Transmissions and Drivetrains

I wouldn't. Replace or repair the line instead.

There are 2 plugs on the bottom of the pan, You fill until it comes out the upper plug.

The engine has to be running and warm to get the right amount of fluid.

umm

unbolt both drive-shafts,then unbolt the auxiliary shift arm then unbolt the aux transfer case then unbolt main tran shift link unhook tran cooler lines (if automatic) put a jack under transmission unbolt transmission from motor slide trany back and down about 6in. transmission should come down(don't forget to remove the starter and dis-connect battery before you start)...

haha my step dad told me:) hes a mechanic

The turbines inside the converter.

Nothing good. Tighten the bolts and this becomes a mute issue.

It slips when you accelerate, the engine over revs going up steep hills, won't back up steep inclines, takes a long time to change up. -Any of those things mean you need to give it some attention now.

REMOVE the pin from the actuator rod to the wastegate

turn the rod adjusment nut little by little.... this WILL raise boost if you make it shorter AND WILL lower boost if you make it longer

Full-duplex

Both the vintage Borg-warner and the newer Richmond gear Super T 10 both have a capacity of 2.4 pints or you can just fill it till you can just touch the gear lube with your pinky through the fill hole.

the motor and trans must be lowered thru the bottom of the car. repair manual goes into detail . it took me 10 hours to complete with new motor install. remove all wireing harness assemblies and label.remove cover plate on bottom of bellhouseing ,this gives access to 4 bolts connecting the torque converter . turn crankshaft pully to rotate and access all 4 bolts.remove bellhouseing bolts and pull motor from trans. almost everything under the hood has to be taken apart and disambled.get the book! radiator,exhaust,motor mounts,altranator.powersterring ,wireing harness,cv half shafts. lower the motor with a cycle lift and jack the car up, block and pull the motor and trans out to disassemble. bag and label all bolts tag and label all parts and wire connections. most shops charge 600. bucks to do this and its well worth the money. this is a big job

You DO NOT HAVE TO REMOVE THE ENTIRE ENGINE. The transmission can be removed by itself .

low line pressure. take it to a transmission shop have the system flushed.(cooler, lines, transmission) new filter and fluid. tranny shop may also recommend a rebuild/replacement.

No

No

Assuming this is an auto box, check the fluid level first. After that check the fluid filter and pump. Then the brake bands. Then the torque converter. If a manual box it's either the layshaft bearings or synchro cones. A transmission shop will tell you for sure.

the sprag clutch ( overrun gear ) is gone and needs to be replaced

a new part can be bought but normally the complete starter is changed

in some cases squirting diesel oil on the sprag clutch can cure the problem

but it normally reoccurs again

if it moves without slipping or hezitation

If the D4 transmission gear light is flashing, it typically indicates a problem with the transmission system. First, check the transmission fluid level and condition, as low or dirty fluid can cause issues. If the fluid is fine, it’s advisable to consult the vehicle's manual for specific guidance and seek professional diagnostic help, as continued driving could lead to further damage. Avoid driving the vehicle until the issue is resolved to prevent potential transmission failure.

Low fluid, broken transmission.

If they worked on the transmission there should a warranty period.
Call them, then take it back and make them fix it. Good Luck and Remember.
Change Your Mind, Not Your Oil.
Use the First In Synthetic Motor Oil's.
See My Bio For more information. If the transmission is leaking and it won't shift, try checking the transmission pan and filter. They might not have replaced the gasket or filter.

I don't know! Ask a mechanic or something.

take bolts out the by a new one then put back on

Most Likely needs time to warm up. Oil is thicker when its cold so Lubrication between gears can be harder.

drain the box and change the oil is this dosent work try changing out the auto solenoids if they are available cheap otherwse there is not much you can do but bring it to a Honda agent and expect to pay big bucks for the fix.

Replace seals