0
Turn Signals and Hazard Lights
Turn signals and hazard lights refer to the lights on an automobile designed to alert other drivers or pedestrians. Turn signals indicate where the vehicle intends to go, while hazard lights warn others of an emergency.
4,468 Questions
How do you replace a front right turn signal assembly unit on a Jeep Liberty?
Before beginning, take note of whether you need a replacement bulb also. If you broke the turn signal assembly, there's a good chance you'll need a new bulb.
0.) Locate a suitable replacement assembly at a local dealer, salvage yard, or online parts retailer. Pay no more than $50. Don't forget to specify "driver or passenger" side, as this unit is not symmetrical.
1.) Disconnect the negative terminal from your battery using a 10mm socket/wrench.
1.5) Stop telling yourself that it's okay to skip step #1 and disconnect the battery already.
2.) Use T15 Torx head screwdriver to remove the only retaining screw from the unit. This screw is located on the front of the lens near the grille.
3.) Pull unit free from grill/fender. Grasp plastic assembly firmly in one hand. Grasp black bulb socket in the other hand. Rotate the bulb socket 30 degrees counterclockwise to separate the two pieces.
4.) Replace bulb if necessary.
5.) Clean any skin oils from the bulb with rubbing alcohol. Ignoring this warning will shorten the life of the bulb. Do this whether you replaced the bulb or not!
4.) Place bulb socket into replacement unit, rotating 30 degrees clockwise to secure
5.) Fit unit into grill and fender flare. Replace T15 Torx screw.
6.) Reconnect negative battery terminal.
7.) Turn your key one notch to "run" and turn on the turn signal to verify that it works.
Where is the signal flasher located on a 2003 Pontiac Grand Am?
Incorporated in the hazard warning module
part of the hazard switch
Where is the turn signal flasher located on a 2004 Honda Accord?
Relay is located under the dash above the fuse box (driver's side)(just above the hood release)(small black plastic can- 1" x 2'). I am going thru this problem as of now. Of course, finding a replacement is a challenge. Looks like I will have to go to a dealer (none in my area).
check the wiring harness for the opt. towing package under your left tail light
The turn signals and hazards lights do not work how do you fix this problem?
Could be the bulbs or the fuses or the flashers or the signal switch assembly
grounding. Almost always an inadequate ground for one or other the light assembly or most commonly the ground between trailer and tow vehicle (tongue ground is not enough) - inadequate ground can work with low current loads and behave as if dead circuit with the higher load of additional lamps.
Why should you use your turn signal well in advance or a turn?
Reason number one - it is a law.
Reason number 2 - it allows other drivers, pedestrians, and cyclists to know what your intentions are.
False. Pull over immediately. Turn on flashers. Do not drive until hood is back down and secured.
Any motorcycle in any state must be equipped with turn signals to be considered road worthy. Dirt bikes and other bikes without turn signals are considered illegal on main roads. Thank you for your answer to my question but I'm afraid you are mistaken. Currently only 20 states require turn signals. An additional 4 states require them based on the year of manufacture. (Data provided by Harley Owners Group) To rephrase the question; If I live in Indiana and my 1967 Harley is not required to have turn signals can I ride it to all of the lower 48 states without being illegal?
What is the Location of turn signal flasher for 2000 crown Victoria?
It's not a signal flasher.. It's Lighting Control Module. Located to the RIGHT of the steering column by the temp/ashtray assembly.. Under, what I assume would be the kick panel.. (mine's been taken off due to retired squad)
Where is the flasher for the turn signal of a 2000 Hyundai Sonata GLS located?
it is somewhere next to the fuses box...which is under the driver's dash by your pedals. It looks just like something you plug into your outlet, however I can't seem to find the right one for the flashers...I'm having the same problem as you it is somewhere next to the fuses box...which is under the driver's dash by your pedals. It looks just like something you plug into your outlet, however I can't seem to find the right one for the flashers...I'm having the same problem as you
Where is a 1998 Ford Ranger turn signal relay?
i have a 1998 Ford Ranger xlt 4wheel drive, my turn signals went out. where do i find the flash hazard relay?
How do you change a front signal bulb in a Buick Terraza?
To change the signal light on a Buick Terazza remove the headlight above the turn signal. Open the hood, there is one bolt/screw on the the top-outside edge of headlight and a 4--5 " L shaped fastner on the other side. Turn the L fastner and pull up and out. Now work the headlight out around the seals. The turn signal is directly below. Turn the light socket counter clockwise to remove bulb.
Where to locate signal flasher on a 1989 Chrysler new yorker?
There is a fuse box located right underneath the ashtray console. Within it there are 3 fuses. One should be labled as "Flasher".
My 1999 Ford Windstar left rear turn signal wont work.Bulb and flashers are good?
Check the fuses - specifically fuse #7 in this case.
See "Related Questions" below for more
How do you light a light bulb without electricity?
The only way a light bulb could be lit without electricity would be if it wasn't an electric bulb, or the "light" wasn't from an electric filament. I once had a miner's torch that was lit by igniting acetylene gas, but I wouldn't call it a "light bulb".
Electric light bulbs will only light with electricity. There is no other way short of breaking them open and igniting something inside of them, but then they aren't electric lights anymore.
<<>>
You don't. The design of an ordinary light bulb is to operate with a voltage supply.
Need more info on what you need ( bulb#, fuse#, hazard flasher, wiring color/gauge?) also need to know what year dakota? The owner's manual has bulb#/fuse amp/location.
Where is the Turn signal relay on a 88 Lincoln Lsc?
The flasher relay on your Lincoln Continental is located front seating area, driver side, under dash, driver side of steering column, above fuse panel, mounted on dash support bracket.
How do you replace front turn signal bulb on a 2003 Chevy 2500hd?
There are two l shaped rods under the hood above the head light assembly. Turn the rods out of their holders to release them and pull them up. The assembly will be able to be removed as one piece after the rods are removed, and you should be able to acess the turn signal bulb. Need more help contact me through my board and I will try to help.
Perhaps a short in steering column Remove all bulbs and check fixtures for corrosion Replace bulbs one at a time until fuse blows and further check or replace that fixture
Where is the turn signal flasher location on a 2002 Chevy silverado?
The Signal Flasher is on the back side of the Fuse Panel. To access it, remove the fuse panel cover in the driver side end of the instrument panel (you can see it when you open the door).
You will have to disengage the fuse panel from its mounting clips and work it to where you can turn it face down to access the flasher mounted to the backside. A pain in the butt!
I looked under there, and decided to try something different. I removed the two 7mm hex screws holding the lower dash fascia, and pulled the fascia off. The flasher was right there. Still a bit difficult to remove, but fairly straightforward.
What do the symbols on the fuse card represent?
The components/circuits that the fuse is protecting. best to look in the user manual for full list, sometimes there's not enough room on the card to show all of the protected circuits so the full breakdown will be in the manual.
Fuses:
1 Washer nozzle heaters 10 A
2 Turn signal lights 10 A
3 Fog light relay 5 A
4 License Plate Light 5 A
5 Comfort System, cruise control,
Climatronic, A/C, heated seat control modules 7.5 A
6 Central locking system 5 A
7 Back-up lights, speedometer vehicle speed sensor (VSS) 10 A
8 Open
9 Anti-lock brake system (ABS) 5 A
10 Engine control module (ECM): gasoline engine 10 A
11 Instrument cluster, shift lock solenoid 5 A
12 Data Link Connector (DLC) power supply 7.5 A
13 Brake and tail lights 10 A
14 Interior lights, central locking system 10 A
15 Instrument cluster, transmission control module (TCM) 5 A
16 A/C clutch, after-run coolant pump 10 A
17 Open
18 Headlight high beam, right 10 A
19 Headlight high beam, left 10 A
20 Headlight low beam, right 15 A
21 Headlight low beam, left 15 A
22 Parking lights right, side marker right 5 A
23 Parking lights left, side marker left 5 A
24 Windshield and rear window washer pump,windshield wiper motor 20 A
25 Fresh air blower, Climatronic, A/C 25 A
26 Rear window defogger 25 A
27 Motor for rear windshield wiper 15 A
28 Fuel pump (FP) 15 A
29 Engine control module (ECM): gasoline engine 15 A
29 Engine control module (ECM): diesel engine 10 A
30 Power sunroof control module 20 A
31 Transmission control module (TCM) 20 A
32 Injectors (gasoline engine) 10 A
32 Engine control module (ECM): diesel engine 15 A
33 Headlight washer system 20 A
34 Engine control elements 10 A
35 Open
36 Foglights 15A
37 Terminal (86S) on radio 10 A
38 Central locking system (with power windows), luggage compartment light, remote/fuel tank door, motor to unlock rear lid 15 A
39 Emergency flashers 15A
40 Dual tone horn 20 A
41 Cigarette lighter 10 A
42 Radio 25 A
43 Engine control elements 10 A
44 Heated seats 15 A
How do you replace the front turn signal bulb located on a 2000 BMW 323?
There is a hole on the edge of your hood that is directly behind the turn signal lamp. When you look directly inside, you'll see a piece of plastic. That's not where you need to go. Instead, go about 1 inch behind that and about 1 to 2 inches deeper. That's what you need to push down with a flathead screwdriver. Push down and forward to nudge the lamp out of its socket.
Hope this helps someone. It took me a LONG time to finally get mine out. I wasn't ready to pay another arm and leg to change something that was supposed to be simple. :) Good luck.
http://m3.madrussian.net/diy_front_turnsignal.shtml
AnswerExcellent help provided here - The only thing I would add is that you may want to use an extra long flathead screwdriver. The plastic tab that you need to press down on is pretty deep inside the hole.Answer
I agree this is excellent help. I just wanted to add that this also works for a 1999 BMW 323.
ANSWER
So easy!! Look in the little hole, the second in from the front. You'll see a little silver tab. It's plastic, don't break it. The tab you need is about 1.5 inches below. Poke around. It will just pop out, THAT EASY!! Don't remove any thing from the headlight assembly.
Where is the turn signal flasher located on a 1994 Olds Cutlass Ciera?
Behind the Ashtray I just fixed mine last night. It turns out that it was attached by a clip on the right side of the ashtray frame inside the dashboard. I took out the removable "cup" part of the ashtray, then removed the two upper and two lower ashtray frame screws. Next, I pulled the frame forward and disconnected the small ashtray light. The power wire for the cigarette lighter can stay attached. After that, it was easy to replace the flasher unit.
