0
Oldsmobile Achieva
The Achieva was a front-wheel drive compact car produced by the defunct American carmaker Oldsmobile. This model was based on the GM N platform and offered as a 2-door coupe or 4-door sedan.
491 Questions
How can you identify where the low side service port on the AC system of a 1995 Oldsmobile Achieva?
I recharged the A/C on my 1995 Acheiva (3.1 liter V6) last month. The wrong service port is easy to find, just next to the hood latch on the "pinky sized" pipe with the sensor. I think the cap on that one is red, but pay attention to the diameter of the aluminum pipe. The correct diameter is fatter than this.
The correct service port is underneath the car, not too far from the oil drain. You will need to elevate the front of the car and chock your tires for this, unless you have a lift or a pit to work in. Since an A/C check requires the engine to be running to get an accurate reading, get a buddy (a.k.a. a witness) in case things go sour.
Now, crawl underneath your car and hunt for the service valve. Look for the aluminum pipe near the radiator. If memory serves, it is just behind the radiator, towards the center of the car, but slightly towards the passenger side. You are loking for a tee in the pipe. The valve points toward the ground, and it probably caked with engine crud. The valve cover unscrews, much like the one on the top side of the vehicle. Attach your meter, and follow the directions for testing. Recharge if necessary.
More safety: If possible, get out from under the car when testing or refilling. An extra couple feet of hose could save your life. Always think, "If my jackstands buckled, or the car rolled, where is the best place to be?" "Under the oil pan" is not the correct answer. There are more comfortable places to be trapped.
On a side note, mine turned out to have low refrigerant and a bad connection to the relay (passenger firewall relay bank, 2 green wires, 2 red wires), which added to the troubleshooting on mine. If your compressor isn't turning when your A/C is filled to the right pressure, then you may have an electrical issue. The schematics show at least four components which could electrically interrupt the compressor clutch.
In Most cases it is the aluminum hose with the smaller size diameter. Located on the iside fender well.
If your car has a 16V Quad 4 engine, then follow the two large freon hoses leading down to the A/C compressor. The Low Side Port is right beside the manifold block that bolts to the compressor.
This way, General Motors has made it as difficult as possible to get a service hose connected to it. You will burn your hands and melt down from the heat coming off the radiator.
I bought my last GM car back in 1982. It will be the last one I own as long as I live. I hate those poorly designed cars and the people who designed them. I feel no compassion for GMs financial troubles. I tried to tell them where they were going wrong 20 years ago but they would not listen.
I have been driving BMW automobiles ever since. Never have I been more completely satisfied with a car.
A/C is ALWAYS serviced on the LOW (suction/gas)side. The low side hose is ALWAYS the larger diameter hose. The high-side (liquid) hose will go INTO the firewall to the evaporator unit (possibly into a receiver-drier unit 1st). If the vehicle came OEM with 134 refrigerant, the snap-on connector on most charging kits will only connect to the low-side quick-couple fitting. Mark-Raleigh, NC
Why does the bright light idicator flash when the lights should be off on a 1996 Oldsmobile achieva?
It is due to your daytime running light not working properly or a burnt headlight, check your bulbs. I had the same problem and that was the problem.
Where is water in the drivers side floor coming from on 2001 Galant?
If it is just plain water, then you have either a leaking windshield or more than likely a stopped up A/C drain line. Look under the car passenger side and find the drain line and unclog it. If, on the other hand you have coolant leaking, then you have a leaking heater core, which must be replaced. Taste and smell the liquid. If it smells and taste sweet it is coolant and not just water.
How do you remove the console shift knob on an AT 1993 Olds Achieva?
To remove the console shift knob on the AT 1993 Olds Achieva, first pry the cover from the top of the shift knob. Then, access the single screw inside the cover of the shift knob and turn it counter-clockwise to release the knob.
How do you remove the automatic console shift knob on a 1992 Oldsmobile Achieva?
there should be a u shaped clip in the front of the knob, almost like a staple. pry that out with a screwdriver and the knob should pull off.
How does water get in the driver side floor in a 1978 Chevy Nova?
more than likely the windshield is leaking and the water is running behind the dash onto the floor.
What causes a bad odor when you first turn on the AC on a 1998 Oldsmobile Achieva?
Mold & Mildew buildup in the A/C condenser. Do a Google search for ways to kill it and remove the odor.
I also need an answer to this question, but my floorboard does not get wet. Is it clogged or is it a bad heater core? It is most likely a bad heater-core if it is antifreeze.
How do you change the ECM on a 1993 Olds Achieva?
It is in the right kick panel. You have to install a prom also/.
Sounds Like a problem with your sensors or elictrical components on your dash. Have you had issues with Water? We also have the 96 Achieva and I need to park it nose up to prevent water damage when it rains on floor..Ecspecially the drivers side
Still take to a qualified mechanic for a diagnostic. Ask for pricing in advance as some will do the service for free but most charge 50-80 or an hours labor :( Just to hook up to the machine.
Is there a sensor located in the catalystic converter on the 97 olds acheiva Se?
There should be one located between the converter and muffler if you have a V-6 model
How do you change the starter for a 1996 Oldsmobile achieva?
All except 2.3L and 2.4L (Quad -4) models
CAUTION: If it has the Delco LocII audio syatem, make sure you have the correct activation code before disconnecting the battery. 1) Disconnect the negative battery cable 2) Raise the vehicle and support on jackstands 3) Under the vehicle disconnect the solenoid wire and battery cable from the stater solenoid. 4) Remove the starter motor bolts 5) Remove the starter motor NOTE: the location of spacer shim(s) 6) Installation is the reverse of removal NOTE: Be sure to install the shim(s) in the same location
2.3L and 2.4L (Quad-4)
See CAUTION ABOVE
1) Disconnect the negative battery cable 2) Remove the intake air duct 3) Remove the cooling fan 4) Remove the oil filter 5) Remove the starter mounting bolts and pull the starter out enough to disconnect the battery cable and wiring harness from the solenoid 6) Lift the starter out between the intake manifold and radiator 7) Installation is in the reverse of removal
Edit: I just did this in my 97 4cyl and I just wanted to add to these instructions that you may have to unscrew the starter relay to get the cooling fan out. The starter relay is right next to the battery. Also, check the wires coming out of the starter relay. There is a purple wire that connects to a connector mounted above the oil filter. It's easy to accidentally unplug when you are installing the new starter, make sure you get it back in there or the car won't start.
1992 Oldsmobile Achieva how do you hood if release cable is broken?
Go underneath the front of car by the grill.Look up towards the hood latch.In the middle is a switch.Push it to the left and the hood should release.
Why does 1992 olds achieva just turns off while you are driving what could this be?
replace cam shaft sensor,location behind main pulley
A purge cylinder is a container used on the propane system. The cylinder aids in maintaining purity in gas lines.
What does a flashing high beam light on a 1995 Oldsmobile Achieva mean?
i have a 96 olds achieva and my high beam light was flashing, i checked the headlights and one of my low beam headlights was out. once replaced the flashing stopped.
What is the order of a timing chain for a '92 Oldsmobile Achieva S 2.3L?
You really neeed a manual to get it right. Get one at AUTOREPAIR2000.COM
change that calipers
replace your front rotors. checked your brake pads first though.
have you hit a curb? may also need front end alignment if so.
Most likely the rotors are so worn that the car vibrates when brakes are applied.
Put the "O" ring on the line and lubricate it with a little silicone.
How do you change the brakes on a 2000 Saturn SL?
I just finished a front and rear brake job on my 2000 SL2. I first went to Just Brakes and they told me what was wrong and wrote up a huge estimate. I couldn't afford that, so I went to the public library and checked out a Chilton repair guide. It has step by step instructions with pictures. Everything on the front discs are basically bolt on. The rear was a little trickier. I had to replace the wheel cylinders, so everything had to come off. Just take your time and only do one side at a time so you can look at the other. A good tip is to buy the rear spring kit and the tool to take the shoe clips off with. It took me about 3 hours to do everything and I saved over $300
Here is what I paid:
$20 front pads
$35 front calipers x 2
$16 rear shoes
$12 wheel cylinders x 2
$11 spring kit
$20 to have drums and rotors turned Good luck.
What is the torque on the intake of a 1993 Oldsmobile Achieva with a 3300 engine?
There are 10 bolts holding the intake manifold onto the engine block. Five on the back and five on the front. If you letter the bolts A through J from left to right, rear side then front, you get the tightening sequence below. Tighten bolts in the number sequence shown. A-7, B-3, C-1, D-5, E-9 F-8, G-4, H-2, I-6, J-10 Torque bolts to 88 in-lbs, making two passes in sequence.
What should be included in a tune up for a 1995 Olds Achieva S 3.1L V6 97k miles you just bought it?
change the oil, tranny flush, radiator flush, change fuel filter, serp belt and battery if needed
Where is the crank position sensor located on a 1996 Oldsmobile Achieva?
If you are referring to the SL 3.1 then they have two Crankshaft Position Sensor's, one is located in the front of the engine at the lower right corner just behind the Harmonic Balancer (which will have to be removed to get the sensor out) and the other one is located on the left side of the engine closer to the front of the engine about half way down just below the plugs. This one is hard to get to. (The front of engine is facing the passenger side of the car)
How do you fix the oil pressure in a 1994 Oldsmobile achieva?
Check the oil sending unit first, if this turns out not to be the problem then you might have a bad oil pump. If this is the case you should invest in a repair manual for vehicles that carry your make and model and year of car I bought mine for about 20.00$. good luck.
