0
Toyota SR5
Manufactured by Toyota Motor Corporation, the SR5 (Sport Rally 5-Speed) belongs to the Hilux pickup truck product line. The Toyota SR5 was a popular option package in the North American market.
941 Questions
Where is the PCV valve on a 2002 Chevy S-10 Pickup?
some of the Chevy S10'S with the 2.2 motor did not come with a pcv valve depending where the motor was built due to emission control to see if your truck has one take off your air intake look in front of your throtle body on the passenger side of the valve cover on the side of the valve cover there will be a hose about six inches long coming from the valve cover to the intake
Where is the PCV valve on a 1990 Buick Century?
Under the alternator. You must remove the alternator to get to it.
Where is the PCV valve on 1990 Bonneville?
How does the fuses go in a 1992 Geo Metro?
They are located under the dash on the drivers side. You just plug them in the same way you pull them out.
Where is the PCV valve on a 2003 trailblazer?
There is no typical PCV valve in these trucks. There is a ventilation tube that is connected to the bottom of the Resonator box that sits on top of the motor. Says "Vortec 4200" on it. When you take the box off to clean the throttle body - yes clean it if you want to correct idle or stumbling when AC is on - you must ensure that it is reconnected along with the fuel Pressure switch vacuum tube.
Where is the PCV valve on a 2002 Pontiac Bonnevelle?
This answer is false there IS a PCV on a 2002 Bonneville. It is located on the Intake manifold on the left hand side. There is a sensor mounted on top of it. You need to disconnect the sensor first, then twist the sensor to the left and pull it off. It has an o ring underneath be sure to not loose this, and the PCV valve is now in plain view. Pull it out with a pair of needle nose pliers. It also has an o ring wrapped around it. This should come out with the valve to be reused. =) there is not one even though the books call for a fram 299 pcv valve so dont worry bout it
What is the tightening procedure on head bolts for a 1987 Toyota 22R truck?
O= valve springs += head bolts 8 6 1 3 9 + O + O + O + O + passenger side of motor + O + O + O + O + driver side of motor 10 4 2 5 7 this is the sequence from my haynes manual. i tried to emulate the diagram the best i could with the keyboard. the front of the motor is on the left. hope it helps and good luck.
On a 1992 Toyota SR5 V6 pickup does the water pump have a weep hole?
yes it does if your water pump is leaking its most likely from there and you will have to get a new water pump installed.
1996 Toyota 4 runner sr5 ac repair?
Anything is repairable but you need to let me know what is wrong with the a/c so that I can better help you !!!!!!!!!!!
Where is the PCV Valve on a 1989 Acura Legend?
It's on the front valve cover. The trick is you have to first remove the "breather chamber" by removing the 2 bolts on top. With the breather chamber cover off, you'll see the PCV valve screwed into the valve cover.
Where is the pcv valve on a 2001 Ford Ranger V6?
on an SOCH 4 cyl its mounted in the oil separator on the left side of the engine on an DOCH you have to remove the drivers side inner fender well to get to it
What are the torque specs for cam bearing bolts 1993 Toyota 3vze v6?
12 ft/lbs but its better to use 1/4" torque wrench set at 144 in/lb so you don't over tighten.
How do you fill and change the gearbox oil in 2001 Toyota hilux?
THIS IS FOR A MANUAL ONLY
HOW TO DRAIN THE OIL
There is a bung plug (24mm bolt) on the bottom which is used to drain the oil, replace bung after draining the oil.
HOW TO REPLACE OIL
There is an identical 24mm bung on the left hand side, about half way along and about half way up the side.
Remove the SIDE bung and pump oil in until it just starts to come back out the (SIDE) bung hole, then replace the side bung and your finished.
IMPORTANT: Make sure the oil pump hose is all the way in the bung hole, they tend to have a long threaded hole and if the oil hose is not in properly the oil will come back out and you might mistake it for being full.
Its also a good idea to know how much oil your gearbox is suppose to have, this can be found in owners manual. This will help make sure you have enough oil to do the job and make sure you replace enough oil.
You will need an oil pump, i brought one from "Auto Barn" for $19
What is the ignition timing for 1988 Toyota pickup?
Advancing the timing will not make the valves clatter, it will make the engine detonate if you're not running higher octane fuel! 5 degrees btdc is correct, and you can go as far as 3 degrees either way and still stay smog compliant (in California atleast) but advancing may cause detonation, which if left unchecked will cause severe damage to your engine!
look on underside of hood there is a sticker.
The timing on the 22re should be set at 5 DBTDC. It can be set ahead to 8 or 12 BDC if it doesnt cause the engines valves to "clatter" and "knock".
Where is fuel pump relay for 1990 Toyota pick-up?
fuel pump relay is in fuse box under hood
circuit opening relay is behind kick panel on passenger side
How do you reset the maintenance light on a 2004 Toyota RAV4?
For my 2006 Rav4, it has changed just a bit. The technique is the same, however, you apply it to the Trip A odometer instead of the actual mileage odometer.
I ran into the same problem with our '04 Toyota Rav4. I came across this website on reset the light. It mentions that "it may result in damage to your car's engine." How, I don't know. I'm thinking about trying to reset it as shown on this website, not sure yet. See for yourself. Cut and paste this link into your browser. Let me know what you think. Please reply.
http://24.228.55.27:3979/users/rilardi/toyota_reset.htm
This answer really is no help at all - go back to another poster's question "How do you reset the "Maintenance Required light on a 2004 Rav4" and you get the directions that work - they worked for me! Just continue to keep the odometer button pushed in until the light resets.
Turn ignition to the on position, depress the odometer selection button until it reads the total mileage. Then turn ignition off, whilst in off position depress odo button again, whilst maintaining button depressed turn ignition to the on position, the mileage will then change to read ------, then count down to -, then 000000, then back to the driven mileage. The light should then be extinguished. Refer to handbook pages 114-117.
Go to your Toyota dealership to avoid problems later on. You never know if you try to do it yourself and you end up making the situation worse. Let them look it over and reset it for you if necessary. That way, if they mess up they have to fix it.
Work for the Toyota Corolla 2005 as well. I reset the Maintenance Required light on my car by following the same instructions on this website for the RAV4. Turn ignition on to see odometer reading, set odometer to actual mileage, turn ignition off, depress odometer button and hold it while turning ignition on again. It will reset to 00000 and then to actual mileage. Maintenance required light will go off.
The maintenance light is really just an, as my dad calls them, "idiot light". It's meant to go off every 5,000 miles, and is a prompt to get your oil changed. If you have the oil changed somewhere besides the dealer, they probably won't remember to reset the light. (And the dealer doesn't always remember either, but if THEY don't, I bring it back and make them reset it just because they should know better, dag nab it!) If you record the mileage when you reset it, you'll see that it starts flashing a couple of hundred miles before the 5,000 mile marker, and then stays lit once you've hit 5,000 miles. My understanding is that it is NOT tied to any system, the way the check engine light is.
This method also works for 2009 Toyota Corolla (I have the S type). The way I did what by selecting the Trip A or 1, not the ODO (or total number of miles). But after this procedure the light is gone. My understanding is that this light is only to remind the driver that the oil change is due. I think most of the drivers do not need these type of annoying reminders.
there is a bypass hose that connects to the bottom drivers side of the pump. its right next to the thermostat housing. if that popped off, it would pour coolant out. i suspect that's your problem. a water pump would have to be REALLY bad for water to pour out of it. its not impossible though. to check remove the timing cover and fill the engine with coolant through the water outlet to the radiator. that way you'll be able to see if its coming from the pump. if not there are freeze plugs on either side of the block below the exhaust manifolds, check them to see if one came out
How do you access the expansion valve on a 1987 Toyota pickup?
SDI
Where is the ecu on a 1993 Toyota pickup?
The ECU is located right behind the passenger's side kick panel.
