the left hand side of the steering column.
IT'S USUALLY ON THE FUSE BLOCK UNDER THE DASH ON THE DRIVER'S SIDE. IT OFTEN LOOKS LIKE AN ALUMINUM CYLINDER(SILVER) AN SIMPLY PLUGS IN.
it is truly under the driver-side of the dashboard, but near the outer edge. it is truly a blue cube(original) and held in place with one 7mm screw into a built-in clip. it is left of the code-checking jack and the screw head faces down. once the screw is removed, the cube and harness drop down. there is no retaining clip-thank God-just carefully pry the three-prong cube away from the harness. now, my replacement cube didnt have a place on it for the clip, but the clip can be glued onto the new cube. or, ty-wrap the works in place....But,,, I did find that another's response was correct!!! i didnt need to change my flasher-the hazard switch WAS truly gummed-up!! i used a few drops of alchohol-not wd40 (that scares the electrician in me)-exercised the hazard and turnsignals feverishly and they began working miraculously! and , i appreciated other info on changing those pesky front turn signal lamps! it IS an easy job of removing the three bolts of the headlamp,removing the headlamp to get to the harness of the turn signal and voila!!! I'll even add that my signal lense was full of water, but nothing that a couple of well-placed weep holes didnt fix!! happy motoring!!!
I can;t believe it but the oil works. It worked in 10 seconds. Thanks for the quick fix!!
The flasher relay is located behind left side of instrument panel. Purchase the Relay and you will know what you are looking for.
How do you remove rear seat on 96 mercury sable to change rear strut?
Not having done this on my 98 Sable (yet!), I took a look at the Autozone.com repair guide for replacing rear struts - see link in the below section titled "Related links".
NOTE: Autozone now requires free registration to access the repair guides. More than worth the extra effort for these photo/illustrated instructions.
It doesn't appear that the seat has to come out - just remove the plastic trim piece to get at the top strut mounting bolts.
If you do replace yours, it will be helpful to others if you add to this answer any tips and tricks you may discover from the experience.
How many iginition coils do a 2004 Mercury Sable have?
6
==========================================================
The above answer is correct if you have the 3.0 liter DOHC , DURATEC V6
engine in your 2004 Mercury Sable
---------------------------------------------------------------------------
If you have the 3.0 liter VULCAN V6 ( and the flex fuel version ) it has the
Electronic Distributorless Ignition System ( EDIS ) and has ( 1 coil pack
that has 6 towers for the spark plug wires )
Do you have to replace quick struts in a pair Or can you just replace one that has a broken spring?
You can replace the spring with proper tools. Be VERY CAREFUL a spring that is not caged can inflict serious injury.
What size wipers for a 1996-2002 Mercury Sable?
1996-2002 Mercury Sable Replacement Wiper Blades:
- Driver side: 24"
- Passenger side: 20"
- Rear: 18"
See sources and related links below for more information. Since there are currently over 22 different wiper arm attachments, do not buy wipers just by length only - be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment.
How do you change a light in the dashboard on a 2002 mercury sable?
Might be able to get at in from underneath but probably will have to remove the dash cover
Is there an access panel to the fuel pump on a 2001 Mercury Sable to avoid dropping gas tank?
No there isn't. You are stuck dropping the gas tank, period.
How do you repair code p0430 on a 1997 sable?
Trouble code P0430 means: Catalyst System Efficiency Bank 2 Below Threshold
First at all, replace 2 sensors before and after converter. If problem still exist, replace the converter with the new one.
Goodluck
Where is the fuse for the heater blower fan on a Taurus - Sable?
Blower Motor Fuses
Straight from the Owners Manuals
1986-1995 - Relay #A and B in the engine compartment distribution box (See "Related Questions" below)
1996-1999 - Fuse #13 (inside box) and relay #11 (engine compartment)
2000-2005 - Fuse / relay #3 and fuse #8
See "Related Questions" below for more information about fuses boxes in the Taurus / Sable.
Answer According to the Owners Manual, the blower motor relay/fuse is in the engine compartment fusebox, #11
See "Related Questions" below for more
What does ip mean on the dashboard Mercury Sable 1998?
If you mean the exclamation point and the " P " above the word " BRAKE "
in the lower right side of the gauge cluster in a 1998 Mercury Sable
that means either the parking brake / emergency brake is on , or the brake
fluid level in the brake master cylinder in your engine compartment is LOW
Where is the fuse box located on a 1990 Mercury Sable?
There are two. One is inside near the brake pedal. It is tucked up under the dash, but you can pull it down to access it. There is another bank of fuses inside the engine compartment. on the driver's side, up against the firewall, right on top.
steve phx az
What is the slot number in the fuse box for the power window fuse for 2000 Ford Taurus?
Click on the link below
Click on Owner Guides
The owners manual ( which includes the fuse diagrams ) can be viewed online
This Could Be Because The Belt Needs Tightening Up. Check The Tention Of The Belt. If It Doesn't Need Tightening Then Check The Powersteering Fluid. Regards Mark
How much coolant does a 2000 Mercury Sable need?
According to page #206 of the Owners Manual:
* 12 valve Vulcan engine (the smaller one) - 11.6 quarts
* 24 valve DOHC engine (no room left in the engine compartment - 10.6 quarts
See "Related Questions" below for lots more about Taurus - Sable coolant and radiators
Either the coolant level is low in the recovery tank or the sensor is defective or has a loose connection.
actually most of the time it's the floating magnet in the tank. the magnet goes up and down with the coolant level. If your coolant level is where it should be and it's not overheating then it's something to do with a sensor. but before you run out and buy a new one there a little trick you can do. loosen the tank (it's only one screw that holds it in) and give it a good shake for about 10 seconds. what happens is the floating magnet will get stuck making contact with the sensor and trick it into thinking the coolant is low. 90% of the time this is the problem!!
How do you fix a 1998 Mercury Sable if the AC stays on when heater is turned on?
cars that are equipped with ac are supposed to run when the heat selection is on : max a/c , a/c , mix or defrost. the ac pump dries the air that flows through it which helps to clear the windshield and also to help to feel cooler in the summer . i have pulled the plug on the compressor before to turn it off during the winter months but it is just fine to run
Also, heat settings keep the compressor running to prevent it from seizing. The number 1 cause of compressor failure was due to lack of use during the long winter months.
Where is the passenger fuse panel located on a 2002 Mercury Sable?
According to the 2002 Mercury Sable Owner Guide :
The fuse panel is below and to the left of the steering wheel , by the brake pedal ( it has a cover on it )
Also , the Power Distribution Box ( which is " live " ) is located in the front of the engine compartment near the battery
Why would the fuse blow every time the windshield wipers are turned on in a 2002 Sable wagon?
* in my experience i have found that the wiper motor cover is the problem, you may check your local mercury dealer there was a recall for this. you may also check the wiring I have seen wiring that has been eaten through by mice or other varments. * I took it to the Ford dealer for a dionostic test...$75!!! Turns out the windshield wiper motor had a short in it...Cost me $55 to replace it myself. But,on another note, we did find mice in the engine compartment earlier in the spring! So maybe they caused it!
How do you replace the water pump on a 1997 Mercury Sable?
first take of wire cover on top to give yourself more room then take off serpetean belt by taking a 15mm wrench to the tentioner and turn it clockwise to loosen belt then take off hose leading out the front of car the take off hte bracket thatthat holds a/c compressorbolts are 10mm them take off the nuts to water pump. before youcan get to hte lower hoses you must take off the front iner fenderwell. whatch out the heaterhose is a bear to get the clamp off. i took the big lower hose off first and then from top tyrned the water pump so i could get the clamp off for the heater hose needlessto say i change the clamp for a regular screw clamp once your there you can easily manuver the water pump out reverse to install.
The blinking means there is a condition that is causing damage to the converter. The cause would need to be troubleshooted.
