The ECT power light came on while driving a 2000 Toyota RAV4 how do you turn it off?
Are you serious? There is a button in many Toyotas with automatic transmissions called "ECT Power." There is a corresponding light on the dashboard that comes on when the feature is activated with the button. The button causes the engine to rev to higher rpm's before the vehicle shifts to the next gear. It achieves higher accelleration than you can get without it, while sacraficing something in the way of gas mileage and engine wear. Just push the button again to turn it off. It's probably on the front of your center console, depending on your model.
Why would the transmission in a 1996 Lincoln continental not shift into overdrive?
I have a 1987 that is doing the same thing.
The computer systems chip is fried. The car runs fine and most everything works.
But, lately, the suspension won't charge while driving and will fault until the car is restarted.
The odometer also does not display mileage, just the word "error" where the reading would be.
My sub-questions to this issue is;
Does this systems chip control the transmission shifting to overdrive?
And the suspension system?
And is it the same performance chip that I see advertised for $69.00?
2003 four runner heater fan replacement?
I have a 86 and a 92. Check my posts for some hints I gave for these. In case you dont get any specific inputs.
How do you check the transmission filter on a Toyota Four Runner?
You have to remove the transmission pan. Although it is only a screen and not so much a filter it should not ever have to be replaced unless the transmission has failed completely.
What is it called when a runner tries to steal home and the batter tries to lay down a bunt?
In this situation, the term used is a "suicide squeeze". It sounds a little funny but the actual idea is this: Coach will give a sign to the batter to bunt. At the same time the runner at third base will run as soon as the bunt is layed down, sometimes if wanting to take the chance, as soon as the pitcher starts their delivery.
How do you tighten alternator belt so that it does not screech 2.5 Dodge Spirit?
Your pulley system that controls the motion of the belt and the tighness will either consist of 4 or five pulleys, with the Alt, being of course at the top. the very bottom pulley that likey can only be reached from under th car, should be your compressor pulley, the one in the middle, between the alt. and the compressor, should be your water pump with its pulley. Using the process of elimination, you can find out that there will be a pulley left, this is the belt tensioner pulley. It has a bolt in the center of it, it may be either 5/8 or 15 mm. This can be fitted with a wrench, or if you are lucky, a ratchet, and then turned as if you were loosening it, you will see the alt , pull up and it will be tightened this way, you may also want to apply some belt dressing. if this doesn't help , the belt may be squealing for another reason, such as the water pumb may be getting ready to go out or the compressor pulley may be getting loose.
Most likely. Same thing happend to my ZX7R, if I have the starter button pushed in and hit the relay with the back of a screw driver I can get the bike to start.
What is the advantage of Toyota 4 runner?
The advantage of Toyota 4 runner is that it is suitable for any terrain and has a backup camera.
Why is your 1993 4Runner hard to start in cold weather?
Check your battery first.. If it is fine, you might need to replace your cold start injector timing switch. Fairly expensive, but should work.
How do you remove glove box on 2004 Toyota 4-runner?
Simple: remove the small piston on the right side of the open glove box. Squeeze in the sides of the box to bypass the stops in the back of the box. It will fall forward. While you are at it open the long door behind the box and replace the "Cabin Air Filter' while you have it open.
How do you open the rear window if the button does not work?
You buy a new motor for the window or open it using the switch beside the driver door (if it is a relitively new car).
Coolant leak at thermostat housing on Toyota sr5?
The housing needs to be removed. Check for scratches on the housing or engine. Make sure that all of the old gasket is removed before using gasket sealer to help seal the new gasket.
How do you replace head gasket in 92 toyota 4 runner?
If you need to ask send it to the dealer or a #1 auto repair shop in your area.
Code for PO137 Bank 1 sensor 2 Where is this sensor located?
The sensor is left bank 1/1 is ft and 1/2 is the rear
NEW ANSWER: Bank 1 is the drivers side of the engine. Sensor 2 will be the second sensor in the exhaust pipe on that side of the engine. Start were the exhaust pipe bolts to the engine and work your way down the pipe until you see the second sensor and that will be the 1 you need.
What is the transmission fluid capacity on a 1994 Toyota 4 runner?
When doing a drain and fill on a Toyota 4 Runner, it takes about 4.5 quarts to refill. It is important to use the correct type of transmission oil.
Where is the headlight relay on a 1985 Corvette?
in the front (driver side) wheel well under a 6x6 cover mounted to the wheel well facing forward
there are 3 relays 2 are for the headlight motors left and right
How do you replace the left rear door glass on 2000 Ford Focus SE and how difficult is it?
The question you ask is too involved for a proper answer. You may want to go to a car parts store, or book store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
First of all, I had to remove the door panel by removing the door handle and by removing the torx screws that secured the panel. My Focus has manual windows, so I had to remove the window crank. This is held in place by a clip which is similar to GM vehicles. There is a white plastic pin (about 1/2" in diameter) that has to be removed from the window regulator. This single pin holds the window in place to the regulator. It takes some "playing with" to get the regulator in the proper postition to remove this pin. It removed easlily for me. In addition the outer molding on the outside of the door at the bottom of the window space had to be removed. This just pulls off. In addition the window rubber had to be partially removed from the rear side of the door (towards tail lights) and from the top of the door. Leave rubber hang leaving the rubber attached to the front side of the door. Obviously make sure all broken glass is removed from window track and rubber. We installed new glass by inserting it from the interior side of the door. It was installed at an angle without forcing. It was frustrating and it took some manipulation to acheive the proper angle. Once the proper angle was acheived the window easlily slid into place. At this time the pin was reinstalled through the regulator. I had to find the proper window heighth. My wife had to wiggle the window so the pin would slide properly through. After the pin was securely in place the door rubber was reinstalled with the window in the "down" postition. After this the door panel and molding was reinstalled. If there are any other concerns from you, you can contact Ford or consult with a repair manual or you may email us.
How do you install rear speakers for a 1994 Toyota 4Runner?
You have to take the whole back panel off. start from the tailgate there are parts to unscrew and then most of it comes off by pulling it off. there are plastic push pins in the plastic interior that needs to be removed and the speakers are under that
Try to use Toyota speaker adapter plugs so you don't need to cut wires and mess the electric system up. You can get them from Ebay or Amazon.Location of evaporator drain hose Chrysler 300 m 1999?
Preferrably on a lift, look at the angled body sheet metal that would equate to the engine side of the passenger side floorboard. In a space almost impossible to access (behind (aft of) the right side exhaust downcomer pipe) is a boot/curved hose molding. THAT is your evaporator drain hose. Mine dissappeared and has been allowing condensate to enter the car (which smells terrible.....mold!). I just purchased (today) the hose molding from my local dealer ($11.50 + tax). Now I just have to figure out how to get my big "meat hooks" up into that small space????? The service manager overheard my purchase from the parts dept. and did offer to install it for me if I could leave the car for a couple hours for the exhaust to cool off. I'm going to try myself, but may have to let Chrysler do it for me.
What is the curb weight of the 2005 Toyota 4Runner?
The curb weight of the 2005 Toyota 4Runner is 4045 lbs..
What ground clearance does the 2013 Toyota 4Runner have?
The ground clearance of the 2013 Toyota 4Runner is 0 ft. 9 in. (9 in.).