Bumpers

"Beckett Guide to Baseball Memorabilia" states the pair are worth $125-150 in near mint condition, meaning full tip and no damage, tears or staining. ++ Please feel free to contact me with pictures and additional questions regarding these pennants or any vintage sports memorabilia. I've collected serious baseball memorabilia for 30+ years and am always interested in nice items and "finds."

Yes, any auto body shop should be able to repair

First remove the four 10 MM bolts holding the trans cooler and drop it down. Support it by attaching one bolt to the lower hole on the cooler frame. This will keep the weight off the lines. This takes two min. and allows easy removal of the elect. lines. Then remove the four bolts on each bumper. The bolts are 13MM and 17MM. You will need a ratchet, sockets, extension and a 13MM open end wrench. If you remove the rear bumpers, you should replace the rear pan with one of the aftermarket ones otherwise you will have big holes staring at the people behind you. Go to prowleronline.com and check the vendors for a couple of options. Maybe you are removeing them to paint and reinstall. Look at this link for some options .. Mine is the 7th post down. http://www.prowleronline.com/ubb/Forum1/HTML/014949.html Hope this helps. You can find me at prowleronline.com as BradleyG.. If you have more questions, join the POA and ask away. Great people and happy to help fellow Prowler owners.

A special tool called a BFH is needed. Any good mechanic will have one on hand.

According to the ( 1999 ) Ford Explorer Owner Guide , the 4 door is ( 191.2 inches long )

couple feet

first of all you need to take of screws on the coner of the bumper and the inside then under the bumper once you have done that there are 4 screws that hold the headlight on the bottom of the light on the passanger side it is easy to take off but on the driver side you need to go under the car between the radiator then you must unplug the headlight and it comes out i just did for my 95 it should be the same for 97.

It is a "splash shield". It is meant to keep water and off the engine and deflect air from sensitive components.

Almost certainly, it is illegal in most areas.

If you go to a loca junk yard you can get an almost new bumper for about $40. Then all you have to worry about is somebody painting it for you. At a Macco it should run about $100 or so.

How tall is Bumper Robinson?

I've never seen fog lights mounted OEM "in" the bumper on a 1996. However if your talking about on top of the bumper then that is easy. Just unbolt them than take them apart and replace the bulbs. Or do what I did and install newer aftermarket ones, they work much better. With the aftermarket lights you may have to modify the OEM brackets a bit. I used rubber spacers to help hold the new lights in place and cut down the vibration. If your lights are mounted in the bumper, you will have to remove the bumper.

2001-2002 I know the screws are behind the trunk panel. Two on each side I think and the ones in the back.

I have a 1969 Oldsmobile Cutlass supreme. My car has a 1968 front bumper, hood, and grill. Its mirror of your question but If a 68 can go on a 69 I wouldn't see why a 69 couldn't go on a 68.

Tell them to see you in court; you don't owe them a THIN RED DIME.

lb and rb if you look at your controller

Under the cover there should be two screws. On my '02 Firebird they were a star screw. Taking those two screws off let the panel come out.

you take it off and then you put the new one on!

I would say yes. It doesnt matter how much damage was done to the cars. It is still considered an accident. Im sure it would get thrown out by a judge.

undo two or three screws just inside both front wheel arches then where the bonnet meets bumper there are little black plastic gromets , take them out, then pull bumper away from front wings they should pop out of plastic slides then go to front of car and pull complete bumper fowards and off.

Whirly ball

You don't. Instead, you replace the entire assembly.

I've done it but it was years ago and I'm working from a poor memory. The grill has to come out to give you access to the fasteners holding the plastic bumper cover on. They are held by an ingenious little plastic clip that you access from the front of the vehicle. These "Clips" have to be rotated 90 degrees to unlock them and there are 8 or so total to undo. Look around the edges of the grill and you will spot them. once you get access to the bumper cover there are screws on the top and bottom of the cover that must be removed to get access to the bumper structure. The "bumper itself is pretty easy to replace as it is just bolted to the frame; getting access to it is the trick I think I also remove the headlights to allow access to the bumper cover as well. Good luck.

http://www.bfranker.badz28.com/fbody/repaint.htm this has everything you need to know to remove bumper cover just ignore the stuff about repainting unless that's what u plan to do

The fog lights are turned on by pressing the fog light button on the headlight switch. On my truck, you have to pull the switch out that turns the regular lights on.